linux-stable.git/drivers/i2c, branch v4.3.6 Linux kernel stable tree i2c: rcar: disable runtime PM correctly in slave mode 2016-02-19T22:28:29+00:00 Wolfram Sang wsa+renesas@sang-engineering.com 2015-12-16T19:05:18+00:00 e266f6c3b75c6b1695483685ab16f2cdb54e47ec commit b4cd08aa1f53c831e67dc5c6bc9f9acff27abcba upstream. When we also are I2C slave, we need to disable runtime PM because the address detection mechanism needs to be active all the time. However, we can reenable runtime PM once the slave instance was unregistered. So, use pm_runtime_get_sync/put to achieve this, since it has proper refcounting. pm_runtime_allow/forbid is like a global knob controllable from userspace which is unsuitable here. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit b4cd08aa1f53c831e67dc5c6bc9f9acff27abcba upstream.

When we also are I2C slave, we need to disable runtime PM because the
address detection mechanism needs to be active all the time. However, we
can reenable runtime PM once the slave instance was unregistered. So,
use pm_runtime_get_sync/put to achieve this, since it has proper
refcounting. pm_runtime_allow/forbid is like a global knob controllable
from userspace which is unsuitable here.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: rk3x: populate correct variable for sda_falling_time 2016-02-19T22:28:29+00:00 Wolfram Sang wsa@the-dreams.de 2015-11-25T15:58:18+00:00 42947fa48a86aca9e52a4003af69e6bb753dc7ea commit 9abd29e7c13de24ce73213a425d9574b35ac0c6a upstream. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 9abd29e7c13de24ce73213a425d9574b35ac0c6a upstream.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: mv64xxx: The n clockdiv factor is 0 based on sunxi SoCs 2016-02-19T22:28:29+00:00 Hans de Goede hdegoede@redhat.com 2015-09-27T14:57:08+00:00 226706fd3918ea3e42c31de2476df3e1155b9296 commit bba61f50f76574ca5b84b310925be7c2e8e64275 upstream. According to the datasheets the n factor for dividing the tclk is 2 to the power n on Allwinner SoCs, not 2 to the power n + 1 as it is on other mv64xxx implementations. I've contacted Allwinner about this and they have confirmed that the datasheet is correct. This commit fixes the clk-divider calculations for Allwinner SoCs accordingly. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Tested-by: Olliver Schinagl <oliver@schinagl.nl> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit bba61f50f76574ca5b84b310925be7c2e8e64275 upstream.

According to the datasheets the n factor for dividing the tclk is
2 to the power n on Allwinner SoCs, not 2 to the power n + 1 as it is
on other mv64xxx implementations.

I've contacted Allwinner about this and they have confirmed that the
datasheet is correct.

This commit fixes the clk-divider calculations for Allwinner SoCs
accordingly.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: fix wakeup irq parsing 2016-02-19T22:28:28+00:00 Grygorii Strashko grygorii.strashko@ti.com 2015-11-12T13:42:26+00:00 37afe551d4f1b234176ff5d38edb12cfef678fe5 commit c18fba23061f16dde128e10d4869ba4e88e0e81a upstream. This patch fixes obvious copy-past error in wake up irq parsing code which leads to the fact that dev_pm_set_wake_irq() will be called with wrong IRQ number when "wakeup" IRQ is not defined in DT. Fixes: 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c18fba23061f16dde128e10d4869ba4e88e0e81a upstream.

This patch fixes obvious copy-past error in wake up irq parsing
code which leads to the fact that dev_pm_set_wake_irq() will
be called with wrong IRQ number when "wakeup" IRQ is not
defined in DT.

Fixes: 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: at91: manage unexpected RXRDY flag when starting a transfer 2016-02-19T22:28:28+00:00 Ludovic Desroches ludovic.desroches@atmel.com 2015-10-26T09:38:27+00:00 6868ec4d4d0a54e0627dd562cb357e23c69edd43 commit a9bed6b10bd117a300cceb9062003f7a2761ef99 upstream. In some cases, we could start a new i2c transfer with the RXRDY flag set. It is not a clean state and it leads to print annoying error messages even if there no real issue. The cause is only having garbage data in the Receive Holding Register because of a weird behavior of the RXRDY flag. Reported-by: Peter Rosin <peda@lysator.liu.se> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Tested-by: Peter Rosin <peda@lysator.liu.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Fixes: 93563a6a71bb ("i2c: at91: fix a race condition when using the DMA controller") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a9bed6b10bd117a300cceb9062003f7a2761ef99 upstream.

