linux-stable.git/drivers/i2c, branch v5.4.55 Linux kernel stable tree i2c: i2c-qcom-geni: Fix DMA transfer race 2020-07-29T08:18:35+00:00 Douglas Anderson dianders@chromium.org 2020-07-22T22:00:21+00:00 93bb40b79e84176b4d0da031b7cc467a8543ac04 [ Upstream commit 02b9aec59243c6240fc42884acc958602146ddf6 ] When I have KASAN enabled on my kernel and I start stressing the touchscreen my system tends to hang. The touchscreen is one of the only things that does a lot of big i2c transfers and ends up hitting the DMA paths in the geni i2c driver. It appears that KASAN adds enough delay in my system to tickle a race condition in the DMA setup code. When the system hangs, I found that it was running the geni_i2c_irq() over and over again. It had these: m_stat = 0x04000080 rx_st = 0x30000011 dm_tx_st = 0x00000000 dm_rx_st = 0x00000000 dma = 0x00000001 Notably we're in DMA mode but are getting M_RX_IRQ_EN and M_RX_FIFO_WATERMARK_EN over and over again. Putting some traces in geni_i2c_rx_one_msg() showed that when we failed we were getting to the start of geni_i2c_rx_one_msg() but were never executing geni_se_rx_dma_prep(). I believe that the problem here is that we are starting the geni command before we run geni_se_rx_dma_prep(). If a transfer makes it far enough before we do that then we get into the state I have observed. Let's change the order, which seems to work fine. Although problems were seen on the RX path, code inspection suggests that the TX should be changed too. Change it as well. Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller") Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 02b9aec59243c6240fc42884acc958602146ddf6 ]

When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang.  The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver.  It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.

When the system hangs, I found that it was running the geni_i2c_irq()
over and over again.  It had these:

m_stat   = 0x04000080
rx_st    = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma      = 0x00000001

Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.

Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().

I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep().  If a transfer makes it
far enough before we do that then we get into the state I have
observed.  Let's change the order, which seems to work fine.

Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too.  Change it as well.

Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: rcar: always clear ICSAR to avoid side effects 2020-07-29T08:18:35+00:00 Wolfram Sang wsa+renesas@sang-engineering.com 2020-07-04T13:38:29+00:00 58637b3027db74dbfbf7849f03a4bb681fb6e27f [ Upstream commit eb01597158ffb1853a7a7fc2c57d4c844640f75e ] On R-Car Gen2, we get a timeout when reading from the address set in ICSAR, even though the slave interface is disabled. Clearing it fixes this situation. Note that Gen3 is not affected. To reproduce: bind and undbind an I2C slave on some bus, run 'i2cdetect' on that bus. Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit eb01597158ffb1853a7a7fc2c57d4c844640f75e ]

On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.

To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.

Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: eg20t: Load module automatically if ID matches 2020-07-22T07:32:53+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2020-07-02T10:15:27+00:00 77a181fba1e58139f5b7939ff5a429ed56eee24d [ Upstream commit 5f90786b31fb7d1e199a8999d46c4e3aea672e11 ] The driver can't be loaded automatically because it misses module alias to be provided. Add corresponding MODULE_DEVICE_TABLE() call to the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 5f90786b31fb7d1e199a8999d46c4e3aea672e11 ]

The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: mlxcpld: check correct size of maximum RECV_LEN packet 2020-07-09T07:37:54+00:00 Wolfram Sang wsa+renesas@sang-engineering.com 2020-06-28T11:52:44+00:00 9d60af5c3bb3f7fca9fbffaf5eaa0f0514058594 [ Upstream commit 597911287fcd13c3a4b4aa3e0a52b33d431e0a8e ] I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno to what is suggested for this error. Fixes: c9bfdc7c16cb ("i2c: mlxcpld: Add support for smbus block read transaction") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Michael Shych <michaelsh@mellanox.com> Tested-by: Michael Shych <michaelsh@mellanox.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 597911287fcd13c3a4b4aa3e0a52b33d431e0a8e ]

I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno
to what is suggested for this error.

Fixes: c9bfdc7c16cb ("i2c: mlxcpld: Add support for smbus block read transaction")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Michael Shych <michaelsh@mellanox.com>
Tested-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665 2020-07-09T07:37:54+00:00 Chris Packham chris.packham@alliedtelesis.co.nz 2020-07-01T22:39:11+00:00 b460fc9d0525a1dbab068acf498a73db89695468 [ Upstream commit cd217f2300793a106b49c7dfcbfb26e348bc7593 ] The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck low, this differs to the PCA9564 which uses 90h for this indication. Treat either 0x78 or 0x90 as an indication that the SCL line is stuck. Based on looking through the PCA9564 and PCA9665 datasheets this should be safe for both chips. The PCA9564 should not return 0x78 for any valid state and the PCA9665 should not return 0x90. Fixes: eff9ec95efaa ("i2c-algo-pca: Add PCA9665 support") Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit cd217f2300793a106b49c7dfcbfb26e348bc7593 ]

The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indication.
Treat either 0x78 or 0x90 as an indication that the SCL line is stuck.

Based on looking through the PCA9564 and PCA9665 datasheets this should
be safe for both chips. The PCA9564 should not return 0x78 for any valid
state and the PCA9665 should not return 0x90.

