commit 7a18afe8097731b8ffb6cb5b2b3b418ded77c105 upstream.

On ads7828 the internal reference defaults to off upon power up. When
using internal reference, it needs to be turned on and the voltage needs
to settle before normal conversion cycle can be started. Hence perform a
dummy read in the probe to enable the internal reference allowing the
voltage to settle before performing a normal read.

Without this fix, the first read from the ADC when using internal
reference always returns incorrect data.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm:pxa_defconfig can result in the following crash if the max1111 driver
is not instantiated.

Unhandled fault: page domain fault (0x01b) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 1b [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 300 Comm: kworker/0:1 Not tainted 4.5.0-01301-g1701f680407c #10
Hardware name: SHARP Akita
Workqueue: events sharpsl_charge_toggle
task: c390a000 ti: c391e000 task.ti: c391e000
PC is at max1111_read_channel+0x20/0x30
LR is at sharpsl_pm_pxa_read_max1111+0x2c/0x3c
pc : [<c03aaab0>]    lr : [<c0024b50>]    psr: 20000013
...
[<c03aaab0>] (max1111_read_channel) from [<c0024b50>]
					(sharpsl_pm_pxa_read_max1111+0x2c/0x3c)
[<c0024b50>] (sharpsl_pm_pxa_read_max1111) from [<c00262e0>]
					(spitzpm_read_devdata+0x5c/0xc4)
[<c00262e0>] (spitzpm_read_devdata) from [<c0024094>]
					(sharpsl_check_battery_temp+0x78/0x110)
[<c0024094>] (sharpsl_check_battery_temp) from [<c0024f9c>]
					(sharpsl_charge_toggle+0x48/0x110)
[<c0024f9c>] (sharpsl_charge_toggle) from [<c004429c>]
					(process_one_work+0x14c/0x48c)
[<c004429c>] (process_one_work) from [<c0044618>] (worker_thread+0x3c/0x5d4)
[<c0044618>] (worker_thread) from [<c004a238>] (kthread+0xd0/0xec)
[<c004a238>] (kthread) from [<c000a670>] (ret_from_fork+0x14/0x24)

This can occur because the SPI controller driver (SPI_PXA2XX) is built as
module and thus not necessarily loaded. While building SPI_PXA2XX into the
kernel would make the problem disappear, it appears prudent to ensure that
the driver is instantiated before accessing its data structures.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull ARM SoC driver updates from Arnd Bergmann:
 "Driver updates for ARM SoCs, these contain various things that touch
  the drivers/ directory but got merged through arm-soc for practical
  reasons:

   - Rockchip rk3368 gains power domain support
   - Small updates for the ARM spmi driver
   - The Atmel PMC driver saw a larger rework, touching both
     arch/arm/mach-at91 and drivers/clk/at91
   - All reset controller driver changes alway get merged through
     arm-soc, though this time the largest change is the addition of a
     MIPS pistachio reset driver
   - One bugfix for the NXP (formerly Freescale) i.MX weim bus driver"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
  bus: imx-weim: Take the 'status' property value into account
  clk: at91: remove useless includes
  clk: at91: pmc: remove useless capacities handling
  clk: at91: pmc: drop at91_pmc_base
  usb: gadget: atmel: access the PMC using regmap
  ARM: at91: remove useless includes and function prototypes
  ARM: at91: pm: move idle functions to pm.c
  ARM: at91: pm: find and remap the pmc
  ARM: at91: pm: simply call at91_pm_init
  clk: at91: pmc: move pmc structures to C file
  clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
  clk: at91: remove IRQ handling and use polling
  clk: at91: make use of syscon/regmap internally
  clk: at91: make use of syscon to share PMC registers in several drivers
  hwmon: (scpi) add energy meter support
  firmware: arm_scpi: add support for 64-bit sensor values
  firmware: arm_scpi: decrease Tx timeout to 20ms
  firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
  reset: sti: Make reset_control_ops const
  reset: zynq: Make reset_control_ops const
  ...

Create a driver to support the hardware monitoring chip present in
the Zyxel NSA320 and some of the other Zyxel NAS devices.

The driver reads fan speed and temperature from a suitably
pre-programmed MCU on the device.

Signed-off-by: Adam Baker <linux@baker-net.org.uk>
[groeck: Dropped .owner field initialization]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

ADM1278 is mostly compatible to other chips of the same series.
Besides the usual difference in coefficients, it supports
a temperature sensor, and it can measure both input and output
voltage at the same time.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This patch adds support for the Murata NCP15XH103 thermistor series.

Signed-off-by: Joseph McNally <jmcna06@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Currently the driver calls hwmon_device_register_with_groups which
does not accept hypen in node name and returns EINVAL. Use of hypen
in device tree node name results in probe failure., however use of
hypen in device tree node name is perfectly acceptable.

Change this by allocating a duplicate managed string, replacing
hypen with underscore and then calling hwmon_device_register_with_groups.
This allows the use of hypen in device tree node name while maintaining
backwards compatibility and preventing any possible regressions with
user space.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This adds support for the Linear Technology LTC2990  I2C System Monitor.
The LTC2990 supports a combination of voltage, current and temperature
monitoring. This driver currently only supports reading two currents
by measuring two differential voltages across series resistors, in
addition to the Vcc supply voltage and internal temperature.

This is sufficient to support the Topic Miami SOM which uses this chip
to monitor the currents flowing into the FPGA and the CPU parts.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The vexpress hwmon implementation is currently just called vexpress.
This is a problem because it clashes with another module with the same
name in regulators.

This patch renames the vexpress hwmon implementation to vexpress-hwmon
so that there will be no clash in the module namespace.

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

SCPI updates and fixes for v4.6

1. Minor fix to restore functionality in big-endian mode

2. Fix race by decreasing Tx timeout to 20ms

3. Adds support for 64-bit sensor values and energy meter

* tag 'scpi-for-v4.6/updates' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  hwmon: (scpi) add energy meter support
  firmware: arm_scpi: add support for 64-bit sensor values
  firmware: arm_scpi: decrease Tx timeout to 20ms
  firmware: arm_scpi: fix send_message and sensor_get_value for big-endian

Signed-off-by: Olof Johansson <olof@lixom.net>