During ipmi stress tests we see occasional failure of transactions at the boot time. This happens in the case of a I2C_M_RECV_LEN transactions, when the read transfer completes (with the initial read length of 34) before the driver gets a chance to handle interrupts. The current driver code expects at least 2 interrupts for I2C_M_RECV_LEN transactions. The length is updated during the first interrupt, and the buffer contents are only copied during subsequent interrupts. In case of just one interrupt, we will complete the transaction without copying out the bytes from RX fifo. Update the code to drain the RX fifo after the length update, so that the transaction completes correctly in all cases. Signed-off-by: George Cherian <george.cherian@cavium.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Pull locking fixes from Ingo Molnar: "A paravirt UP-patching fix, and an I2C MUX driver lockdep warning fix" * 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: locking/pvqspinlock/x86: Use LOCK_PREFIX in __pv_queued_spin_unlock() assembly code i2c/mux, locking/core: Annotate the nested rt_mutex usage locking/rtmutex: Allow specifying a subclass for nested locking
If an i2c topology has instances of nested muxes, then a lockdep splat
is produced when when i2c_parent_lock_bus() is called. Here is an
example:
============================================
WARNING: possible recursive locking detected
--------------------------------------------
insmod/68159 is trying to acquire lock:
(i2c_register_adapter#2){+.+.}, at: i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
but task is already holding lock:
(i2c_register_adapter#2){+.+.}, at: i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(i2c_register_adapter#2);
lock(i2c_register_adapter#2);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by insmod/68159:
#0: (i2c_register_adapter#2){+.+.}, at: i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
stack backtrace:
CPU: 13 PID: 68159 Comm: insmod Tainted: G O
Call Trace:
dump_stack+0x67/0x98
__lock_acquire+0x162e/0x1780
lock_acquire+0xba/0x200
rt_mutex_lock+0x44/0x60
i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
i2c_parent_lock_bus+0x3e/0x50 [i2c_mux]
i2c_smbus_xfer+0xf0/0x700
i2c_smbus_read_byte+0x42/0x70
my2c_init+0xa2/0x1000 [my2c]
do_one_initcall+0x51/0x192
do_init_module+0x62/0x216
load_module+0x20f9/0x2b50
SYSC_init_module+0x19a/0x1c0
SyS_init_module+0xe/0x10
do_syscall_64+0x6c/0x1a0
entry_SYSCALL_64_after_hwframe+0x42/0xb7
Reported-by: John Sperbeck <jsperbeck@google.com>
Tested-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Deepa Dinamani <deepadinamani@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Chang <dpf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Link: http://lkml.kernel.org/r/20180720083914.1950-3-peda@axentia.se
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I2C is open drain, so request the GPIO accordingly, even if pinmux did set it up correctly for in-kernel users in this case. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Gen3, we can only do RXDMA once per transfer reliably. For that, we must reset the device, then we can have RXDMA once. This patch implements this. When there is no reset controller or the reset fails, RXDMA will be blocked completely. Otherwise, it will be disabled after the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu Yamasaki, yet completely refactored to handle multiple read messages within one transfer. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Make sure to call reinit_completion() before dma is started to avoid race
condition where reinit_completion() is called after complete() and before
wait_for_completion_timeout().
Signed-off-by: Esben Haabendal <eha@deif.com>
Fixes: ce1a78840ff7 ("i2c: imx: add DMA support for freescale i2c driver")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If CLKH is set to 0 I2C clock is not generated at all, so avoid this value and stretch the clock in this case. Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang: - I2C core bugfix regarding bus recovery - driver bugfix for the tegra driver - typo correction * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: recovery: if possible send STOP with recovery pulses i2c: tegra: Fix NACK error handling i2c: stu300: use non-archaic spelling of failes
I2C clients may misunderstand recovery pulses if they can't read SDA to bail out early. In the worst case, as a write operation. To avoid that and if we can write SDA, try to send STOP to avoid the misinterpretation. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
On Tegra30 Cardhu the PCA9546 I2C mux is not ACK'ing I2C commands on
resume from suspend (which is caused by the reset signal for the I2C
mux not being configured correctl). However, this NACK is causing the
Tegra30 to hang on resuming from suspend which is not expected as we
detect NACKs and handle them. The hang observed appears to occur when
resetting the I2C controller to recover from the NACK.
Commit 77821b4678f9 ("i2c: tegra: proper handling of error cases") added
additional error handling for some error cases including NACK, however,
it appears that this change conflicts with an early fix by commit
f70893d08338 ("i2c: tegra: Add delay before resetting the controller
after NACK"). After commit 77821b4678f9 was made we now disable 'packet
mode' before the delay from commit f70893d08338 happens. Testing shows
that moving the delay to before disabling 'packet mode' fixes the hang
observed on Tegra30. The delay was added to give the I2C controller
chance to send a stop condition and so it makes sense to move this to
before we disable packet mode. Please note that packet mode is always
enabled for Tegra.
Fixes: 77821b4678f9 ("i2c: tegra: proper handling of error cases")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org