This patch is to fill in the data member of v2 gpu metrics
table for vangogh.

Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On some boards the rpm interface apparently does not work at all
leading to the fan not spinning or spinning at strange speeds.
Revert this for now to fix 5.10, 5.11.  The follow on patch
fixes this properly for 5.12.

This reverts commit 8d6e65adc25e23fabbc5293b6cd320195c708dca.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1408
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

In the renoir there is no need GpuChangeState message set to exit gfxoff in the s0i3 resume since
mmnbif_gpu_BIF_DOORBELL_FENCE_CNTL has been added in the s0i3 FSDL.

Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

This patch is to improve the fine grain tuning function for RV/RV2/PCO.
The fine grain tuning function uses the sysfs node -- pp_od_clk_voltage
to config gfxclk. Meanwhile, another sysfs
node -- power_dpm_force_perfomance_level also affects the gfx clk.
It will cause confusion when these two sysfs nodes works
together. So this patch adds one flag to avoid this confusion, the flag
will make these two sysfs nodes work separately.
The flag is set as "disabled" by default, so the fine grain tuning function
will be disabled by default.
Only when power_dpm_force_perfomance_level is changed to
"manual" mode, the flag will be set as "enabled",
and the fine grain tuning function will be enabled.
In other profile modes, including "auto", "high", "low",
"profile_peak", "profile_standard", "profile_min_sclk",
"profile_min_mclk", the flag will be set as "disabled",
and the od range of fine grain tuning function will
be restored default value.

Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch is to fix the failure when change power profile to
"profile_peak" for renoir.

Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

sienna cichlid interfaces with RAS eeprom on I2C controller port 1

Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.

Command guide:
echo "s level value" > pp_od_clk_voltage
        "s" - set the sclk frequency
        "level" - 0 or 1, "0" represents the min value,  "1" represents
        the max value
        "value" - the target value of sclk frequency, it should be limited in the
        safe range
echo "r" > pp_od_clk_voltage
        "r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
        "c" - commit the min and max value of sclk frequency to the system
        only after the commit command, the target values set by "s" command
        will take effect.
Example:
1)change power profile from "auto" to "manual"
        $ cat power_dpm_force_performance_level
        auto
        $ echo "manual" > power_dpm_force_performance_level
        $ cat power_dpm_force_performance_level
        manual
2)check the default sclk frequency
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        200Mhz
        1:       1400Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
        $ echo "s 0 600" > pp_od_clk_voltage
        $ echo "s 1 1000" > pp_od_clk_voltage
        $ echo "c" > pp_od_clk_voltage
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        600Mhz
        1:       1000Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
        $ echo "r" > pp_od_clk_voltage
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        200Mhz
        1:       1400Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz

Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch is to correct the sensor value of power for vangogh.

Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This can suppress the annoying but unharmful prompts.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Only pmfw version behind v4.63.23.00 could support this message.

Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>