Here are some development updates for the Synopsis Designware HDMI driver,
which clean up some of the code, and start preparing to add audio support
to the driver.  This series of patches are based on a couple of dependent
commits from the ALSA tree.

Briefly, the updates are:
- move comments which should have moved with the phy values to the IMX
  part of the driver.
- clean up the phy configuration: to all lookups before starting to
  program the phy.
- clean up the HDMI clock regenerator code
- use the drm_hdmi_avi_infoframe_from_display_mode() helper which allows
  the code to be subsequently simplified
- remove the unused 'regmap' pointer in struct dw_hdmi
- use the bridge drm device rather than the connector (we're the bridge
  code)
- remove private hsync/vsync/interlaced flags, getting them from the
  DRM mode structure instead.
- implement interface functions to support audio - setting the audio
  sample rate, and enabling the audio clocks.
- removal of broken pixel repetition support
- cleanup DVI vs HDMI sink handling
- enable audio only if connected device supports audio
- avoid double-enabling bridge in the sink path (once in mode_set, and
  again in commit)
- rename mis-named dw_hdmi_phy_enable_power()
- fix bridge enable/disable handing, so a plug-in event doesn't
  reconfigure the bridge if DRM has disabled the output
- fix from Vladimir Zapolskiy for the I2CM_ADDRESS macro name

These are primerily preparitory patches for the AHB audio driver and
the I2S audio driver (from Rockchip) for this IP.

* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  drm: bridge/dw_hdmi: fix register I2CM_ADDRESS register name
  drm: bridge/dw_hdmi: fix phy enable/disable handling
  drm: bridge/dw_hdmi: rename dw_hdmi_phy_enable_power()
  drm: bridge/dw_hdmi: avoid enabling interface in mode_set
  drm: bridge/dw_hdmi: enable audio only if sink supports audio
  drm: bridge/dw_hdmi: clean up HDMI vs DVI mode handling
  drm: bridge/dw_hdmi: don't support any pixel doubled modes
  drm: bridge/dw_hdmi: remove pixel repetition setting for all VICs
  drm: bridge/dw_hdmi: introduce interfaces to enable and disable audio
  drm: bridge/dw_hdmi: introduce interface to setting sample rate
  drm: bridge/dw_hdmi: remove mhsyncpolarity/mvsyncpolarity/minterlaced
  drm: bridge/dw_hdmi: use our own drm_device
  drm: bridge/dw_hdmi: remove unused 'regmap' struct member
  drm: bridge/dw_hdmi: simplify hdmi_config_AVI() a little
  drm: bridge/dw_hdmi: use drm_hdmi_avi_infoframe_from_display_mode()
  drm: bridge/dw_hdmi: clean up hdmi_set_clk_regenerator()
  drm: bridge/dw_hdmi: clean up phy configuration
  drm: imx/dw_hdmi: move phy comments
  drm/edid: add function to help find SADs

The phy comments in dw_hdmi.c applied to the iMX6 version.  Move these
comments to the iMX6 dw_hdmi-imx data along side the data.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit a7c6e76feeb1 ("drm/imx: switch to use media bus formats") accidentally
replaced IPU_PIX_FMT_GBR24 with MEDIA_BUS_FMT_YUV8_1X24 instead of the correct
MEDIA_BUS_FMT_GBR888_1X24. This patch is needed to fix VGA output in i.MX53.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

The parallel-display driver used an undocumented, non-standard property
"fsl,panel" to optionally associate with a drm_panel device. This patch
fixes the driver to use the same OF graph bindings as the LDB driver
instead:

    parallel-display {
            compatible = "fsl,imx-parallel-display";
            ...

            port@1 {
                    reg = <1>;

                    parallel_out: endpoint {
                            remote_endpoint = <&panel_in>;
                    };
            };
    };

    panel {
            ...

            port {
                    panel_in: endpoint {
                            remote-endpoint = <&parallel_out>;
                    };
            };
    };

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>

This set of patches adjust the setup of the HDMI CTS/N values for audio
support to be compliant with the work-around given in the iMX6 errata
documentation as part of the preparation for integrating audio support
for this driver, and also update the HDMI phy configuration for Rockchip
devices to improve the HDMI eye pattern.

* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  drm: rockchip/dw_hdmi-rockchip: improve for HDMI electrical test
  drm: bridge/dw_hdmi: separate VLEVCTRL settting into platform driver
  drm: bridge/dw_hdmi: fixed codec style
  drm: bridge/dw_hdmi: adjust n/cts setting order
  drm: bridge/dw_hdmi: protect n/cts setting with a mutex
  drm: bridge/dw_hdmi: combine hdmi_set_clock_regenerator_n() and hdmi_regenerate_cts()

Conflicts:
	drivers/gpu/drm/imx/dw_hdmi-imx.c

imx-drm changes to use media bus formats and LDB drm_panel support

- Add media bus formats needed by imx-drm
- Switch to use media bus formats to describe the pixel format
  on the internal parallel bus between display interface and
  encoders
- Some preparations for TV Output via TVEv2 on i.MX5
- Add drm_panel support to the i.MX LVDS driver, allow to
  determine the bus pixel format from the panel descriptor.

* tag 'imx-drm-next-2015-03-31' of git://git.pengutronix.de/git/pza/linux:
  drm/imx: imx-ldb: allow to determine bus format from the connected panel
  drm/imx: imx-ldb: reset display clock input when disabling LVDS
  drm/imx: imx-ldb: add drm_panel support
  drm/imx: consolidate bus format variable names
  drm/imx: switch to use media bus formats
  Add RGB666_1X24_CPADHI media bus format
  Add YUV8_1X24 media bus format
  Add BGR888_1X24 and GBR888_1X24 media bus formats
  Add LVDS RGB media bus formats
  Add RGB444_1X12 and RGB565_1X16 media bus formats
  drm/imx: ipuv3-crtc: Allow to divide DI clock from TVEv2
  drm/imx: Add support for interlaced scanout

Using the for_each_... macro should make the code bit shorter and
easier to read. This patch also properly decrements the endpoint node
reference count before returning out of the loop.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

Because of iMX6 & Rockchip have differnet mpll config parameter,
the VLEVCTRL parameter would be different. In this case we should
separate VLEVCTRL setting from the common dw_hdmi driver, config
this parameter in platform driver(dw_hdmi-imx and dw_hdmi-rockchip)

Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch makes the fsl,data-width and fsl,data-mapping device tree
properties optional if a panel is connected to the ldb output port
via the of_graph bindings. The data mapping is determined from the
display_info.bus_format field provided by the panel.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

The LDB driver changes the attached display interface's input clock mux
to the LDB_DI clock reference. Change it back again when disabling the
LVDS display. Changing back to the PLL5 for example allows to configure
the same DI for HDMI output later.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>