linux-stable.git/drivers/hwmon, branch v5.4.151

hwmon: (tmp421) fix rounding for negative values

2021-10-06T13:42:33+00:00

[ Upstream commit 724e8af85854c4d3401313b6dd7d79cf792d8990 ]

Old code produces -24999 for 0b1110011100000000 input in standard format due to
always rounding up rather than "away from zero".

Use the common macro for division, unify and simplify the conversion code along
the way.

Fixes: 9410700b881f ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser 
Link: https://lore.kernel.org/r/20210924093011.26083-3-fercerpav@gmail.com
Signed-off-by: Guenter Roeck 
Signed-off-by: Sasha Levin

hwmon: (tmp421) report /PVLD condition as fault

2021-10-06T13:42:33+00:00

[ Upstream commit 540effa7f283d25bcc13c0940d808002fee340b8 ]

For both local and remote sensors all the supported ICs can report an
"undervoltage lockout" condition which means the conversion wasn't
properly performed due to insufficient power supply voltage and so the
measurement results can't be trusted.

Fixes: 9410700b881f ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser 
Link: https://lore.kernel.org/r/20210924093011.26083-2-fercerpav@gmail.com
Signed-off-by: Guenter Roeck 
Signed-off-by: Sasha Levin

hwmon: (mlxreg-fan) Return non-zero value when fan current state is enforced from sysfs

2021-10-06T13:42:32+00:00

[ Upstream commit e6fab7af6ba1bc77c78713a83876f60ca7a4a064 ]

Fan speed minimum can be enforced from sysfs. For example, setting
current fan speed to 20 is used to enforce fan speed to be at 100%
speed, 19 - to be not below 90% speed, etcetera. This feature provides
ability to limit fan speed according to some system wise
considerations, like absence of some replaceable units or high system
ambient temperature.

Request for changing fan minimum speed is configuration request and can
be set only through 'sysfs' write procedure. In this situation value of
argument 'state' is above nominal fan speed maximum.

Return non-zero code in this case to avoid
thermal_cooling_device_stats_update() call, because in this case
statistics update violates thermal statistics table range.
The issues is observed in case kernel is configured with option
CONFIG_THERMAL_STATISTICS.

Here is the trace from KASAN:
[  159.506659] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x7d/0xb0
[  159.516016] Read of size 4 at addr ffff888116163840 by task hw-management.s/7444
[  159.545625] Call Trace:
[  159.548366]  dump_stack+0x92/0xc1
[  159.552084]  ? thermal_cooling_device_stats_update+0x7d/0xb0
[  159.635869]  thermal_zone_device_update+0x345/0x780
[  159.688711]  thermal_zone_device_set_mode+0x7d/0xc0
[  159.694174]  mlxsw_thermal_modules_init+0x48f/0x590 [mlxsw_core]
[  159.700972]  ? mlxsw_thermal_set_cur_state+0x5a0/0x5a0 [mlxsw_core]
[  159.731827]  mlxsw_thermal_init+0x763/0x880 [mlxsw_core]
[  160.070233] RIP: 0033:0x7fd995909970
[  160.074239] Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ..
[  160.095242] RSP: 002b:00007fff54f5d938 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[  160.103722] RAX: ffffffffffffffda RBX: 0000000000000013 RCX: 00007fd995909970
[  160.111710] RDX: 0000000000000013 RSI: 0000000001906008 RDI: 0000000000000001
[  160.119699] RBP: 0000000001906008 R08: 00007fd995bc9760 R09: 00007fd996210700
[  160.127687] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000013
[  160.135673] R13: 0000000000000001 R14: 00007fd995bc8600 R15: 0000000000000013
[  160.143671]
[  160.145338] Allocated by task 2924:
[  160.149242]  kasan_save_stack+0x19/0x40
[  160.153541]  __kasan_kmalloc+0x7f/0xa0
[  160.157743]  __kmalloc+0x1a2/0x2b0
[  160.161552]  thermal_cooling_device_setup_sysfs+0xf9/0x1a0
[  160.167687]  __thermal_cooling_device_register+0x1b5/0x500
[  160.173833]  devm_thermal_of_cooling_device_register+0x60/0xa0
[  160.180356]  mlxreg_fan_probe+0x474/0x5e0 [mlxreg_fan]
[  160.248140]
[  160.249807] The buggy address belongs to the object at ffff888116163400
[  160.249807]  which belongs to the cache kmalloc-1k of size 1024
[  160.263814] The buggy address is located 64 bytes to the right of
[  160.263814]  1024-byte region [ffff888116163400, ffff888116163800)
[  160.277536] The buggy address belongs to the page:
[  160.282898] page:0000000012275840 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888116167000 pfn:0x116160
[  160.294872] head:0000000012275840 order:3 compound_mapcount:0 compound_pincount:0
[  160.303251] flags: 0x200000000010200(slab|head|node=0|zone=2)
[  160.309694] raw: 0200000000010200 ffffea00046f7208 ffffea0004928208 ffff88810004dbc0
[  160.318367] raw: ffff888116167000 00000000000a0006 00000001ffffffff 0000000000000000
[  160.327033] page dumped because: kasan: bad access detected
[  160.333270]
[  160.334937] Memory state around the buggy address:
[  160.356469] >ffff888116163800: fc ..

Fixes: 65afb4c8e7e4 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Vadim Pasternak 
Link: https://lore.kernel.org/r/20210916183151.869427-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck 
Signed-off-by: Sasha Levin

hwmon: (w83791d) Fix NULL pointer dereference by removing unnecessary structure field

2021-10-06T13:42:31+00:00

commit 943c15ac1b84d378da26bba41c83c67e16499ac4 upstream.

If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().

