[ Upstream commit 25faa5364638b86ec0d0edb4486daa9d40a0be8f ]

This commit addresses two issues causing i2c detect to fail.

The identified issues are:

1. Incorrect error handling for BED (Bus Error No ACK/NAK):
   Before this commit, Both ALD (Arbitration Loss Detected) and
   BED returned -EAGAIN.
2. Missing interrupt status clear after initialization in xfer():
   On the K1 SoC, simply fixing the first issue changed the error
   from -EAGAIN to -ETIMEOUT. Through tracing, it was determined that
   this is likely due to MSD (Master Stop Detected) latency issues.

   That means the MSD bit in the ISR may still be set on the next transfer.
   As a result, the controller won't work — we can see from the scope that
   it doesn't issue any signal.
   (This only occurs during rapid consecutive I2C transfers.
   That explains why the issue only shows up with i2cdetect.)

With these two fixes, i2c device detection now functions correctly on the K1 SoC.

Fixes: 5ea558473fa31 ("i2c: spacemit: add support for SpacemiT K1 SoC")
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Michael Opdenacker <michael.opdenacker@rootcommit.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20251113-fix-k1-detect-failure-v2-1-b02a9a74f65a@linux.spacemit.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert commit 690de2902dca ("i2c: muxes: pca954x: Use reset controller
only") and its dependent commit 94c296776403 ("i2c: muxes: pca954x:
Reset if (de)select fails") because the first breaks all users of the
driver, by requiring a completely optional reset-gpio driver.  These
commits cause that mux driver simply stops working when optional
reset-gpio is not included, but that reset-gpio is not pulled anyhow.

Driver cannot remove legacy reset-gpios handling.

Fixes: 690de2902dca ("i2c: muxes: pca954x: Use reset controller only")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

Add "INTC10D2" ACPI device-id for MTL-CVF devices, like the Dell Latitude
7450.

Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2368506
Signed-off-by: Hans de Goede <hansg@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Israel Cepeda <israel.a.cepeda.lopez@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

This reverts commit 1a2b423be6a89dd07d5fc27ea042be68697a6a49 because we
got a regression report and need time to find out the details.

Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Closes: https://lore.kernel.org/r/29ec0082-4dd4-4120-acd2-44b35b4b9487@oss.qualcomm.com
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

Pull more i2c updates from Wolfram Sang:

 - Second part of rtl9300 updates since dependencies are in now:
    - general cleanups
    - implement block read/write support
    - add RTL9310 support

 - DT schema conversion of hix5hd2 binding

 - namespace cleanup for i2c-algo-pca

 - minor simplification for mt65xx

* tag 'i2c-for-6.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  dt-bindings: i2c: hisilicon,hix5hd2: convert to DT schema
  i2c: mt65xx: convert set_speed function to void
  i2c: rename wait_for_completion callback to wait_for_completion_cb
  i2c: rtl9300: add support for RTL9310 I2C controller
  dt-bindings: i2c: realtek,rtl9301-i2c: extend for RTL9310 support
  i2c: rtl9300: use scoped guard instead of explicit lock/unlock
  i2c: rtl9300: separate xfer configuration and execution
  i2c: rtl9300: do not set read mode on every transfer
  i2c: rtl9300: move setting SCL frequency to config_io
  i2c: rtl9300: rename internal sda_pin to sda_num
  dt-bindings: i2c: realtek,rtl9301-i2c: fix wording and typos
  i2c: rtl9300: use regmap fields and API for registers
  i2c: rtl9300: Implement I2C block read and write

Pull USB / Thunderbolt updates from Greg KH:
 "Here is the big set of USB and thunderbolt drivers for 6.18-rc1. It
  was another normal development cycle, with lots of the usual drivers
  getting updates:

   - Thunderbolt driver cleanups and additions

   - dwc3 driver updates

   - dwc2 driver updates

   - typec driver updates

   - xhci driver updates and additions

   - offload USB engine updates for better power management

   - unused tracepoint removals

   - usb gadget fixes and updates as more users start to rely on these
     drivers instead of the "old" function gadget drivers

   - new USB device ids

   - other minor driver USB driver updates

   - new USB I/O driver framework and driver additions"

  The last item, the usb i/o driver, has an i2c and gpio driver added
  through this tree. Those drivers were acked by the respective
  subsystem maintainers.

  All of these have been in linux-next for a while"

* tag 'usb-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (132 commits)
  usb: vhci-hcd: Prevent suspending virtually attached devices
  USB: serial: option: add SIMCom 8230C compositions
  thunderbolt: Fix use-after-free in tb_dp_dprx_work
  usb: xhci: align PORTSC trace with one-based port numbering
  usb: xhci: correct indentation for PORTSC tracing function
  usb: xhci: improve TR Dequeue Pointer mask
  usb: xhci-pci: add support for hosts with zero USB3 ports
  usb: xhci: Update a comment about Stop Endpoint retries
  Revert "usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running"
  usb: gadget: f_rndis: Refactor bind path to use __free()
  usb: gadget: f_ecm: Refactor bind path to use __free()
  usb: gadget: f_acm: Refactor bind path to use __free()
  usb: gadget: f_ncm: Refactor bind path to use __free()
  usb: gadget: Introduce free_usb_request helper
  usb: gadget: Store endpoint pointer in usb_request
  usb: host: xhci-rcar: Add Renesas RZ/G3E USB3 Host driver support
  usb: host: xhci-plat: Add .post_resume_quirk for struct xhci_plat_priv
  usb: host: xhci-rcar: Move R-Car reg definitions
  dt-bindings: usb: Document Renesas RZ/G3E USB3HOST
  usb: gadget: f_fs: Fix epfile null pointer access after ep enable.
  ...

cppcheck rightfully reports:
drivers/i2c/busses/i2c-mt65xx.c:1464:6: warning: Condition 'ret' is always false [knownConditionTrueFalse]

Make the function void and simplify the code.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Functionally no change. Remove the ambiguity of 'wait_for_completion'.
It helps development of the DEPT dependency tracker, but seems favorable
in any case.

Signed-off-by: Byungchul Park <byungchul@sk.com>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

i2c-host for v6.18, part 2

rtl9300 updates:
 - general cleanups
 - implemented block read/write support
 - added RTL9310 support