linux-stable.git/drivers/hwmon, branch v4.4.2

hwmon: (sht15) Select CONFIG_BITREVERSE

2015-12-18T16:19:52+00:00

If CONFIG_BITREVERSE is not built-in, the sht15 driver fails to link:

drivers/built-in.o: In function `sht15_crc8':
drivers/hwmon/sht15.c:195: undefined reference to `byte_rev_table'

This adds a Kconfig 'select' statement, like all other users of
bitrev.h have it.

Signed-off-by: Arnd Bergmann 
Fixes: 33836ee98533 ("hwmon:change sht15_reverse()")
Signed-off-by: Guenter Roeck

hwmon: (tmp102) Force wait for conversion time for the first valid data

2015-12-10T16:14:22+00:00

TMP102 works based on conversions done periodically. However, as per
the TMP102 data sheet[1] the first conversion is triggered immediately
after we program the configuration register. The temperature data
registers do not reflect proper data until the first conversion is
complete (in our case HZ/4).

The driver currently sets the last_update to be jiffies - HZ, just
after the configuration is complete. When TMP102 driver registers
with the thermal framework, it immediately tries to read the sensor
temperature data. This takes place even before the conversion on the
TMP102 is complete and results in an invalid temperature read.

Depending on the value read, this may cause thermal framework to
assume that a critical temperature event has occurred and attempts to
shutdown the system.

Instead of causing an invalid mid-conversion value to be read
erroneously, we mark the last_update to be in-line with the current
jiffies. This allows the tmp102_update_device function to skip update
until the required conversion time is complete. Further, we ensure to
return -EAGAIN result instead of returning spurious temperature (such
as 0C) values to the caller to prevent any wrong decisions made with
such values. NOTE: this allows the read functions not to be blocking
and allows the callers to make the decision if they would like to
block or try again later. At least the current user(thermal) seems to
handle this by retrying later.

A simpler alternative approach could be to sleep in the probe for the
duration required, but that will result in latency that is undesirable
and delay boot sequence un-necessarily.

[1] http://www.ti.com/lit/ds/symlink/tmp102.pdf

Cc: Eduardo Valentin 
Reported-by: Aparna Balasubramanian 
Reported-by: Elvita Lobo 
Reported-by: Yan Liu 
Signed-off-by: Nishanth Menon 
Signed-off-by: Guenter Roeck

hwmon: (scpi) skip unsupported sensors properly

2015-11-16T17:59:50+00:00

Currently it's assumed that firmware exports only the class of sensors
supported by the driver. However with newer firmware or SCPI protocol
revision, support for newer classes of sensors can be present.

The driver fails to probe with the following warning if an unsupported
class of sensor is encountered in the firmware.

sysfs: cannot create duplicate filename
	'/devices/platform/scpi/scpi:sensors/hwmon/hwmon0/'
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:31
Modules linked in:

CPU: 0 PID: 6 Comm: kworker/u12:0 Not tainted 4.3.0-rc7 #137
Hardware name: ARM Juno development board (r0) (DT)
Workqueue: deferwq deferred_probe_work_func
PC is at sysfs_warn_dup+0x54/0x78
LR is at sysfs_warn_dup+0x54/0x78

This patch fixes the above issue by skipping through the unsupported
class of SCPI sensors.

Fixes: 68acc77a2d51 ("hwmon: Support thermal zones registration for SCP temperature sensors")
Fixes: ea98b29a05e9 ("hwmon: Support sensors exported via ARM SCP interface")
Cc: Guenter Roeck 
Reviewed-by: Punit Agrawal 
Signed-off-by: Sudeep Holla 
Signed-off-by: Guenter Roeck

hwmon: (scpi) add thermal-of dependency

2015-11-16T17:54:45+00:00

The newly added scpi thermal support is broken when the scpi driver
is built-in but the thermal driver is a loadable module:

drivers/built-in.o: In function `scpi_hwmon_probe':
(.text+0x444d70): undefined reference to `thermal_zone_of_sensor_unregister'
(.text+0x444d94): undefined reference to `thermal_zone_of_sensor_register'
drivers/built-in.o: In function `scpi_hwmon_remove':
(text+0x444e6c): undefined reference to `thermal_zone_of_sensor_unregister'

This uses the same Kconfig trick that we have in a couple of other
drivers already to ensure we can only select the driver in valid
configurations when either THERMAL_OF is disabled, or when with a
dependency on CONFIG_THERMAL that can force SCPI to be a loadable
module in the case I was hitting.

Signed-off-by: Arnd Bergmann 
Fixes: 68acc77a2d51 ("hwmon: Support thermal zones registration for SCP temperature sensors")
Signed-off-by: Guenter Roeck

hwmon : (applesmc) Fix uninitialized variables warnings

2015-11-16T05:52:39+00:00

Fix the following "maybe used uninitialized" warnings by
initializing the variables to keep the compiler quiet.
There is no "used uninitialized" in this case.

