Pull drm updates from Dave Airlie:
 "This is the main pull request for the drm subsystems for 6.10.

  In drivers the main thing is a new driver for ARM Mali firmware based
  GPUs, otherwise there are a lot of changes to amdgpu/xe/i915/msm and
  scattered changes to everything else.

  In the core a bunch of headers and Kconfig was refactored, along with
  the addition of a new panic handler which is meant to provide a user
  friendly message when a panic happens and graphical display is
  enabled.

  New drivers:
   - panthor: ARM Mali/Immortalis CSF-based GPU driver

  Core:
   - add a CONFIG_DRM_WERROR option
   - make more headers self-contained
   - grab resv lock in pin/unpin
   - fix vmap resv locking
   - EDID/eDP panel matching
   - Kconfig cleanups
   - DT sound bindings
   - Add SIZE_HINTS property for cursor planes
   - Add struct drm_edid_product_id and helpers.
   - Use drm device based logging in more drm functions.
   - drop seq_file.h from a bunch of places
   - use drm_edid driver conversions

  dp:
   - DP Tunnel documentation
   - MST read sideband cap
   - Adaptive sync SDP prep work

  ttm:
   - improve placement for TTM BOs in idle/busy handling

  panic:
   - Fixes for drm-panic, and option to test it.
   - Add drm panic to simpledrm, mgag200, imx, ast

  bridge:
   - improve init ordering
   - adv7511: allow GPIO pin sharing
   - tc358775: add tc358675 support

  panel:
   - AUO B120XAN01.0
   - Samsung s6e3fa7
   - BOE NT116WHM-N44
   - CMN N116BCA-EA1,
   - CrystalClear CMT430B19N00
   - Startek KD050HDFIA020-C020A
   - powertip PH128800T006-ZHC01
   - Innolux G121X1-L03
   - LG sw43408
   - Khadas TS050 V2
   - EDO RM69380 OLED
   - CSOT MNB601LS1-1

  amdgpu:
   - HDCP/ODM/RAS fixes
   - Devcoredump improvements
   - Expose VCN activity via sysfs
   - SMY 13.0.x updates
   - Enable fast updates on DCN 3.1.4
   - Add dclk and vclk reporting on additional devices
   - Add ACA RAS infrastructure
   - Implement TLB flush fence
   - EEPROM handling fixes
   - SMUIO 14.0.2 support
   - SMU 14.0.1 Updates
   - SMU 14.0.2 support
   - Sync page table freeing with TLB flushes
   - DML2 refactor
   - DC debug improvements
   - DCN 3.5.x Updates
   - GPU reset fixes
   - HDP fix for second GFX pipe on GC 10.x
   - Enable secondary GFX pipe on GC 10.3
   - Refactor and clean up BACO/BOCO/BAMACO handling
   - Remove invalid TTM resource start check
   - UAF fix in VA IOCTL
   - GPUVM page fault redirection to secondary IH rings for IH 6.x
   - Initial support for mapping kernel queues via MES
   - Fix VRAM memory accounting

  amdkfd:
   - MQD handling cleanup
   - Preemption handling fixes for XCDs
   - TLB flush fix for GC 9.4.2
   - Properly clean up workqueue during module unload
   - Fix memory leak process create failure
   - Range check CP bad op exception targets to avoid reporting invalid exceptions to userspace
   - Fix eviction fence handling
   - Fix leak in GPU memory allocation failure case
   - DMABuf import handling fix
   - Enable SQ watchpoint for gfx10

  i915:
   - Adding new DG2 PCI ID
   - add context hints for GT frequency
   - enable only one CCS for compute workloads
   - new workarounds
   - Fix UAF on destroy against retire race and remove two earlier partial fixes
   - Limit the reserved VM space to only the platforms that need it
   - Fix gt reset with GuC submission is disable
   - Add and use gt_to_guc() wrapper