In some cases, we could start a new i2c transfer with the RXRDY flag
set. It is not a clean state and it leads to print annoying error
messages even if there no real issue. The cause is only having garbage
data in the Receive Holding Register because of a weird behavior of the
RXRDY flag.

Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71bb ("i2c: at91: fix a race condition when using the DMA controller")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: at91: fix write transfers by clearing pending interrupt first 2016-02-19T22:28:28+00:00 Cyrille Pitchen cyrille.pitchen@atmel.com 2015-10-21T13:44:03+00:00 806bac9faf482eb27e9d9f936480a6ff5ab309f2 commit 6f6ddbb09d2a5baded0e23add3ad2d9e9417ab30 upstream. In some cases a NACK interrupt may be pending in the Status Register (SR) as a result of a previous transfer. However at91_do_twi_transfer() did not read the SR to clear pending interruptions before starting a new transfer. Hence a NACK interrupt rose as soon as it was enabled again at the I2C controller level, resulting in a wrong sequence of operations and strange patterns of behaviour on the I2C bus, such as a clock stretch followed by a restart of the transfer. This first issue occurred with both DMA and PIO write transfers. Also when a NACK error was detected during a PIO write transfer, the interrupt handler used to wrongly start a new transfer by writing into the Transmit Holding Register (THR). Then the I2C slave was likely to reply with a second NACK. This second issue is fixed in atmel_twi_interrupt() by handling the TXRDY status bit only if both the TXCOMP and NACK status bits are cleared. Tested with a at24 eeprom on sama5d36ek board running a linux-4.1-at91 kernel image. Adapted to linux-next. Reported-by: Peter Rosin <peda@lysator.liu.se> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Tested-by: Peter Rosin <peda@lysator.liu.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Fixes: 93563a6a71bb ("i2c: at91: fix a race condition when using the DMA controller") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 6f6ddbb09d2a5baded0e23add3ad2d9e9417ab30 upstream.

In some cases a NACK interrupt may be pending in the Status Register (SR)
as a result of a previous transfer. However at91_do_twi_transfer() did not
read the SR to clear pending interruptions before starting a new transfer.
Hence a NACK interrupt rose as soon as it was enabled again at the I2C
controller level, resulting in a wrong sequence of operations and strange
patterns of behaviour on the I2C bus, such as a clock stretch followed by
a restart of the transfer.

This first issue occurred with both DMA and PIO write transfers.

Also when a NACK error was detected during a PIO write transfer, the
interrupt handler used to wrongly start a new transfer by writing into the
Transmit Holding Register (THR). Then the I2C slave was likely to reply
with a second NACK.

This second issue is fixed in atmel_twi_interrupt() by handling the TXRDY
status bit only if both the TXCOMP and NACK status bits are cleared.

Tested with a at24 eeprom on sama5d36ek board running a linux-4.1-at91
kernel image. Adapted to linux-next.

Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71bb ("i2c: at91: fix a race condition when using the DMA controller")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: pnx: fix runtime warnings caused by enabling unprepared clock 2015-10-23T20:26:28+00:00 Vladimir Zapolskiy vz@mleia.com 2015-10-17T18:52:27+00:00 5dd32eae604ee503e5a84a4f18d1381e4cc356cb The driver can not be used on a platform with common clock framework until clk_prepare/clk_unprepare calls are added, otherwise clk_enable calls will fail and a WARN is generated. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> 
The driver can not be used on a platform with common clock framework
until clk_prepare/clk_unprepare calls are added, otherwise clk_enable
calls will fail and a WARN is generated.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c: mv64xxx: really allow I2C offloading 2015-10-22T12:47:45+00:00 Hezi Shahmoon hezi@marvell.com 2015-10-20T14:32:24+00:00 0729a04977d497cf66234fd7f900ddcec3ef1c52 Commit 00d8689b85a7 ("i2c: mv64xxx: rework offload support to fix several problems") completely reworked the offload support, but left a debugging-related "return false" at the beginning of the mv64xxx_i2c_can_offload() function. This has the unfortunate consequence that offloading is in fact never used, which wasn't really the intention. This commit fixes that problem by removing the bogus "return false". Fixes: 00d8689b85a7 ("i2c: mv64xxx: rework offload support to fix several problems") Signed-off-by: Hezi Shahmoon <hezi@marvell.com> [Thomas: reworked commit log and title.] Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: <stable@vger.kernel.org> 
Commit 00d8689b85a7 ("i2c: mv64xxx: rework offload support to fix
several problems") completely reworked the offload support, but left a
debugging-related "return false" at the beginning of the
mv64xxx_i2c_can_offload() function. This has the unfortunate consequence
that offloading is in fact never used, which wasn't really the
intention.