  CC [M]  drivers/hwmon/applesmc.o
drivers/hwmon/applesmc.c: In function ‘applesmc_init_smcreg’:
drivers/hwmon/applesmc.c:595:43: warning: ‘right_light_sensor’
may be used uninitialized in this function [-Wmaybe-uninitialized]
  s->num_light_sensors = left_light_sensor + right_light_sensor;
                                           ^
drivers/hwmon/applesmc.c:540:26: note: ‘right_light_sensor’ was
declared here
  bool left_light_sensor, right_light_sensor;
                          ^
drivers/hwmon/applesmc.c:595:43: warning: ‘left_light_sensor’ may
be used uninitialized in this function [-Wmaybe-uninitialized]
  s->num_light_sensors = left_light_sensor + right_light_sensor;
                                           ^
drivers/hwmon/applesmc.c:540:7: note: ‘left_light_sensor’ was
declared here
  bool left_light_sensor, right_light_sensor;
       ^

Signed-off-by: Shuah Khan 
Signed-off-by: Guenter Roeck

hwmon: (ina2xx) Fix build issue by selecting REGMAP_I2C

2015-11-16T05:52:39+00:00

Since a0de56c81fcf ("hwmon: (ina2xx) convert driver to using regmap")
the driver requires REGMAP_I2C to build.  Select it by default
in Kconfig.

Reported-by: Guo Chunrong 
Cc: Marc Titinger 
Signed-off-by: Li Yang 
Fixes: a0de56c81fcf ("hwmon: (ina2xx) convert driver to using regmap")
Signed-off-by: Guenter Roeck

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2015-11-10T23:00:03+00:00

Pull ARM SoC driver updates from Olof Johansson:
 "As we've enabled multiplatform kernels on ARM, and greatly done away
  with the contents under arch/arm/mach-*, there's still need for
  SoC-related drivers to go somewhere.

  Many of them go in through other driver trees, but we still have
  drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
  that might be shared between ARM and ARM64 (or just in general makes
  sense to not have under the architecture directory).

  This branch contains mostly such code:

   - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
     communicate with power management blocks on these SoCs for use by
     clock, regulator and bus frequency drivers.

   - Allwinner Reduced Serial Bus driver, again used to communicate with
     PMICs.

   - Drivers for ARM's SCPI (System Control Processor).  Not to be
     confused with PSCI (Power State Coordination Interface).  SCPI is
     used to communicate with the assistant embedded cores doing power
     management, and we have yet to see how many of them will implement
     this for their hardware vs abstracting in other ways (or not at all
     like in the past).

   - To make confusion between SCPI and PSCI more likely, this release
     also includes an update of PSCI to interface version 1.0.

   - Rockchip support for power domains.

   - A driver to talk to the firmware on Raspberry Pi"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
  soc: qcom: smd-rpm: Correct size of outgoing message
  bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
  bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
  ARM: bcm2835: add mutual inclusion protection
  drivers: psci: make PSCI 1.0 functions initialization version dependent
  dt-bindings: Correct paths in Rockchip power domains binding document
  soc: rockchip: power-domain: don't try to print the clock name in error case
  soc: qcom/smem: add HWSPINLOCK dependency
  clk: berlin: add cpuclk
  ARM: berlin: dts: add CLKID_CPU for BG2Q
  ARM: bcm2835: Add the Raspberry Pi firmware driver
  soc: qcom: smem: Move RPM message ram out of smem DT node
  soc: qcom: smd-rpm: Correct the active vs sleep state flagging
  soc: qcom: smd: delete unneeded of_node_put
  firmware: qcom-scm: build for correct architecture level
  soc: qcom: smd: Correct SMEM items for upper channels
  qcom-scm: add missing prototype for qcom_scm_is_available()
  qcom-scm: fix endianess issue in __qcom_scm_is_call_available
  soc: qcom: smd: Reject send of too big packets
  soc: qcom: smd: Handle big endian CPUs
  ...

Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging

2015-11-10T18:09:01+00:00

Pull tiny hwmon update from Jean Delvare.

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (k10temp) Remove duplicate pci-id define

hwmon: (k10temp) Remove duplicate pci-id define

2015-11-09T09:14:29+00:00

PCI_DEVICE_ID_AMD_15H_M60H_NB_F3 is now defined in pci_ids.h

Signed-off-by: Adam Majer 
Acked-by: Clemens Ladisch 
Signed-off-by: Jean Delvare

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial

2015-11-07T21:05:44+00:00

Pull trivial updates from Jiri Kosina:
 "Trivial stuff from trivial tree that can be trivially summed up as:

   - treewide drop of spurious unlikely() before IS_ERR() from Viresh
     Kumar

   - cosmetic fixes (that don't really affect basic functionality of the
     driver) for pktcdvd and bcache, from Julia Lawall and Petr Mladek

   - various comment / printk fixes and updates all over the place"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
  bcache: Really show state of work pending bit
  hwmon: applesmc: fix comment typos
  Kconfig: remove comment about scsi_wait_scan module
  class_find_device: fix reference to argument "match"
  debugfs: document that debugfs_remove*() accepts NULL and error values
  net: Drop unlikely before IS_ERR(_OR_NULL)
  mm: Drop unlikely before IS_ERR(_OR_NULL)
  fs: Drop unlikely before IS_ERR(_OR_NULL)
  drivers: net: Drop unlikely before IS_ERR(_OR_NULL)
  drivers: misc: Drop unlikely before IS_ERR(_OR_NULL)
  UBI: Update comments to reflect UBI_METAONLY flag
  pktcdvd: drop null test before destroy functions