Fixes: eff9ec95efaa ("i2c-algo-pca: Add PCA9665 support")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: core: check returned size of emulated smbus block read 2020-06-30T19:37:02+00:00 Mans Rullgard mans@mansr.com 2020-06-13T10:41:09+00:00 5cee9e67596f7d694e94d7def7cd9d65a7599f66 [ Upstream commit 40e05200593af06633f64ab0effff052eee6f076 ] If the i2c bus driver ignores the I2C_M_RECV_LEN flag (as some of them do), it is possible for an I2C_SMBUS_BLOCK_DATA read issued on some random device to return an arbitrary value in the first byte (and nothing else). When this happens, i2c_smbus_xfer_emulated() will happily write past the end of the supplied data buffer, thus causing Bad Things to happen. To prevent this, check the size before copying the data block and return an error if it is too large. Fixes: 209d27c3b167 ("i2c: Emulate SMBus block read over I2C") Signed-off-by: Mans Rullgard <mans@mansr.com> [wsa: use better errno] Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 40e05200593af06633f64ab0effff052eee6f076 ]

If the i2c bus driver ignores the I2C_M_RECV_LEN flag (as some of
them do), it is possible for an I2C_SMBUS_BLOCK_DATA read issued
on some random device to return an arbitrary value in the first
byte (and nothing else).  When this happens, i2c_smbus_xfer_emulated()
will happily write past the end of the supplied data buffer, thus
causing Bad Things to happen.  To prevent this, check the size
before copying the data block and return an error if it is too large.

Fixes: 209d27c3b167 ("i2c: Emulate SMBus block read over I2C")
Signed-off-by: Mans Rullgard <mans@mansr.com>
[wsa: use better errno]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: fsi: Fix the port number field in status register 2020-06-30T19:37:02+00:00 Eddie James eajames@linux.ibm.com 2020-06-09T20:15:54+00:00 4a6e6413059e8cbacb99ce797ec447612f407e43 [ Upstream commit 502035e284cc7e9efef22b01771d822d49698ab9 ] The port number field in the status register was not correct, so fix it. Fixes: d6ffb6300116 ("i2c: Add FSI-attached I2C master algorithm") Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 502035e284cc7e9efef22b01771d822d49698ab9 ]

The port number field in the status register was not correct, so fix it.

Fixes: d6ffb6300116 ("i2c: Add FSI-attached I2C master algorithm")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Revert "i2c: tegra: Fix suspending in active runtime PM state" 2020-06-30T19:36:47+00:00 Thierry Reding treding@nvidia.com 2020-04-30T11:31:58+00:00 8ae850cddf27b7b354b6abe207c5b7c05d615a53 [ Upstream commit 78ad73421831247e46c31899a7bead02740e4bef ] This reverts commit 9f42de8d4ec2304f10bbc51dc0484f3503d61196. It's not safe to use pm_runtime_force_{suspend,resume}(), especially during the noirq phase of suspend. See also the guidance provided in commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)"). Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 78ad73421831247e46c31899a7bead02740e4bef ]

This reverts commit 9f42de8d4ec2304f10bbc51dc0484f3503d61196.

It's not safe to use pm_runtime_force_{suspend,resume}(), especially
during the noirq phase of suspend. See also the guidance provided in
commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM
and system sleep (v2)").

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n 2020-06-24T15:50:41+00:00 Max Staudt max@enpas.org 2020-06-07T18:28:12+00:00 e1ee6238534e514268bc373f03fb398ac0c8a9d0 [ Upstream commit cdb555397f438592bab00599037c347b700cf397 ] This has been found by the Kernel Test Robot: http://lkml.iu.edu/hypermail/linux/kernel/2006.0/06862.html With CONFIG_AMIGA_PCMCIA=n, io_mm.h does not pull in amigahw.h and ZTWO_VADDR is undefined. Add forgotten include to i2c-icy.c Fixes: 4768e90ecaec ("i2c: Add i2c-icy for I2C on m68k/Amiga") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Max Staudt <max@enpas.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit cdb555397f438592bab00599037c347b700cf397 ]

This has been found by the Kernel Test Robot:
http://lkml.iu.edu/hypermail/linux/kernel/2006.0/06862.html

With CONFIG_AMIGA_PCMCIA=n, io_mm.h does not pull in amigahw.h and
ZTWO_VADDR is undefined. Add forgotten include to i2c-icy.c

Fixes: 4768e90ecaec ("i2c: Add i2c-icy for I2C on m68k/Amiga")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: pxa: fix i2c_pxa_scream_blue_murder() debug output 2020-06-24T15:50:24+00:00 Russell King rmk+kernel@armlinux.org.uk 2020-04-27T18:49:22+00:00 32a5bc992b6cf44ec658eb589b0dbe39e15ed197 [ Upstream commit 88b73ee7ca4c90baf136ed5a8377fc5a9b73ac08 ] The IRQ log output is supposed to appear on a single line. However, commit 3a2dc1677b60 ("i2c: pxa: Update debug function to dump more info on error") resulted in it being printed one-entry-per-line, which is excessively long. Fixing this is not a trivial matter; using pr_cont() doesn't work as the previous dev_dbg() may not have been compiled in, or may be dynamic. Since the rest of this function output is at error level, and is also debug output, promote this to error level as well to avoid this problem. Reduce the number of always zero prefix digits to save screen real- estate. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 88b73ee7ca4c90baf136ed5a8377fc5a9b73ac08 ]

The IRQ log output is supposed to appear on a single line.  However,
commit 3a2dc1677b60 ("i2c: pxa: Update debug function to dump more info
on error") resulted in it being printed one-entry-per-line, which is
excessively long.

Fixing this is not a trivial matter; using pr_cont() doesn't work as
the previous dev_dbg() may not have been compiled in, or may be
dynamic.

Since the rest of this function output is at error level, and is also
debug output, promote this to error level as well to avoid this
problem.

Reduce the number of always zero prefix digits to save screen real-
estate.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>