This commit fixes that problem by removing the bogus "return false".

Fixes: 00d8689b85a7 ("i2c: mv64xxx: rework offload support to fix several problems")
Signed-off-by: Hezi Shahmoon <hezi@marvell.com>
[Thomas: reworked commit log and title.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org>
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348 2015-10-18T12:11:08+00:00 Mika Westerberg mika.westerberg@linux.intel.com 2015-09-24T09:06:54+00:00 56d4b8a24cef5d66f0d10ac778a520d3c2c68a48 ACPI SSCN/FMCN methods were originally added because then the platform can provide the most accurate HCNT/LCNT values to the driver. However, this seems not to be true for Dell Inspiron 7348 where using these causes the touchpad to fail in boot: i2c_hid i2c-DLL0675:00: failed to retrieve report from device. i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration i2c_hid i2c-DLL0675:00: failed to retrieve report from device. i2c_designware INT3433:00: controller timed out The values received from ACPI are (in fast mode): HCNT: 72 LCNT: 160 this translates to following timings (input clock is 100MHz on Broadwell): tHIGH: 720 ns (spec min 600 ns) tLOW: 1600 ns (spec min 1300 ns) Bus period: 2920 ns (assuming 300 ns tf and tr) Bus speed: 342.5 kHz Both tHIGH and tLOW are within the I2C specification. The calculated values when ACPI parameters are not used are (in fast mode): HCNT: 87 LCNT: 159 which translates to: tHIGH: 870 ns (spec min 600 ns) tLOW: 1590 ns (spec min 1300 ns) Bus period 3060 ns (assuming 300 ns tf and tr) Bus speed 326.8 kHz These values are also within the I2C specification. Since both ACPI and calculated values meet the I2C specification timing requirements it is hard to say why the touchpad does not function properly with the ACPI values except that the bus speed is higher in this case (but still well below the max 400kHz). Solve this by adding DMI quirk to the driver that disables using ACPI parameters on this particulare machine. Reported-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org 
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:

  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: controller timed out

The values received from ACPI are (in fast mode):

  HCNT: 72
  LCNT: 160

this translates to following timings (input clock is 100MHz on Broadwell):

  tHIGH: 720 ns (spec min 600 ns)
  tLOW: 1600 ns (spec min 1300 ns)
  Bus period: 2920 ns (assuming 300 ns tf and tr)
  Bus speed: 342.5 kHz

Both tHIGH and tLOW are within the I2C specification.

The calculated values when ACPI parameters are not used are (in fast mode):

  HCNT: 87
  LCNT: 159

which translates to:

  tHIGH: 870 ns (spec min 600 ns)
  tLOW: 1590 ns (spec min 1300 ns)
  Bus period 3060 ns (assuming 300 ns tf and tr)
  Bus speed 326.8 kHz

These values are also within the I2C specification.

Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).

Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.

Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
i2c: designware-platdrv: enable RuntimePM before registering to the core 2015-10-15T12:28:07+00:00 Wolfram Sang wsa+renesas@sang-engineering.com 2015-10-09T09:39:24+00:00 36d48fb5766aee9717e429f772046696b215282d The core may register clients attached to this master which may use funtionality from the master. So, RuntimePM must be enabled before, otherwise this will fail. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable@kernel.org 
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@kernel.org