linux-stable.git/drivers/hwmon, branch v2.6.38

hwmon/f71882fg: Set platform drvdata to NULL later

2011-03-13T14:42:52+00:00

This avoids a possible race leading to trying to dereference NULL.

Signed-off-by: Hans de Goede 
Acked-by: Jean Delvare 
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck

hwmon/f71882fg: Fix a typo in a comment

2011-03-13T14:40:41+00:00

Signed-off-by: Hans de Goede 
Acked-by: Jean Delvare 
Signed-off-by: Guenter Roeck

hwmon: (adt7411) add MODULE_DEVICE_TABLE

2011-02-26T16:59:32+00:00

The device table is required to load modules based on modaliases.

Signed-off-by: Axel Lin 
Acked-by: Wolfram Sang 
Signed-off-by: Guenter Roeck

hwmon: (ad7414) add MODULE_DEVICE_TABLE

2011-02-26T16:59:32+00:00

The device table is required to load modules based on modaliases.

Signed-off-by: Axel Lin 
Signed-off-by: Guenter Roeck

hwmon: (lm85) extend to support EMC6D103 chips

2011-02-19T01:43:36+00:00

The interface is identical EMC6D102, so all that needs to be added are
some definitions and their uses.

Registers apparently missing in EMC6D103S/EMC6D103:A2 compared to EMC6D103:A0,
EMC6D103:A1, and EMC6D102 (according to the data sheets), but used
unconditionally in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. For that
reason, EMC6D103S chips don't get enabled for the time being.

Signed-off-by: Jan Beulich 
(Guenter Roeck: Replaced EMC6D103_A2 with EMC6D103S per EMC6D103S datasheet)
Signed-off-by: Guenter Roeck 
Cc: stable@kernel.org

hwmon: (k10temp) add support for AMD Family 12h/14h CPUs

2011-02-18T14:14:24+00:00

Add the PCI ID to support the internal temperature sensor of the
AMD "Llano" and "Brazos" processor families.

Signed-off-by: Clemens Ladisch 
Cc: stable@kernel.org # ca86828: x86, AMD, PCI: Add AMD northbridge PCI device
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck

hwmon: (jc42) do not allow writing to locked registers

2011-02-16T16:18:33+00:00

On systems where the temperature sensor is actually used, the BIOS is
likely to have locked the alarm registers.  In that case, all writes
through the corresponding sysfs files would be silently ignored.

To prevent this, detect the locks and make the affected sysfs files
read-only.

Signed-off-by: Clemens Ladisch 
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck

hwmon: (jc42) more helpful documentation

2011-02-16T16:18:32+00:00

The documentation lists standard numbers and chip names in excruciating
detail, but that's all it does.  To help mere mortals in deciding
whether to enable this driver, mention what this sensor is for and in
which systems it might be found.

Also add a link to the actual JC 42.4 specification.

Signed-off-by: Clemens Ladisch 
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck

hwmon: (jc42) fix type mismatch

2011-02-16T16:18:31+00:00

In set_temp_crit_hyst(), make the variable 'val' have the correct
type for strict_strtoul().

Signed-off-by: Clemens Ladisch 
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck

hwmon: (emc1403) Fix I2C address range

2011-02-09T21:45:52+00:00

I2C address range included 0x2a, which the chips do not support.
Replace with 0x29 which is supported but was missing.

Signed-off-by: Guenter Roeck 
Acked-by: Jean Delvare