[ Upstream commit d52097010078c1844348dc0e467305e5f90fd317 ] The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16. It's better to have same data type in struct dw_scl_sda_cfg as well. Reported-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebe82cf92cd4825c3029434cabfcd2f1780e64be ] Current I2C reset procedure is broken in two ways: 1) It only generate 1 START instead of 9 STARTs and STOP. 2) It leaves the bus Busy so every I2C xfer after the first fixup calls the reset routine again, for every xfer there after. This fixes both errors. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Acked-by: Scott Wood <oss@buserror.net> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit effa453168a7eeb8a562ff4edc1dbf9067360a61 ] If an invalid block size is provided, reject it instead of silently changing it to a supported value. Especially critical I see the case of a write transfer with block length 0. In this case we have no guarantee that the byte we would write is valid. When silently reducing a read to 32 bytes then we don't return an error and the caller may falsely assume that we returned the full requested data. If this change should break any (broken) caller, then I think we should fix the caller. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02fe0fbd8a21e183687925c3a266ae27dda9840f ] In a typical read transfer, start completion flag is being set after read finishes (notice ipd bit 4 being set): trasnfer poll=0 i2c start rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10 i2c read rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b i2c stop rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33 This causes I2C transfer being aborted in polled mode from a stop completion handler: trasnfer poll=1 i2c start rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10 i2c read rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0 rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b i2c stop rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13 i2c stop rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10 Clearing the START flag after read fixes the issue without any obvious side effects. This issue was dicovered on RK3566 when adding support for powering off the RK817 PMIC. Signed-off-by: Ondrej Jirman <megous@megous.com> Reviewed-by: John Keeping <john@metanate.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58fb7c643d346e2364404554f531cfa6a1a3917c ]
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: ce38815d39ea ("I2C: mediatek: Add driver for MediaTek I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6840a5e370b7ea4fde16ce2caf431bcc87f9a75 ]
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec97853f ("i2c-s3c2410: Change IRQ to be plain integer.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1299505162ad00def3573260c2c68b9c8e8d697 ]
When adding the code to handle platform_get_irq*() errors in the commit
489447380a29 ("handle errors returned by platform_get_irq*()"), the
actual error code was enforced to be -ENXIO in the driver for some
strange reason. This didn't matter much until the deferred probing was
introduced -- which requires an actual error code to be propagated
upstream from the failure site.
While fixing this, also stop overriding the errors from request_irq() to
-EIO (done since the pre-git era).
Fixes: 489447380a29 ("[PATCH] handle errors returned by platform_get_irq*()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f16a3bb69aa6baabf8f0aca982c8cf21e2a4f6bc ]
The driver is written as if platform_get_irq() returns 0 on errors (while
actually it returns a negative error code), blithely passing these error
codes to request_irq() (which takes *unsigned* IRQ #) -- which fails with
-EINVAL. Add the necessary error check to the pre-existing *if* statement
forcing the driver into the polling mode...
Fixes: 4ad48e6ab18c ("i2c: Renesas Highlander FPGA SMBus support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 86ff25ed6cd8240d18df58930bd8848b19fce308 upstream. If an i2c driver happens to not provide the full amount of data that a user asks for, it is possible that some uninitialized data could be sent to userspace. While all in-kernel drivers look to be safe, just be sure by initializing the buffer to zero before it is passed to the i2c driver so that any future drivers will not have this issue. Also properly copy the amount of data recvieved to the userspace buffer, as pointed out by Dan Carpenter. Reported-by: Eric Dumazet <edumazet@google.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ca070ef0dd885616ef294d269a9bf8e3b258e1a upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the OSIFI2C_SET_BIT_RATE and OSIFI2C_STOP requests which erroneously
used the osif_usb_read() helper and set the IN direction bit.
Reported-by: syzbot+9d7dadd15b8819d73f41@syzkaller.appspotmail.com
Fixes: 83e53a8f120f ("i2c: Add bus driver for for OSIF USB i2c device.")
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>