Since commit ab82fa7da4dce5c7 ("gpio: rcar: Prevent module clock disable
when wake-up is enabled"), when a GPIO is used for wakeup, the GPIO
block's module clock (if exists) is manually kept running during system
suspend, to make sure the device stays active.

However, this explicit clock handling is merely a workaround for a
failure to properly communicate wakeup information to the device core.

Instead, set the device's power.wakeup_path field, to indicate this
device is part of the wakeup path.  Depending on the PM Domain's
active_wakeup configuration, the genpd core code will keep the device
enabled (and the clock running) during system suspend when needed.
This allows for the removal of all explicit clock handling code from the
driver.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

of_get_named_gpiod_flags() used directly in of_find_gpio() or indirectly
through of_find_spi_gpio() or of_find_regulator_gpio() can return
-EPROBE_DEFER. This gets overwritten by the subsequent of_find_*_gpio()
calls.

This patch fixes this by trying of_find_spi_gpio() or
of_find_regulator_gpio() only if deferred probing was not requested by
the previous of_get_named_gpiod_flags() call.

Fixes: 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO properties")
Fixes: c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[Augmented to fit with Maxime's patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commits c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
and 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO
properties") have introduced a regression in the way error codes from
of_get_named_gpiod_flags are handled.

Previously, those errors codes were returned immediately, but the two
commits mentioned above are now overwriting the error pointer, meaning that
whatever value has been returned will be dropped in favor of whatever the
two new functions will return.

This might not be a big deal except for EPROBE_DEFER, on which GPIOlib
customers will depend on, and that will now be returned as an hard error
which means that they will not probe anymore, instead of gently deferring
their probe.

Since EPROBE_DEFER basically means that we have found a valid property but
there was no GPIO controller registered to handle it, fix this issues by
returning it as soon as we encounter it.

Fixes: c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
Fixes: 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO properties")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[Fold in fix to the fix]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.

Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.16 kernel cycle.
  Like with GPIO it is actually a bit calm this time.

  Core changes:

   - After lengthy discussions and partly due to my ignorance, we have
     merged a patch making pinctrl_force_default() and
     pinctrl_force_sleep() reprogram the states into the hardware of any
     hogged pins, even if they are already in the desired state.

     This only apply to hogged pins since groups of pins owned by
     drivers need to be managed by each driver, lest they could not do
     things like runtime PM and put pins to sleeping state even if the
     system as a whole is not in sleep.

  New drivers:

   - New driver for the Microsemi Ocelot SoC. This is used in ethernet
     switches.

   - The X-Powers AXP209 GPIO driver was extended to also deal with pin
     control and moved over from the GPIO subsystem. This circuit is a
     mixed-mode integrated circuit which is part of AllWinner designs.

   - New subdriver for the Qualcomm MSM8998 SoC, core of a high end
     mobile devices (phones) chipset.

   - New subdriver for the ST Microelectronics STM32MP157 MPU and
     STM32F769 MCU from the STM32 family.

   - New subdriver for the MediaTek MT7622 SoC. This is used for
     routers, repeater, gateways and such network infrastructure.

   - New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC
     has multimedia features and target "smart devices", I guess in-car
     entertainment, in-flight entertainment, industrial control panels
     etc.

  General improvements:

   - Incremental improvements on the SH-PFC subdrivers for things like
     the CAN bus.

   - Enable the glitch filter on Baytrail GPIOs used for interrupts.

   - Proper handling of pins to GPIO ranges on the Semtec SX150X

   - An IRQ setup ordering fix on MCP23S08.

   - A good set of janitorial coding style fixes"

* tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (102 commits)
  pinctrl: mcp23s08: fix irq setup order
  pinctrl: Forward declare struct device
  pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
  pinctrl: stm32: add STM32F769 MCU support
  pinctrl: sx150x: Add a static gpio/pinctrl pin range mapping
  pinctrl: sx150x: Register pinctrl before adding the gpiochip
  pinctrl: sx150x: Unregister the pinctrl on release
  pinctrl: ingenic: Remove redundant dev_err call in ingenic_pinctrl_probe()
  pinctrl: sprd: Use seq_putc() in sprd_pinconf_group_dbg_show()
  pinctrl: pinmux: Use seq_putc() in pinmux_pins_show()
  pinctrl: abx500: Use seq_putc() in abx500_gpio_dbg_show()
  pinctrl: mediatek: mt7622: align error handling of mtk_hw_get_value call
  pinctrl: mediatek: mt7622: fix potential uninitialized value being returned
  pinctrl: uniphier: refactor drive strength get/set functions
  pinctrl: imx7ulp: constify struct imx_cfg_params_decode
  pinctrl: imx: constify struct imx_pinctrl_soc_info
  pinctrl: imx7d: simplify imx7d_pinctrl_probe
  pinctrl: imx: use struct imx_pinctrl_soc_info as a const
  pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly.
  pinctrl: qcom: Add msm8998 pinctrl driver
  ...

Pull GPIO updates from Linus Walleij:
 "The is the bulk of GPIO changes for the v4.16 kernel cycle. It is
  pretty calm this time around I think. I even got time to get to things
  like starting to clean up header includes.

  Core changes:

   - Disallow open drain and open source flags to be set simultaneously.
     This doesn't make electrical sense, and would the hardware actually
     respond to this setting, the result would be short circuit.

   - ACPI GPIO has a new core infrastructure for handling quirks. The
     quirks are there to deal with broken ACPI tables centrally instead
     of pushing the work to individual drivers. In the world of BIOS
     writers, the ACPI tables are perfect. Until they find a mistake in
     it. When such a mistake is found, we can patch it with a quirk. It
     should never happen, the problem is that it happens. So we
     accomodate for it.

   - Several documentation updates.

   - Revert the patch setting up initial direction state from reading
     the device. This was causing bad things for drivers that can't read
     status on all its pins. It is only affecting debugfs information
     quality.

   - Label descriptors with the device name if no explicit label is
     passed in.

   - Pave the ground for transitioning SPI and regulators to use GPIO
     descriptors by implementing some quirks in the device tree GPIO
     parsing code.

  New drivers:

   - New driver for the Access PCIe IDIO 24 family.

  Other:

   - Major refactorings and improvements to the GPIO mockup driver used
     for test and verification.

   - Moved the AXP209 driver over to pin control since it gained a pin
     control back-end. These patches will appear (with the same hashes)
     in the pin control pull request as well.

   - Convert the onewire GPIO driver w1-gpio to use descriptors. This is
     merged here since the W1 maintainers send very few pull requests
     and he ACKed it.

   - Start to clean up driver headers using <linux/gpio.h> to just use
     <linux/gpio/driver.h> as appropriate"

* tag 'gpio-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (103 commits)
  gpio: Timestamp events in hardirq handler
  gpio: Fix kernel stack leak to userspace
  gpio: Fix a documentation spelling mistake
  gpio: Documentation update
  gpiolib: remove redundant initialization of pointer desc
  gpio: of: Fix NPE from OF flags
  gpio: stmpe: Delete an unnecessary variable initialisation in stmpe_gpio_probe()
  gpio: stmpe: Move an assignment in stmpe_gpio_probe()
  gpio: stmpe: Improve a size determination in stmpe_gpio_probe()
  gpio: stmpe: Use seq_putc() in stmpe_dbg_show()
  gpio: No NULL owner
  gpio: stmpe: i2c transfer are forbiden in atomic context
  gpio: davinci: Include proper header
  gpio: da905x: Include proper header
  gpio: cs5535: Include proper header
  gpio: crystalcove: Include proper header
  gpio: bt8xx: Include proper header
  gpio: bcm-kona: Include proper header
  gpio: arizona: Include proper header
  gpio: amd8111: Include proper header
  ...

Pull poll annotations from Al Viro:
 "This introduces a __bitwise type for POLL### bitmap, and propagates
  the annotations through the tree. Most of that stuff is as simple as
  'make ->poll() instances return __poll_t and do the same to local
  variables used to hold the future return value'.

  Some of the obvious brainos found in process are fixed (e.g. POLLIN
  misspelled as POLL_IN). At that point the amount of sparse warnings is
  low and most of them are for genuine bugs - e.g. ->poll() instance
  deciding to return -EINVAL instead of a bitmap. I hadn't touched those
  in this series - it's large enough as it is.

  Another problem it has caught was eventpoll() ABI mess; select.c and
  eventpoll.c assumed that corresponding POLL### and EPOLL### were
  equal. That's true for some, but not all of them - EPOLL### are
  arch-independent, but POLL### are not.

  The last commit in this series separates userland POLL### values from
  the (now arch-independent) kernel-side ones, converting between them
  in the few places where they are copied to/from userland. AFAICS, this
  is the least disruptive fix preserving poll(2) ABI and making epoll()
  work on all architectures.

  As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
  it will trigger only on what would've triggered EPOLLWRBAND on other
  architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
  at all on sparc. With this patch they should work consistently on all
  architectures"

* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
  make kernel-side POLL... arch-independent
  eventpoll: no need to mask the result of epi_item_poll() again
  eventpoll: constify struct epoll_event pointers
  debugging printk in sg_poll() uses %x to print POLL... bitmap
  annotate poll(2) guts
  9p: untangle ->poll() mess
  ->si_band gets POLL... bitmap stored into a user-visible long field
  ring_buffer_poll_wait() return value used as return value of ->poll()
  the rest of drivers/*: annotate ->poll() instances
  media: annotate ->poll() instances
  fs: annotate ->poll() instances
  ipc, kernel, mm: annotate ->poll() instances
  net: annotate ->poll() instances
  apparmor: annotate ->poll() instances
  tomoyo: annotate ->poll() instances
  sound: annotate ->poll() instances
  acpi: annotate ->poll() instances
  crypto: annotate ->poll() instances
  block: annotate ->poll() instances
  x86: annotate ->poll() instances
  ...

Pull sound updates from Takashi Iwai:
 "The major changes in the core API side in this cycle are the still
  on-going ASoC componentization works. Other than that, only few small
  changes such as 20bit PCM format support are found.

  Meanwhile the rest majority of changes are for ASoC drivers:

   - Large cleanups of some of the TI CODEC drivers

   - Continued work on Intel ASoC stuff for new quirks, ACPI GPIO
     handling, Kconfigs and lots of cleanups

   - Refactoring of the Freescale SSI driver, as preliminary work for
     the upcoming changes

   - Work on ST DFSDM driver, including the required IIO patches

   - New drivers for Allwinner A83T, Maxim MAX89373, SocioNext UiniPhier
     EVEA Tempo Semiconductor TSCS42xx and TI PCM816x, TAS5722 and
     TAS6424 devices

   - Removal of dead codes for SN95031 and board drivers

  Last but not least, a few HD-audio and USB-audio quirks are included
  as usual, too"

* tag 'sound-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (303 commits)
  ALSA: hda - Reduce the suspend time consumption for ALC256
  ASoC: use seq_file to dump the contents of dai_list,platform_list and codec_list
  ASoC: soc-core: add missing EXPORT_SYMBOL_GPL() for snd_soc_rtdcom_lookup
  IIO: ADC: stm32-dfsdm: remove unused variable again
  ASoC: bcm2835: fix hw_params error when device is in prepared state
  ASoC: mxs-sgtl5000: Do not print error on probe deferral
  ASoC: sgtl5000: Do not print error on probe deferral
  ASoC: Intel: remove select on non-existing SND_SOC_INTEL_COMMON
  ALSA: usb-audio: Support changing input on Sound Blaster E1
  ASoC: Intel: remove second duplicated assignment to pointer 'res'
  ALSA: hda/realtek - update ALC215 depop optimize
  ALSA: hda/realtek - Support headset mode for ALC215/ALC285/ALC289
  ALSA: pcm: Fix trailing semicolon
  ASoC: add Component level .read/.write
  ASoC: cx20442: fix regression by adding back .read/.write
  ASoC: uda1380: fix regression by adding back .read/.write
  ASoC: tlv320dac33: fix regression by adding back .read/.write
  ALSA: hda - Use IS_REACHABLE() for dependency on input
  IIO: ADC: stm32-dfsdm: fix static check warning
  IIO: ADC: stm32-dfsdm: code optimization
  ...

Add a hardirq handler to the GPIO userspace event loop, making
sure to pick up the timestamp there, as close as possible in time
relative to the actual event causing the interrupt.

Tested with a simple pushbutton GPIO on ux500 and seems to work
fine.

Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reported-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The GPIO event descriptor was leaking kernel stack to
userspace because we don't zero the variable before
use. Ooops. Fix this.

Cc: stable@vger.kernel.org
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>