linux-stable.git/drivers/gpio, branch v4.4.192 Linux kernel stable tree gpio: omap: ensure irq is enabled before wakeup 2019-08-04T07:34:45+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-06-10T17:10:44+00:00 56af78dffdaf5b07151b2cc18188b6217bba49f3 [ Upstream commit c859e0d479b3b4f6132fc12637c51e01492f31f6 ] Documentation states: NOTE: There must be a correlation between the wake-up enable and interrupt-enable registers. If a GPIO pin has a wake-up configured on it, it must also have the corresponding interrupt enabled (on one of the two interrupt lines). Ensure that this condition is always satisfied by enabling the detection events after enabling the interrupt, and disabling the detection before disabling the interrupt. This ensures interrupt/wakeup events can not happen until both the wakeup and interrupt enables correlate. If we do any clearing, clear between the interrupt enable/disable and trigger setting. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit c859e0d479b3b4f6132fc12637c51e01492f31f6 ]

Documentation states:

  NOTE: There must be a correlation between the wake-up enable and
  interrupt-enable registers. If a GPIO pin has a wake-up configured
  on it, it must also have the corresponding interrupt enabled (on
  one of the two interrupt lines).

Ensure that this condition is always satisfied by enabling the detection
events after enabling the interrupt, and disabling the detection before
disabling the interrupt.  This ensures interrupt/wakeup events can not
happen until both the wakeup and interrupt enables correlate.

If we do any clearing, clear between the interrupt enable/disable and
trigger setting.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
gpio: omap: fix lack of irqstatus_raw0 for OMAP4 2019-08-04T07:34:45+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-06-10T17:10:45+00:00 b1d99aabd239023366eabb6d3b960c0a1f92efe4 [ Upstream commit 64ea3e9094a1f13b96c33244a3fb3a0f45690bd2 ] Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added the register definition tables to the gpio-omap driver. Subsequently to that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()") added definitions for irqstatus_raw* registers to the legacy OMAP4 definitions, but missed the DT definitions. This causes an unintentional change of behaviour for the 1.101 errata workaround on OMAP4 platforms. Fix this oversight. Fixes: 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 64ea3e9094a1f13b96c33244a3fb3a0f45690bd2 ]

Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added
the register definition tables to the gpio-omap driver. Subsequently to
that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx()
checks from *_runtime_resume()") added definitions for irqstatus_raw*
registers to the legacy OMAP4 definitions, but missed the DT
definitions.

This causes an unintentional change of behaviour for the 1.101 errata
workaround on OMAP4 platforms. Fix this oversight.

Fixes: 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
gpio: fix gpio-adp5588 build errors 2019-06-22T06:18:26+00:00 Randy Dunlap rdunlap@infradead.org 2019-05-23T22:00:41+00:00 0bb6c295e463e8557a2f7fdb1f17d9672e007fa8 [ Upstream commit e9646f0f5bb62b7d43f0968f39d536cfe7123b53 ] The gpio-adp5588 driver uses interfaces that are provided by GPIOLIB_IRQCHIP, so select that symbol in its Kconfig entry. Fixes these build errors: ../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_handler’: ../drivers/gpio/gpio-adp5588.c:266:26: error: ‘struct gpio_chip’ has no member named ‘irq’ dev->gpio_chip.irq.domain, gpio)); ^ ../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_setup’: ../drivers/gpio/gpio-adp5588.c:298:2: error: implicit declaration of function ‘gpiochip_irqchip_add_nested’ [-Werror=implicit-function-declaration] ret = gpiochip_irqchip_add_nested(&dev->gpio_chip, ^ ../drivers/gpio/gpio-adp5588.c:307:2: error: implicit declaration of function ‘gpiochip_set_nested_irqchip’ [-Werror=implicit-function-declaration] gpiochip_set_nested_irqchip(&dev->gpio_chip, ^ Fixes: 459773ae8dbb ("gpio: adp5588-gpio: support interrupt controller") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: linux-gpio@vger.kernel.org Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit e9646f0f5bb62b7d43f0968f39d536cfe7123b53 ]

The gpio-adp5588 driver uses interfaces that are provided by
GPIOLIB_IRQCHIP, so select that symbol in its Kconfig entry.

Fixes these build errors:

../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_handler’:
../drivers/gpio/gpio-adp5588.c:266:26: error: ‘struct gpio_chip’ has no member named ‘irq’
            dev->gpio_chip.irq.domain, gpio));
                          ^
../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_setup’:
../drivers/gpio/gpio-adp5588.c:298:2: error: implicit declaration of function ‘gpiochip_irqchip_add_nested’ [-Werror=implicit-function-declaration]
  ret = gpiochip_irqchip_add_nested(&dev->gpio_chip,
  ^
../drivers/gpio/gpio-adp5588.c:307:2: error: implicit declaration of function ‘gpiochip_set_nested_irqchip’ [-Werror=implicit-function-declaration]
  gpiochip_set_nested_irqchip(&dev->gpio_chip,
  ^

Fixes: 459773ae8dbb ("gpio: adp5588-gpio: support interrupt controller")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
gpio: gpio-omap: add check for off wake capable gpios 2019-06-22T06:18:21+00:00 Tony Lindgren tony@atomide.com 2019-03-25T22:43:18+00:00 533171620cd52f2b99cd4f820150eeef2ba157f8 [ Upstream commit da38ef3ed10a09248e13ae16530c2c6d448dc47d ] We are currently assuming all GPIOs are non-wakeup capable GPIOs as we not configuring the bank->non_wakeup_gpios like we used to earlier with platform_data. Let's add omap_gpio_is_off_wakeup_capable() to make the handling clearer while considering that later patches may want to configure SoC specific bank->non_wakeup_gpios for the GPIOs in wakeup domain. Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Tero Kristo <t-kristo@ti.com> Reported-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit da38ef3ed10a09248e13ae16530c2c6d448dc47d ]

We are currently assuming all GPIOs are non-wakeup capable GPIOs as we
not configuring the bank->non_wakeup_gpios like we used to earlier with
platform_data.

Let's add omap_gpio_is_off_wakeup_capable() to make the handling clearer
while considering that later patches may want to configure SoC specific
bank->non_wakeup_gpios for the GPIOs in wakeup domain.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
gpio: gpio-omap: fix level interrupt idling 2019-04-27T07:33:48+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-03-01T19:02:52+00:00 28833fee9f4a4deb5bffefd7afb22d0e8cd0ed4e [ Upstream commit d01849f7deba81f4959fd9e51bf20dbf46987d1c ] Tony notes that the GPIO module does not idle when level interrupts are in use, as the wakeup appears to get stuck. After extensive investigation, it appears that the wakeup will only be cleared if the interrupt status register is cleared while the interrupt is enabled. However, we are currently clearing it with the interrupt disabled for level-based interrupts. It is acknowledged that this observed behaviour conflicts with a statement in the TRM: CAUTION After servicing the interrupt, the status bit in the interrupt status register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be reset and the interrupt line released (by setting the corresponding bit of the interrupt status register to 1) before enabling an interrupt for the GPIO channel in the interrupt-enable register (GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent the occurrence of unexpected interrupts when enabling an interrupt for the GPIO channel. However, this does not appear to be a practical problem. Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>, the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP: Fix the sequence to clear the IRQ status" saying: if the status is cleared after disabling the IRQ then sWAKEUP will not be cleared and gates the module transition When we unmask the level interrupt after the interrupt has been handled, enable the interrupt and only then clear the interrupt. If the interrupt is still pending, the hardware will re-assert the interrupt status. Should the caution note in the TRM prove to be a problem, we could use a clear-enable-clear sequence instead. Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Keerthy <j-keerthy@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> [tony@atomide.com: updated comments based on an earlier TI patch] Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit d01849f7deba81f4959fd9e51bf20dbf46987d1c ]

Tony notes that the GPIO module does not idle when level interrupts are
in use, as the wakeup appears to get stuck.

After extensive investigation, it appears that the wakeup will only be
cleared if the interrupt status register is cleared while the interrupt
is enabled. However, we are currently clearing it with the interrupt
disabled for level-based interrupts.

It is acknowledged that this observed behaviour conflicts with a
statement in the TRM:

CAUTION
  After servicing the interrupt, the status bit in the interrupt status
  register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be
  reset and the interrupt line released (by setting the corresponding
  bit of the interrupt status register to 1) before enabling an
  interrupt for the GPIO channel in the interrupt-enable register
  (GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent
  the occurrence of unexpected interrupts when enabling an interrupt
  for the GPIO channel.

However, this does not appear to be a practical problem.

Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>,
the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP:
Fix the sequence to clear the IRQ status" saying:

 if the status is cleared after disabling the IRQ then sWAKEUP will not
 be cleared and gates the module transition

When we unmask the level interrupt after the interrupt has been handled,
enable the interrupt and only then clear the interrupt. If the interrupt
is still pending, the hardware will re-assert the interrupt status.

Should the caution note in the TRM prove to be a problem, we could
use a clear-enable-clear sequence instead.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated comments based on an earlier TI patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
gpio: adnp: Fix testing wrong value in adnp_gpio_direction_input 2019-04-03T04:23:28+00:00 Axel Lin axel.lin@ingics.com 2019-03-11T13:29:37+00:00 e250a5ac0e12ddba89d2ece260d167999af8a7c2 commit c5bc6e526d3f217ed2cc3681d256dc4a2af4cc2b upstream. Current code test wrong value so it does not verify if the written data is correctly read back. Fix it. Also make it return -EPERM if read value does not match written bit, just like it done for adnp_gpio_direction_output(). Fixes: 5e969a401a01 ("gpio: Add Avionic Design N-bit GPIO expander support") Cc: <stable@vger.kernel.org> Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c5bc6e526d3f217ed2cc3681d256dc4a2af4cc2b upstream.

Current code test wrong value so it does not verify if the written
data is correctly read back. Fix it.
Also make it return -EPERM if read value does not match written bit,
just like it done for adnp_gpio_direction_output().

Fixes: 5e969a401a01 ("gpio: Add Avionic Design N-bit GPIO expander support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gpio: vf610: Mask all GPIO interrupts 2019-03-23T07:44:25+00:00 Andrew Lunn andrew@lunn.ch 2019-01-27T21:58:00+00:00 35709d6424884c90483b61a14708680fc94ab36e [ Upstream commit 7ae710f9f8b2cf95297e7bbfe1c09789a7dc43d4 ] On SoC reset all GPIO interrupts are disable. However, if kexec is used to boot into a new kernel, the SoC does not experience a reset. Hence GPIO interrupts can be left enabled from the previous kernel. It is then possible for the interrupt to fire before an interrupt handler is registered, resulting in the kernel complaining of an "unexpected IRQ trap", the interrupt is never cleared, and so fires again, resulting in an interrupt storm. Disable all GPIO interrupts before registering the GPIO IRQ chip. Fixes: 7f2691a19627 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 7ae710f9f8b2cf95297e7bbfe1c09789a7dc43d4 ]

On SoC reset all GPIO interrupts are disable. However, if kexec is
used to boot into a new kernel, the SoC does not experience a
reset. Hence GPIO interrupts can be left enabled from the previous
kernel. It is then possible for the interrupt to fire before an
interrupt handler is registered, resulting in the kernel complaining
of an "unexpected IRQ trap", the interrupt is never cleared, and so
fires again, resulting in an interrupt storm.

Disable all GPIO interrupts before registering the GPIO IRQ chip.

Fixes: 7f2691a19627 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
gpio: max7301: fix driver for use with CONFIG_VMAP_STACK 2019-01-13T09:05:27+00:00 Christophe Leroy christophe.leroy@c-s.fr 2018-12-07T13:07:55+00:00 61b4285244c1c910d3527090b49c5908beb92bf5 commit abf221d2f51b8ce7b9959a8953f880a8b0a1400d upstream. spi_read() and spi_write() require DMA-safe memory. When CONFIG_VMAP_STACK is selected, those functions cannot be used with buffers on stack. This patch replaces calls to spi_read() and spi_write() by spi_write_then_read() which doesn't require DMA-safe buffers. Fixes: 0c36ec314735 ("gpio: gpio driver for max7301 SPI GPIO expander") Cc: <stable@vger.kernel.org> Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit abf221d2f51b8ce7b9959a8953f880a8b0a1400d upstream.

spi_read() and spi_write() require DMA-safe memory. When
CONFIG_VMAP_STACK is selected, those functions cannot be used
with buffers on stack.

This patch replaces calls to spi_read() and spi_write() by
spi_write_then_read() which doesn't require DMA-safe buffers.

Fixes: 0c36ec314735 ("gpio: gpio driver for max7301 SPI GPIO expander")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gpio: msic: fix error return code in platform_msic_gpio_probe() 2018-11-10T15:41:39+00:00 Gustavo A. R. Silva gustavo@embeddedor.com 2017-08-03T22:00:01+00:00 7f71f461af4a3e8e29e543d15fca150a2057faf4 [ Upstream commit ca1f3ae3154ad6d08caa740c99be0d86644a4e44 ] platform_get_irq() returns an error code, but the gpio-msic driver ignores it and always returns -EINVAL. This is not correct, and prevents -EPROBE_DEFER from being propagated properly. Notice that platform_get_irq() no longer returns 0 on error: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af Print and propagate the return value of platform_get_irq on failure. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit ca1f3ae3154ad6d08caa740c99be0d86644a4e44 ]

platform_get_irq() returns an error code, but the gpio-msic driver
ignores it and always returns -EINVAL. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.

Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af

Print and propagate the return value of platform_get_irq on failure.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
gpio: adp5588: Fix sleep-in-atomic-context bug 2018-10-10T06:52:10+00:00 Michael Hennerich michael.hennerich@analog.com 2018-08-13T13:57:44+00:00 880b5a109a50a8a15ff355de2f64e91bc9d8710c [ Upstream commit 6537886cdc9a637711fd6da980dbb87c2c87c9aa ] This fixes: [BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug in adp5588_gpio_write() [BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug in adp5588_gpio_direction_input() Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit 6537886cdc9a637711fd6da980dbb87c2c87c9aa ]

This fixes:
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
                          in adp5588_gpio_write()
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
                          in adp5588_gpio_direction_input()

Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>