The MIPI DSI output on Tegra SoCs requires some external logic to
calibrate the MIPI pads before a video signal can be transmitted. This
MIPI calibration logic requires to be powered on while the MIPI pads are
being used, which is currently done as part of the DSI driver's probe
implementation.

This is suboptimal because it will leave the MIPI calibration logic
powered up even if the DSI output is never used.

On Tegra114 and earlier this behaviour also causes the driver to hang
while trying to power up the MIPI calibration logic because the power
partition that contains the MIPI calibration logic will be powered on
by the display controller at output pipeline configuration time. Thus
the power up sequence for the MIPI calibration logic happens before
it's power partition is guaranteed to be enabled.

Fix this by splitting up the API into a request/free pair of functions
that manage the runtime dependency between the DSI and the calibration
modules (no registers are accessed) and a set of enable, calibrate and
disable functions that program the MIPI calibration logic at points in
time where the power partition is really enabled.

While at it, make sure that the runtime power management also works in
ganged mode, which is currently also broken.

Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Tested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Backmerge drm-next to be able to apply Chris' connector_unregister_all
cleanup (need latest i915 and sun4i state for that).

Also there's a trivial conflict in ttm_bo.c that git rerere fails to
remember.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

The vunmap() function performs also input parameter validation.
Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/b3fbdcaf-1bda-7ce9-935b-2d716727ec39@users.sourceforge.net

drm/tegra: Changes for v4.8-rc1

This set of changes contains a bunch of cleanups to the host1x driver as
well as the addition of a pin controller for DPAUX, which is required by
boards to configure the DPAUX pads in AUX mode (for DisplayPort) or I2C
mode (for HDMI and DDC).

Included is also a bit of rework of the SOR driver in preparation to add
DisplayPort support as well as some refactoring and cleanup.

Finally, all output drivers are converted to runtime PM, which greatly
simplifies the handling of clocks and resets.

* tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux: (35 commits)
  drm/tegra: sor: Reject HDMI 2.0 modes
  drm/tegra: sor: Prepare for generic PM domain support
  drm/tegra: dsi: Prepare for generic PM domain support
  drm/tegra: sor: Make XBAR configurable per SoC
  drm/tegra: sor: Use sor1_src clock to set parent for HDMI
  dt-bindings: display: tegra: Add source clock for SOR
  drm/tegra: sor: Implement sor1_brick clock
  drm/tegra: sor: Implement runtime PM
  drm/tegra: hdmi: Implement runtime PM
  drm/tegra: dsi: Implement runtime PM
  drm/tegra: dc: Implement runtime PM
  drm/tegra: hdmi: Enable audio over HDMI
  drm/tegra: sor: Do not support deep color modes
  drm/tegra: sor: Extract tegra_sor_mode_set()
  drm/tegra: sor: Split out tegra_sor_apply_config()
  drm/tegra: sor: Rename tegra_sor_calc_config()
  drm/tegra: sor: Factor out tegra_sor_set_parent_clock()
  drm/tegra: dpaux: Add pinctrl support
  dt-bindings: Add bindings for Tegra DPAUX pinctrl driver
  drm/tegra: Prepare DPAUX for supporting generic PM domains
  ...

Enabling HDMI 2.0 modes requires extra programming and will not work
with the current driver, so reject all those modes.

Signed-off-by: Thierry Reding <treding@nvidia.com>

The SOR driver for Tegra requires the SOR power partition to be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework. However, the sequence for
gating/ungating the SOR power partition requires that the SOR reset is
asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the SOR
driver cannot request the same reset unless we mark the reset as shared.
Sharing resets will not work in this case because we cannot guarantee
that the reset will be asserted/de-asserted at the appropriate time.
Therefore, given that the Tegra generic PM domain code will handle the
resets, do not request the reset in the SOR driver if the SOR device has
a PM domain associated.

Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The DSI driver for Tegra requires the SOR power partition to be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework. However, the sequence for
gating/ungating the SOR power partition requires that the DSI reset is
asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the DSI
driver cannot request the same reset unless we mark the reset as shared.
Sharing resets will not work in this case because we cannot guarantee
that the reset will be asserted/de-asserted at the appropriate time.
Therefore, given that the Tegra generic PM domain code will handle the
resets, do not request the reset in the DSI driver if the DSI device has
a PM domain associated.

Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Provide a per-SoC mapping of lanes which can be used to configure the
XBAR.

Signed-off-by: Thierry Reding <treding@nvidia.com>

When running in HDMI mode, the sor1 IP block needs to use the sor1_src
as parent clock, and in turn configure the sor1_src to use pll_d2_out0
as its parent.

Signed-off-by: Thierry Reding <treding@nvidia.com>

sor1_brick is a clock that can be used as a source for the sor1 clock.
The registers to control the clock output are part of the sor1 IP block
and hence the sor driver is the best place to implement it.

Signed-off-by: Thierry Reding <treding@nvidia.com>