  i915/xe display:
   - Lunar Lake display enabling, including cdclk and other refactors
   - BIOS/VBT/opregion related refactor
   - Digital port related refactor/clean-up
   - Fix 2s boot time regression on DP panel replay init
   - Remove duplication on audio enable/disable on SDVO and g4x+ DP
   - Disable AuxCCS framebuffers if built for Xe
   - Make crtc disable more atomic
   - Increase DP idle pattern wait timeout to 2ms
   - Start using container_of_const() for some extra const safety
   - Fix Jasper Lake boot freeze
   - Enable MST mode for 128b/132b single-stream sideband
   - Enable Adaptive Sync SDP Support for DP
   - Fix MTL supported DP rates - removal of UHBR13.5
   - PLL refactoring
   - Limit eDP MSO pipe only for display version 20
   - More display refactor towards independence from i915 dev_priv
   - Convert i915/xe fbdev to DRM client
   - More initial work to make display code more independent from i915

  xe:
   - improved error capture
   - clean up some uAPI leftovers
   - devcoredump update
   - Add BMG mocs table
   - Handle GSCCS ER interrupt
   - Implement xe2- and GuC workarounds
   - struct xe_device cleanup
   - Hwmon updates
   - Add LRC parsing for more GPU instruction
   - Increase VM_BIND number of per-ioctl Ops
   - drm/xe: Add XE_BO_GGTT_INVALIDATE flag
   - Initial development for SR-IOV support
   - Add new PCI IDs to DG2 platform
   - Move userptr over to start using hmm_range_fault

  msm:
   - Switched to generating register header files during build process
     instead of shipping pre-generated headers
   - Merged DPU and MDP4 format databases.
   - DP:
     - Stop using compat string to distinguish DP and eDP cases
     - Added support for X Elite platform (X1E80100)
     - Reworked DP aux/audio support
     - Added SM6350 DP to the bindings
   - GPU:
     - a7xx perfcntr reg fixes
     - MAINTAINERS updates
     - a750 devcoredump support

  radeon:
   - Silence UBSAN warnings related to flexible arrays

  nouveau:
   - move some uAPI objects to uapi headers

  omapdrm:
   - console fix

  ast:
   - add i2c polling

  qaic:
   - add debugfs entries

  exynos:
   - fix platform_driver .owner
   - drop cleanup code

  mediatek:
   - Use devm_platform_get_and_ioremap_resource() in mtk_hdmi_ddc_probe()
   - Add GAMMA 12-bit LUT support for MT8188
   - Rename mtk_drm_* to mtk_*
   - Drop driver owner initialization
   - Correct calculation formula of PHY Timing"

* tag 'drm-next-2024-05-15' of https://gitlab.freedesktop.org/drm/kernel: (1477 commits)
  drm/xe/ads: Use flexible-array
  drm/xe: Use ordered WQ for G2H handler
  drm/msm/gen_header: allow skipping the validation
  drm/msm/a6xx: Cleanup indexed regs const'ness
  drm/msm: Add devcoredump support for a750
  drm/msm: Adjust a7xx GBIF debugbus dumping
  drm/msm: Update a6xx registers XML
  drm/msm: Fix imported a750 snapshot header for upstream
  drm/msm: Import a750 snapshot registers from kgsl
  MAINTAINERS: Add Konrad Dybcio as a reviewer for the Adreno driver
  MAINTAINERS: Add a separate entry for Qualcomm Adreno GPU drivers
  drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails
  drm/msm/adreno: fix CP cycles stat retrieval on a7xx
  drm/msm/a7xx: allow writing to CP_BV counter selection registers
  drm: zynqmp_dpsub: Always register bridge
  Revert "drm/bridge: ti-sn65dsi83: Fix enable error path"
  drm/fb_dma: Add checks in drm_fb_dma_get_scanout_buffer()
  drm/fbdev-generic: Do not set physical framebuffer address
  drm/panthor: Fix the FW reset logic
  drm/panthor: Make sure we handle 'unknown group state' case properly
  ...

It incorrectly claimed a resource isn't CPU visible if it's located at
the very end of CPU visible VRAM.

Fixes: a6ff969fe9cb ("drm/amdgpu: fix visible VRAM handling during faults")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3343
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reported-and-Tested-by: Jeremy Day <jsday@noreason.ca>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org

This patch adds a missed handling of PL domain doorbell while
handling VRAM faults.

Cc: Christian Koenig <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Fixes: a6ff969fe9cb ("drm/amdgpu: fix visible VRAM handling during faults")
Reviewed-by: Christian Koenig <christian.koenig@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Arvind Yadav <arvind.yadav@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This reverts drm/amdgpu: fix ftrace event amdgpu_bo_move always move
on same heap. The basic problem here is that after the move the old
location is simply not available any more.

Some fixes were suggested, but essentially we should call the move
notification before actually moving things because only this way we have
the correct order for DMA-buf and VM move notifications as well.

Also rework the statistic handling so that we don't update the eviction
counter before the move.

v2: add missing NULL check

Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 94aeb4117343 ("drm/amdgpu: fix ftrace event amdgpu_bo_move always move on same heap")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3171
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org

amd-drm-next-6.10-2024-04-26:

amdgpu:
- Misc code cleanups and refactors
- Support setting reset method at runtime
- Report OD status
- SMU 14.0.1 fixes
- SDMA 4.4.2 fixes
- VPE fixes
- MES fixes
- Update BO eviction priorities
- UMSCH fixes
- Reset fixes
- Freesync fixes
- GFXIP 9.4.3 fixes
- SDMA 5.2 fixes
- MES UAF fix
- RAS updates
- Devcoredump updates for dumping IP state
- DSC fixes
- JPEG fix
- Fix VRAM memory accounting
- VCN 5.0 fixes
- MES fixes
- UMC 12.0 updates
- Modify contiguous flags handling
- Initial support for mapping kernel queues via MES

amdkfd:
- Fix rescheduling of restore worker
- VRAM accounting for SVM migrations
- mGPU fix
- Enable SQ watchpoint for gfx10

Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240426221245.1613332-1-alexander.deucher@amd.com

Replace tmz flag into buffer flag to make it easier to understand
and extend

Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Frank Min <Frank.Min@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Maíra needs a backmerge to apply v3d patches, and Danilo for some
nouveau patches.

Signed-off-by: Maxime Ripard <mripard@kernel.org>

Add clear page support in vram memory region.

v1(Christian):
  - Dont handle clear page as TTM flag since when moving the BO back
    in from GTT again we don't need that.
  - Make a specialized version of amdgpu_fill_buffer() which only
    clears the VRAM areas which are not already cleared
  - Drop the TTM_PL_FLAG_WIPE_ON_RELEASE check in
    amdgpu_object.c

v2:
  - Modify the function name amdgpu_ttm_* (Alex)
  - Drop the delayed parameter (Christian)
  - handle amdgpu_res_cleared(&cursor) just above the size
    calculation (Christian)
  - Use AMDGPU_GEM_CREATE_VRAM_WIPE_ON_RELEASE for clearing the buffers
    in the free path to properly wait for fences etc.. (Christian)

v3(Christian):
  - Remove buffer clear code in VRAM manager instead change the
    AMDGPU_GEM_CREATE_VRAM_WIPE_ON_RELEASE handling to set
    the DRM_BUDDY_CLEARED flag.
  - Remove ! from amdgpu_res_cleared(&cursor) check.

v4(Christian):
  - vres flag setting move to vram manager file
  - use dma_fence_get_stub in amdgpu_ttm_clear_buffer function
  - make fence a mandatory parameter and drop the if and the get/put dance

Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <felix.kuehling@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240419063538.11957-2-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

When we removed the hacky start code check we actually didn't took into
account that *all* VRAM pages needs to be CPU accessible.

Clean up the code and unify the handling into a single helper which
checks if the whole resource is CPU accessible.

The only place where a partial check would make sense is during
eviction, but that is neglitible.

Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: aed01a68047b ("drm/amdgpu: Remove TTM resource->start visible VRAM condition v2")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org

The majority of those where removed in the commit aed01a68047b
("drm/amdgpu: Remove TTM resource->start visible VRAM condition v2")

But this one was missed because it's working on the resource and not the
BO. Since we also no longer use a fake start address for visible BOs
this will now trigger invalid mapping errors.

v2: also remove the unused variable

Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: aed01a68047b ("drm/amdgpu: Remove TTM resource->start visible VRAM condition v2")
CC: stable@vger.kernel.org
Acked-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>