commit a5241289c4139f0521b89e34a70f5f998463ae15 upstream.

The EDID read code waits for the read completion interrupt to occur
using wait_event_interruptible(). The condition passed to the macro
reads I2C registers. This results in sleeping with the task state set
to TASK_INTERRUPTIBLE, triggering a WARN_ON() introduced in commit
8eb23b9f35aae ("sched: Debug nested sleeps").

Fix this by reworking the EDID read code. Instead of checking whether
the read is complete through I2C reads, handle the interrupt registers
in the interrupt handler and update a new edid_read flag accordingly. As
a side effect both the IRQ and polling code paths now process the
interrupt sources through the same code path, simplifying the code.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2e96206c4f952295e11c311fbb2a7aa2105024af upstream.

The DDC error interrupt bit is located in REG_INT1, not REG_INT0. Update
both the interrupt wait code and the interrupt sources reset code
accordingly.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

3 fixes for the tda998x.

* 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  drm/i2c: tda998x: set the CEC I2C address based on the slave I2C address
  drm: tda998x: Fix EDID read timeout on HDMI connect
  drm: tda998x: Protect the page register

The I2C address for the TDA9989 and TDA19989 is fixed at 0x34 but the
two LSBs of the TDA19988's address are set by two configuration pins
on the chip.  Irrespective of the chip, the associated CEC peripheral's
I2C address is based upon the main I2C address.

This patch avoids any special handling required to support systems that
contain multiple TDA19988 devices on the same I2C bus.

Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When the HDMI cable is disconnected and reconnected, EDID reading
is called too early raising a EDID read timeout.
This patch uses the system work queue to delay the notification
of the HDMI connect/disconnect event.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As the HDMI registers of the TDA998x chips are accessed by pages,
the page register must be protected.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch adds a driver for the Analog Devices adv7511. The adv7511 is
a standalone HDMI transmitter chip. It features a HDMI output interface
on one end and video and audio input interfaces on the other.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Signed-off-by: Dave Airlie <airlied@redhat.com>

This builds upon the previous set of fixes which were pulled on 6th July.
Included in this set are:
- an update from Jean-Francois to add the missing reg documentation entry
  to the device tree documentation.
- conversion of the tda998x driver to the component helpers.

* 'tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
  drm/i2c: tda998x: add component support
  drm/i2c: tda998x: allow re-use of tda998x support code
  drm/i2c: tda998x: fix lack of required reg in DT documentation

Conflicts:
	drivers/gpu/drm/i2c/tda998x_drv.c

Add component helper support to the tda998x driver.  This permits the
TDA998x to be declared as a separate device in device tree, and bound
at the appropriate moment with a co-operating card driver.

The existing slave_encoder interfaces are kept while there are existing
users of it in order to prevent regressions.

Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>