linux-stable.git/drivers/i2c, branch v3.16.52

i2c: ismt: Separate I2C block read from SMBus block read

2017-11-11T13:34:04+00:00

commit c6ebcedbab7ca78984959386012a17b21183e1a3 upstream.

Commit b6c159a9cb69 ("i2c: ismt: Don't duplicate the receive length for
block reads") broke I2C block reads. It aimed to fix normal SMBus block
read, but changed the correct behavior of I2C block read in the process.

According to Documentation/i2c/smbus-protocol, one vital difference
between normal SMBus block read and I2C block read is that there is no
byte count prefixed in the data sent on the wire:

 SMBus Block Read:  i2c_smbus_read_block_data()
 S Addr Wr [A] Comm [A]
            S Addr Rd [A] [Count] A [Data] A [Data] A ... A [Data] NA P

 I2C Block Read:  i2c_smbus_read_i2c_block_data()
 S Addr Wr [A] Comm [A]
            S Addr Rd [A] [Data] A [Data] A ... A [Data] NA P

Therefore the two transaction types need to be processed differently in
the driver by copying of the dma_buffer as done previously for the
I2C_SMBUS_I2C_BLOCK_DATA case.

Fixes: b6c159a9cb69 ("i2c: ismt: Don't duplicate the receive length for block reads")
Signed-off-by: Pontus Andersson 
Tested-by: Stephen Douthit 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: ismt: Return EMSGSIZE for block reads with bogus length

2017-11-11T13:33:33+00:00

commit ba201c4f5ebe13d7819081756378777d8153f23e upstream.

Compare the number of bytes actually seen on the wire to the byte
count field returned by the slave device.

Previously we just overwrote the byte count returned by the slave
with the real byte count and let the caller figure out if the
message was sane.

Signed-off-by: Stephen Douthit 
Tested-by: Dan Priamo 
Acked-by: Neil Horman 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: ismt: Don't duplicate the receive length for block reads

2017-11-11T13:33:33+00:00

commit b6c159a9cb69c2cf0bf59d4e12c3a2da77e4d994 upstream.

According to Table 15-14 of the C2000 EDS (Intel doc #510524) the
rx data pointed to by the descriptor dptr contains the byte count.

desc->rxbytes reports all bytes read on the wire, including the
"byte count" byte.  So if a device sends 4 bytes in response to a
block read, on the wire and in the DMA buffer we see:

count data1 data2 data3 data4
 0x04  0xde  0xad  0xbe  0xef

That's what we want to return in data->block to the next level.

Instead we were actually prefixing that with desc->rxbytes:

bad
count count data1 data2 data3 data4
 0x05  0x04  0xde  0xad  0xbe  0xef

This was discovered while developing a BMC solution relying on the
ipmi_ssif.c driver which was trying to interpret the bogus length
field as part of the IPMI response.

Signed-off-by: Stephen Douthit 
Tested-by: Dan Priamo 
Acked-by: Neil Horman 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: mux: pinctrl: mention correct module name in Kconfig help text

2017-11-11T13:32:57+00:00

commit d1510a2e5ab6cb3a67f1c55ca5e7a6d2c6dec340 upstream.

Kconfig says the resulting module is pinctrl-i2cmux, but the module when
built is i2c-mux-pinctrl.

Fixes: ae58d1e40698 ("i2c: Add generic I2C multiplexer using pinctrl API")
Signed-off-by: Chris Gorman 
Signed-off-by: Peter Rosin 
Signed-off-by: Ben Hutchings

i2c: cadance: fix ctrl/addr reg write order

2017-10-12T14:27:52+00:00

commit 8064c616984eaa015f018dba595d78cd24a0cc8c upstream.

The driver was clearing the hold bit in the control register before
writing to the address register which resulted in a stop condition
being generated rather than a repeated start.

This issue was only observed when a system was running much
slower than a normal processor would execute.  The IP data sheet
mentions a ordering of writing to the address register before
clearing the hold.

Fixes: df8eb5691c4 ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: John Linn 
Signed-off-by: Paresh Chaudhary 
Signed-off-by: Matthew Weber 
Signed-off-by: Wolfram Sang 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

i2c: imx: Use correct function to write to register

2017-09-15T17:30:14+00:00

commit 6c782a5ea56a799658e213a78dc1455264938afa upstream.

The i2c-imx driver incorrectly uses readb()/writeb() to read and
write to the appropriate registers when performing a repeated start.
The appropriate imx_i2c_read_reg()/imx_i2c_write_reg() functions
should be used instead. Performing a repeated start results in
a kernel panic. The platform is imx.

Signed-off-by: Michail G Etairidis 
Fixes: ce1a78840ff7 ("i2c: imx: add DMA support for freescale i2c driver")
Fixes: 054b62d9f25c ("i2c: imx: fix the i2c bus hang issue when do repeat restart")
Acked-by: Fugang Duan 
Acked-by: Uwe Kleine-König 
Signed-off-by: Wolfram Sang 
[bwh: Backported to 3.16: drop changes in i2c_imx_dma_read()]
Signed-off-by: Ben Hutchings

i2c: ismt: fix wrong device address when unmap the data buffer

2017-09-15T17:30:11+00:00

commit 17e83549e199d89aace7788a9f11c108671eecf5 upstream.

Fix the following kernel bug:

kernel BUG at drivers/iommu/intel-iommu.c:3260!
invalid opcode: 0000 [#5] PREEMPT SMP
Hardware name: Intel Corp. Harcuvar/Server, BIOS HAVLCRB0.X64.0013.D39.1608311820 08/31/2016
task: ffff880175389950 ti: ffff880176bec000 task.ti: ffff880176bec000
RIP: 0010:[]  [] intel_unmap+0x25b/0x260
RSP: 0018:ffff880176bef5e8  EFLAGS: 00010296
RAX: 0000000000000024 RBX: ffff8800773c7c88 RCX: 000000000000ce04
RDX: 0000000080000000 RSI: 0000000000000000 RDI: 0000000000000009
RBP: ffff880176bef638 R08: 0000000000000010 R09: 0000000000000004
R10: ffff880175389c78 R11: 0000000000000a4f R12: ffff8800773c7868
R13: 00000000ffffac88 R14: ffff8800773c7818 R15: 0000000000000001
FS:  00007fef21258700(0000) GS:ffff88017b5c0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000066d6d8 CR3: 000000007118c000 CR4: 00000000003406e0
Stack:
 00000000ffffac88 ffffffff8199867f ffff880176bef5f8 ffff880100000030
 ffff880176bef668 ffff8800773c7c88 ffff880178288098 ffff8800772c0010
 ffff8800773c7818 0000000000000001 ffff880176bef648 ffffffff8150a86e
Call Trace:
 [] ? printk+0x46/0x48
 [] intel_unmap_page+0xe/0x10
 [] ismt_access+0x27b/0x8fa [i2c_ismt]
 [] ? __pm_runtime_suspend+0xa0/0xa0
 [] ? pm_suspend_timer_fn+0x80/0x80
 [] ? __pm_runtime_suspend+0xa0/0xa0
 [] ? pm_suspend_timer_fn+0x80/0x80
 [] ? pci_bus_read_dev_vendor_id+0xf0/0xf0
 [] i2c_smbus_xfer+0xec/0x4b0
 [] ? vprintk_emit+0x345/0x530
 [] i2cdev_ioctl_smbus+0x12b/0x240 [i2c_dev]
 [] ? vprintk_default+0x29/0x40
 [] i2cdev_ioctl+0x63/0x1ec [i2c_dev]
 [] do_vfs_ioctl+0x328/0x5d0
 [] ? vfs_write+0x11c/0x190
 [] ? rt_up_read+0x19/0x20
 [] SyS_ioctl+0x81/0xa0
 [] system_call_fastpath+0x16/0x6e

This happen When run "i2cdetect -y 0" detect SMBus iSMT adapter.

After finished I2C block read/write, when unmap the data buffer,
a wrong device address was pass to dma_unmap_single().

To fix this, give dma_unmap_single() the "dev" parameter, just like
what dma_map_single() does, then unmap can find the right devices.

Fixes: 13f35ac14cd0 ("i2c: Adding support for Intel iSMT SMBus 2.0 host controller")
Signed-off-by: Liwei Song 
Reviewed-by: Andy Shevchenko 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: i2c-tiny-usb: fix buffer not being DMA capable

2017-09-15T17:29:48+00:00

commit 5165da5923d6c7df6f2927b0113b2e4d9288661e upstream.

Since v4.9 i2c-tiny-usb generates the below call trace
and longer works, since it can't communicate with the
USB device. The reason is, that since v4.9 the USB
stack checks, that the buffer it should transfer is DMA
capable. This was a requirement since v2.2 days, but it
usually worked nevertheless.

[   17.504959] ------------[ cut here ]------------
[   17.505488] WARNING: CPU: 0 PID: 93 at drivers/usb/core/hcd.c:1587 usb_hcd_map_urb_for_dma+0x37c/0x570
[   17.506545] transfer buffer not dma capable
[   17.507022] Modules linked in:
[   17.507370] CPU: 0 PID: 93 Comm: i2cdetect Not tainted 4.11.0-rc8+ #10
[   17.508103] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
[   17.509039] Call Trace:
[   17.509320]  ? dump_stack+0x5c/0x78
[   17.509714]  ? __warn+0xbe/0xe0
[   17.510073]  ? warn_slowpath_fmt+0x5a/0x80
[   17.510532]  ? nommu_map_sg+0xb0/0xb0
[   17.510949]  ? usb_hcd_map_urb_for_dma+0x37c/0x570
[   17.511482]  ? usb_hcd_submit_urb+0x336/0xab0
[   17.511976]  ? wait_for_completion_timeout+0x12f/0x1a0
[   17.512549]  ? wait_for_completion_timeout+0x65/0x1a0
[   17.513125]  ? usb_start_wait_urb+0x65/0x160
[   17.513604]  ? usb_control_msg+0xdc/0x130
[   17.514061]  ? usb_xfer+0xa4/0x2a0
[   17.514445]  ? __i2c_transfer+0x108/0x3c0
[   17.514899]  ? i2c_transfer+0x57/0xb0
[   17.515310]  ? i2c_smbus_xfer_emulated+0x12f/0x590
[   17.515851]  ? _raw_spin_unlock_irqrestore+0x11/0x20
[   17.516408]  ? i2c_smbus_xfer+0x125/0x330
[   17.516876]  ? i2c_smbus_xfer+0x125/0x330
[   17.517329]  ? i2cdev_ioctl_smbus+0x1c1/0x2b0
[   17.517824]  ? i2cdev_ioctl+0x75/0x1c0
[   17.518248]  ? do_vfs_ioctl+0x9f/0x600
[   17.518671]  ? vfs_write+0x144/0x190
[   17.519078]  ? SyS_ioctl+0x74/0x80
[   17.519463]  ? entry_SYSCALL_64_fastpath+0x1e/0xad
[   17.519959] ---[ end trace d047c04982f5ac50 ]---

Signed-off-by: Sebastian Reichel 
Reviewed-by: Greg Kroah-Hartman 
Acked-by: Till Harbaum 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: riic: correctly finish transfers

2017-06-05T20:17:06+00:00

commit 71ccea095ea1d4efd004dab971be6d599e06fc3f upstream.

This fixes the condition where the controller has not fully completed its
final transfer and leaves the bus and controller in a undesirable state.

At the end of the last transmitted byte, the existing driver would just
signal for a STOP condition to be transmitted then immediately signal
completion. However, the full STOP procedure might not have fully taken
place by the time the runtime PM shuts off the peripheral clock, leaving
the bus in a suspended state.

Alternatively, the STOP condition on the bus may have completed, but when
the next transaction is requested by the upper layer, not all the
necessary register cleanup was finished from the last transfer which made
the driver return BUS BUSY when it really wasn't.

This patch now makes all transmit and receive transactions wait for the
STOP condition to fully complete before signaling a completed transaction.
With this new method, runtime PM no longer seems to be an issue.

Fixes: 310c18a41450 ("i2c: riic: add driver")
Signed-off-by: Chris Brandt 
Reviewed-by: Wolfram Sang 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: fix kernel memory disclosure in dev interface

2017-03-16T02:26:58+00:00

commit 30f939feaeee23e21391cfc7b484f012eb189c3c upstream.

i2c_smbus_xfer() does not always fill an entire block, allowing
kernel stack memory disclosure through the temp variable. Clear
it before it's read to.

Signed-off-by: Vlad Tsyrklevich 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings