Add support for RAS table at I2C EEPROM address of 0x40000, since on some
ASICs it is not at 0, but at 0x40000.

Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Kent Russell <kent.russell@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Tested-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Abstract RAS I2C EEPROM addresses from chip names, and set their macro
definition names to the address they set, not the chip they attach
to. Since most chips either use I2C EEPROM address 0 or 40000h for the RAS
table start offset, this leaves us with only two macro definitions as
opposed to five, and removes the redundancy of four.

Cc: Candice Li <candice.li@amd.com>
Cc: Tao Zhou <tao.zhou1@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove redundant EEPROM_I2C_MADDR_54H address, since we already have it
represented (ARCTURUS), and since we don't include the I2C device type
identifier in EEPROM memory addresses, i.e. that high up in the device
abstraction--we only use EEPROM memory addresses, as memory is continuously
represented by EEPROM device(s) on the I2C bus.

Add a comment describing what these memory addresses are, how they come
about and how they're usually extracted from the device address byte.

Cc: Candice Li <candice.li@amd.com>
Cc: Tao Zhou <tao.zhou1@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Fixes: c9bdc6c3cf39df ("drm/amdgpu: Add EEPROM I2C address support for ip discovery")
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1. Update EEPROM_I2C_MADDR_SMU_13_0_0 to EEPROM_I2C_MADDR_54H
2. Add EEPROM I2C address support for smu v13_0_0 and v13_0_10.

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable RAS EEPROM support for smu v13_0_0 and v13_0_10.

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Set correct EEPROM I2C address for smu v13_0_0.

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It should notice SMU to update bad channel info when detected
uncorrectable error in UMC block

Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm-misc-next for v5.18:

UAPI Changes:

Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
  and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.

Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
  advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.

Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
  bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.

Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/686ec871-e77f-c230-22e5-9e3bb80f064a@linux.intel.com

The OOB table error count info should be reset after reset
eeprom table

Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We want single instance of reset sem across all
reset clients because in case of XGMI we should stop
access cross device MMIO because any of them could be
in a reset in the moment.

Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://www.spinics.net/lists/amd-gfx/msg74117.html