linux-stable.git/drivers/dma, branch v4.9.91

dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63

2018-03-24T10:00:26+00:00

[ Upstream commit d087f15786021a9605b20f4c678312510be4cac1 ]

Register layout of a typical TPCC_EVT_MUX_M_N register is such that the
lowest numbered event is at the lowest byte address and highest numbered
event at highest byte address. But TPCC_EVT_MUX_60_63 register layout is
different,  in that the lowest numbered event is at the highest address
and highest numbered event is at the lowest address. Therefore, modify
ti_am335x_xbar_write() to handle TPCC_EVT_MUX_60_63 register
accordingly.

Signed-off-by: Vignesh R 
Signed-off-by: Peter Ujfalusi 
Signed-off-by: Vinod Koul 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

dmaengine: zynqmp_dma: Fix race condition in the probe

2018-03-24T10:00:24+00:00

[ Upstream commit 5ba080aada5e739165e0f38d5cc3b04c82b323c8 ]

Incase of interrupt property is not present,
Driver is trying to free an invalid irq,
This patch fixes it by adding a check before freeing the irq.

Signed-off-by: Kedareswara rao Appana 
Signed-off-by: Vinod Koul 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

dmaengine: imx-sdma: add 1ms delay to ensure SDMA channel is stopped

2018-03-22T08:17:43+00:00

[ Upstream commit 7f3ff14b7eb1ffad132117f08a1973b48e653d43 ]

sdma_disable_channel() cannot ensure dma is stopped to access
module's FIFOs. There is chance SDMA core is running and accessing
BD when disable of corresponding channel, this may cause sometimes
even after call of .sdma_disable_channel(), SDMA core still be
running and accessing module's FIFOs.

According to NXP R&D team a delay of one BD SDMA cost time (maximum
is 1ms) should be added after disable of the channel bit, to ensure
SDMA core has really been stopped after SDMA clients call
.device_terminate_all.

This patch introduces adds a new function sdma_disable_channel_with_delay()
which simply adds 1ms delay after call sdma_disable_channel(),
and set it as .device_terminate_all.

Signed-off-by: Jiada Wang 
Signed-off-by: Vinod Koul 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

dmaengine: fsl-edma: disable clks on all error paths

2018-03-03T09:23:20+00:00

[ Upstream commit 2610acf46b9ed528ec2cacd717bc9d354e452b73 ]

Previously enabled clks are only disabled if clk_prepare_enable() fails.
However, there are other error paths were the previously enabled
clocks are not disabled.

To fix the problem, fsl_disable_clocks() now takes the number of clocks
that shall be disabled + unprepared. For existing calls were all clocks
were already successfully prepared + enabled, DMAMUX_NR is passed to
disable + unprepare all clocks.

In error paths were only some clocks were successfully prepared +
enabled the loop counter is passed, in order to disable + unprepare
all successfully prepared + enabled clocks.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Andreas Platschek 
Signed-off-by: Vinod Koul 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

dmaengine: zx: fix build warning

2018-02-25T10:05:53+00:00

commit 067fdeb2f391bfa071f741a2b3eb74b8ff3785cd upstream.

Fix build warning that related to PAGE_SIZE. The maximum DMA
length has nothing to do with PAGE_SIZE, just use a fix number
for the definition.

drivers/dma/zx_dma.c: In function 'zx_dma_prep_memcpy':
drivers/dma/zx_dma.c:523:8: warning: division by zero [-Wdiv-by-zero]
drivers/dma/zx_dma.c: In function 'zx_dma_prep_slave_sg':
drivers/dma/zx_dma.c:567:11: warning: division by zero [-Wdiv-by-zero]

Signed-off-by: Jun Nie 
Tested-by: Shawn Guo 
Signed-off-by: Vinod Koul 
Signed-off-by: Greg Kroah-Hartman

dmaengine: jz4740: disable/unprepare clk if probe fails

2018-02-25T10:05:49+00:00

[ Upstream commit eb9436966fdc84cebdf222952a99898ab46d9bb0 ]

in error path of jz4740_dma_probe(), call clk_disable_unprepare() to clean
up.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 25ce6c35fea0 MIPS: jz4740: Remove custom DMA API
Signed-off-by: Tobias Jordan 
Signed-off-by: Vinod Koul 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

dmaengine: at_hdmac: fix potential NULL pointer dereference in atc_prep_dma_interleaved

2018-02-25T10:05:48+00:00

[ Upstream commit 62a277d43d47e74972de44d33bd3763e31992414 ]

_xt_ is being dereferenced before it is null checked, hence there is a
potential null pointer dereference.

Fix this by moving the pointer dereference after _xt_ has been null
checked.

This issue was detected with the help of Coccinelle.

Fixes: 4483320e241c ("dmaengine: Use Pointer xt after NULL check.")
Signed-off-by: Gustavo A. R. Silva 
Acked-by: Ludovic Desroches 
Signed-off-by: Vinod Koul 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

dmaengine: ioat: Fix error handling path

2018-02-25T10:05:48+00:00

[ Upstream commit 5c9afbda911ce20b3f2181d1e440a0222e1027dd ]

If the last test in 'ioat_dma_self_test()' fails, we must release all
the allocated resources and not just part of them.

Signed-off-by: Christophe JAILLET 
Acked-by: Dave Jiang 
Signed-off-by: Vinod Koul 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

dmaengine: dmatest: fix container_of member in dmatest_callback

2018-02-17T12:21:12+00:00

commit 66b3bd2356e0a1531c71a3dcf96944621e25c17c upstream.

The type of arg passed to dmatest_callback is struct dmatest_done.
It refers to test_done in struct dmatest_thread, not done_wait.

Fixes: 6f6a23a213be ("dmaengine: dmatest: move callback wait ...")
Signed-off-by: Yang Shunyong 
Acked-by: Adam Wallis 
Signed-off-by: Vinod Koul 
Signed-off-by: Greg Kroah-Hartman

dmaengine: ti-dma-crossbar: Correct am335x/am43xx mux value type

2017-12-20T09:07:27+00:00

[ Upstream commit 288e7560e4d3e259aa28f8f58a8dfe63627a1bf6 ]

The used 0x1f mask is only valid for am335x family of SoC, different family
using this type of crossbar might have different number of electable
events. In case of am43xx family 0x3f mask should have been used for
example.
Instead of trying to handle each family's mask, just use u8 type to store
the mux value since the event offsets are aligned to byte offset.

Fixes: 42dbdcc6bf965 ("dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx")
Signed-off-by: Peter Ujfalusi 
Signed-off-by: Vinod Koul 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman