Added support to Zynq Ultrascale+ MPSoC on the existing zynq
gpio driver.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add a GPIO driver for the General I/O block on Axis ETRAX FS SoCs.

Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for the GPIO IP "UPG GIO" used on
Broadcom STB SoCs (BCM7XXX and some others). Uses
basic_mmio_gpio to instantiate a gpio_chip for each bank.
The driver assumes that it handles the base set of GPIOs
on the system and that it can start its numbering sequence
from 0, so any GPIO expanders used with it must dynamically
assign GPIO numbers after this driver has finished
registering its GPIOs.

Does not implement the interrupt-controller portion yet,
will be done in a future commit.

v2:
- change include to use <linux/gpio/driver.h> instead of
  <linux/gpio.h>
- get rid of unnecessary imask member in struct bank
- rename GPIO_PER_BANK -> MAX_GPIO_PER_BANK
- always have 32 GPIOs per bank and add 'width' member in
  struct bank to hold actual number of GPIOs in use
- mark of_match table as const

List-usage-fixed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add GPIO controller driver for Netlogic XLP MIPS64 SOCs.

This driver is instantiated by device tree and supports interrupts
for GPIOs.

Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We currently get all kinds of errors building the omap gpio driver
as a module starting with:

undefined reference to `omap2_gpio_resume_after_idle'
undefined reference to `omap2_gpio_prepare_for_idle'
...

Let's fix the issue by adding inline functions to the header.
Note that we can now also remove the two unused functions for
omap_set_gpio_debounce and omap_set_gpio_debounce_time.

Then doing rmmod on the module produces further warnings
because of missing exit related functions. Let's add those.

And finally, we can make the Kconfig entry just a tristate
option that's selected for omaps.

Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Driver for the GPIO block found on NXP LPC18xx/43xx devices.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull ARM SoC cleanups from Olof Johansson:
 "We've got a fairly large cleanup branch this time.  The bulk of this
  is removal of non-DT platforms of several flavors:

   - Atmel at91 platforms go full-DT, with removal of remaining
     board-file based support

   - OMAP removes legacy board files for three more platforms

   - removal of non-DT mach-msm, newer Qualcomm platforms now live in
     mach-qcom

   - Freescale i.MX25 also removes non-DT platform support"

Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
  mmc: Remove msm_sdcc driver
  gpio: Remove gpio-msm-v1 driver
  ARM: Remove mach-msm and associated ARM architecture code
  ARM: shmobile: cpuidle: Remove the pointless default driver
  ARM: davinci: dm646x: Add interrupt resource for McASPs
  ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
  ARM: davinci: dm646x: Clean up the McASP DMA resources
  ARM: davinci: devices-da8xx: Add support for McASP2 on da830
  ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
  ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
  ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
  ARM: OMAP2+: Remove legacy support for omap3 TouchBook
  ARM: OMAP3: Remove legacy support for devkit8000
  ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
  ARM: shmobile: Consolidate the pm code for R-Car Gen2
  ARM: shmobile: r8a7791: Correct SYSCIER value
  ARM: shmobile: r8a7790: Correct SYSCIER value
  ARM: at91: remove old setup
  ARM: at91: sama5d4: remove useless map_io
  ARM: at91: sama5 use SoC detection infrastructure
  ...

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.1 development cycle:

   - A new GPIO hogging mechanism has been added.  This can be used on
     boards that want to drive some GPIO line high, low, or set it as
     input on boot and then never touch it again.  For some embedded
     systems this is bliss and simplifies things to a great extent.

   - Some API cleanup and closure: gpiod_get_array() and
     gpiod_put_array() has been added to get and put GPIOs in bulk as
     was possible with the non-descriptor API.

   - Encapsulate cross-calls to the pin control subsystem in
     <linux/gpio/driver.h>.  Now this should be the only header any GPIO
     driver needs to include or something is wrong.  Cleanups
     restricting drivers to this include are welcomed if tested.

   - Sort the GPIO Kconfig and split it into submenus, as it was
     becoming and unstructured, illogical and unnavigatable mess.  I
     hope this is easier to follow.  Menus that require a certain
     subsystem like I2C can now be hidden nicely for example, still
     working on others.

   - New drivers:

       - New driver for the Altera Soft GPIO.

       - The F7188x driver now handles the F71869 and F71869A variants.

       - The MIPS Loongson driver has been moved to drivers/gpio for
         consolidation and cleanup.

   - Cleanups:

       - The MAX732x is converted to use the GPIOLIB_IRQCHIP
         infrastructure.

       - The PCF857x is converted to use the GPIOLIB_IRQCHIP
         infrastructure.

       - Radical cleanup of the OMAP driver.

   - Misc:

       - Enable the DWAPB GPIO for all architectures.  This is a "hard
         IP" block from Synopsys which has started to turn up in so
         diverse architectures as X86 Quark, ARC and a slew of ARM
         systems.  So even though it's not an expander, it's generic
         enough to be available for all.

       - We add a mock GPIO on Crystalcove PMIC after a long discussion
         with Daniel Vetter et al, tracing back to the shootout at the
         kernel summit where DRM drivers and sub-componentization was
         discussed.  In this case a mock GPIO is assumed to be the best
         compromise gaining some reuse of infrastructure without making
         DRM drivers overly complex at the same time.  Let's see"

* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
  Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
  gpio: dwapb: remove dependencies
  gpio: dwapb: enable for ARC
  gpio: removing kfree remove functionality
  gpio: mvebu: Fix mask/unmask managment per irq chip type
  gpio: split GPIO drivers in submenus
  gpio: move MFD GPIO drivers under their own comment
  gpio: move BCM Kona Kconfig option
  gpio: arrange SPI Kconfig symbols alphabetically
  gpio: arrange PCI GPIO controllers alphabetically
  gpio: arrange I2C Kconfig symbols alphabetically
  gpio: arrange Kconfig symbols alphabetically
  gpio: ich: Implement get_direction function
  gpio: use (!foo) instead of (foo == NULL)
  gpio: arizona: drop owner assignment from platform_drivers
  gpio: max7300: remove 'ret' variable
  gpio: use devm_kzalloc
  gpio: sch: use uapi/linux/pci_ids.h directly
  gpio: x-gene: fix devm_ioremap_resource() check
  gpio: loongson: Add Loongson-3A/3B GPIO driver support
  ...

The Synopsys DesignWare DWAPB GPIO block is popular to
synthesize amongst many architectures: X86, ARM, ARC.
The driver was restricted to only these archs due to
using [read|write]l_relaxed() accessors that were not
universally available in the past,
but as of commit 9439eb3ab9d1ece6e4ad7baaa4a7f534f9b9dab0
"asm-generic: io: implement relaxed accessor macros as
conditional wrappers" these accessors are available on all
archs so this should not be a problem any more. Enable the
driver for all archs.

Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Synopsys SDP platform uses DW GPIO controller in design with
ARC cores. So adding ARC to architectures that may select this
GPIO controller.

Even though support for Synopsys SDP is yet to be submitted we'll need
this tiny option enabled at least for properly working interrupts (DW
GPIO controller is used as interrupt controller).

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>