The patch fixes possible NULL pointer dereference by removing lm75[].

Found by Linux Driver Verification project (linuxtesting.org).

Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova 
Link: https://lore.kernel.org/r/20210921155153.28098-1-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignment]
Signed-off-by: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman

hwmon: (w83792d) Fix NULL pointer dereference by removing unnecessary structure field

2021-10-06T13:42:30+00:00

commit 0f36b88173f028e372668ae040ab1a496834d278 upstream.

If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().

The patch fixes possible NULL pointer dereference by removing lm75[].

Found by Linux Driver Verification project (linuxtesting.org).

Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova 
Link: https://lore.kernel.org/r/20210921155153.28098-2-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multipline alignment]
Signed-off-by: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman

hwmon: (w83793) Fix NULL pointer dereference by removing unnecessary structure field

2021-10-06T13:42:30+00:00

commit dd4d747ef05addab887dc8ff0d6ab9860bbcd783 upstream.

If driver read tmp value sufficient for
(tmp & 0x08) && (!(tmp & 0x80)) && ((tmp & 0x7) == ((tmp >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().

The patch fixes possible NULL pointer dereference by removing lm75[].

Found by Linux Driver Verification project (linuxtesting.org).

Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova 
Link: https://lore.kernel.org/r/20210921155153.28098-3-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignments]
Signed-off-by: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman

hwmon: (max31790) Fix fan speed reporting for fan7..12

2021-07-14T14:53:23+00:00

[ Upstream commit cbbf244f0515af3472084f22b6213121b4a63835 ]

Fans 7..12 do not have their own set of configuration registers.
So far the code ignored that and read beyond the end of the configuration
register range to get the tachometer period. This resulted in more or less
random fan speed values for those fans.

The datasheet is quite vague when it comes to defining the tachometer
period for fans 7..12. Experiments confirm that the period is the same
for both fans associated with a given set of configuration registers.

Fixes: 54187ff9d766 ("hwmon: (max31790) Convert to use new hwmon registration API")
Fixes: 195a4b4298a7 ("hwmon: Driver for Maxim MAX31790")
Cc: Jan Kundrát 
Reviewed-by: Jan Kundrát 
Cc: Václav Kubernát 
Reviewed-by: Jan Kundrát 
Signed-off-by: Guenter Roeck 
Link: https://lore.kernel.org/r/20210526154022.3223012-2-linux@roeck-us.net
Signed-off-by: Sasha Levin

hwmon: (max31722) Remove non-standard ACPI device IDs

2021-07-14T14:53:23+00:00

[ Upstream commit 97387c2f06bcfd79d04a848d35517b32ee6dca7c ]

Valid Maxim Integrated ACPI device IDs would start with MXIM,
not with MAX1. On top of that, ACPI device IDs reflecting chip names
are almost always invalid.

Remove the invalid ACPI IDs.

Fixes: 04e1e70afec6 ("hwmon: (max31722) Add support for MAX31722/MAX31723 temperature sensors")
Signed-off-by: Guenter Roeck 
Signed-off-by: Sasha Levin

hwmon: (max31790) Fix pwmX_enable attributes

2021-07-14T14:53:14+00:00

[ Upstream commit 148c847c9e5a54b99850617bf9c143af9a344f92 ]

pwmX_enable supports three possible values:

0: Fan control disabled. Duty cycle is fixed to 0%
1: Fan control enabled, pwm mode. Duty cycle is determined by
   values written into Target Duty Cycle registers.
2: Fan control enabled, rpm mode
   Duty cycle is adjusted such that fan speed matches
   the values in Target Count registers

The current code does not do this; instead, it mixes pwm control
configuration with fan speed monitoring configuration. Worse, it
reports that pwm control would be disabled (pwmX_enable==0) when
it is in fact enabled in pwm mode. Part of the problem may be that
the chip sets the "TACH input enable" bit on its own whenever the
mode bit is set to RPM mode, but that doesn't mean that "TACH input
enable" accurately reflects the pwm mode.

Fix it up and only handle pwm control with the pwmX_enable attributes.
In the documentation, clarify that disabling pwm control (pwmX_enable=0)
sets the pwm duty cycle to 0%. In the code, explain why TACH_INPUT_EN
is set together with RPM_MODE.

While at it, only update the configuration register if the configuration
has changed, and only update the cached configuration if updating the
chip configuration was successful.

Cc: Jan Kundrát 
Cc: Václav Kubernát 
Signed-off-by: Guenter Roeck 
Tested-by: Václav Kubernát 
Reviewed-by: Jan Kundrát 
Link: https://lore.kernel.org/r/20210526154022.3223012-4-linux@roeck-us.net
Signed-off-by: Sasha Levin

hwmon: (max31790) Report correct current pwm duty cycles

2021-07-14T14:53:14+00:00

[ Upstream commit 897f6339893b741a5d68ae8e2475df65946041c2 ]

The MAX31790 has two sets of registers for pwm duty cycles, one to request
a duty cycle and one to read the actual current duty cycle. Both do not
have to be the same.

When reporting the pwm duty cycle to the user, the actual pwm duty cycle
from pwm duty cycle registers needs to be reported. When setting it, the
pwm target duty cycle needs to be written. Since we don't know the actual
pwm duty cycle after a target pwm duty cycle has been written, set the
valid flag to false to indicate that actual pwm duty cycle should be read
from the chip instead of using cached values.

Cc: Jan Kundrát 
Cc: Václav Kubernát 
Signed-off-by: Guenter Roeck 
Tested-by: Václav Kubernát 
Reviewed-by: Jan Kundrát 
Link: https://lore.kernel.org/r/20210526154022.3223012-3-linux@roeck-us.net
Signed-off-by: Sasha Levin