commit 4ee4cdad368a26de3967f2975806a9ee2fa245df upstream.

Since commit 358ba762d9f1 ("crypto: caam - enable prediction resistance
in HRWNG") the following CAAM errors can be seen on i.MX6SX:

caam_jr 2101000.jr: 20003c5b: CCB: desc idx 60: RNG: Hardware error
hwrng: no data available

This error is due to an incorrect entropy delay for i.MX6SX.

Fix it by increasing the minimum entropy delay for i.MX6SX
as done in U-Boot:
https://patchwork.ozlabs.org/project/uboot/patch/20220415111049.2565744-1-gaurav.jain@nxp.com/

As explained in the U-Boot patch:

"RNG self tests are run to determine the correct entropy delay.
Such tests are executed with different voltages and temperatures to identify
the worst case value for the entropy delay. For i.MX6SX, it was determined
that after adding a margin value of 1000 the minimum entropy delay should be
at least 12000."

Cc: <stable@vger.kernel.org>
Fixes: 358ba762d9f1 ("crypto: caam - enable prediction resistance in HRWNG")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When caam queue is full (-ENOSPC), caam frees descriptor memory.
crypto-engine checks if retry support is true and h/w queue
is full(-ENOSPC), then requeue the crypto request.
During processing the requested descriptor again, caam gives below error.
(caam_jr 30902000.jr: 40000006: DECO: desc idx 0: Invalid KEY Command).

This patch adds a check to return when caam input ring is full
and retry support is true. so descriptor memory is not freed
and requeued request can be processed again.

Fixes: 2d653936eb2cf ("crypto: caam - enable crypto-engine retry mechanism")
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When enable the kernel debug config, there is below calltrace detected:
BUG: using smp_processor_id() in preemptible [00000000] code: cryptomgr_test/339
caller is debug_smp_processor_id+0x20/0x30
CPU: 9 PID: 339 Comm: cryptomgr_test Not tainted 5.10.63-yocto-standard #1
Hardware name: NXP Layerscape LX2160ARDB (DT)
Call trace:
 dump_backtrace+0x0/0x1a0
 show_stack+0x24/0x30
 dump_stack+0xf0/0x13c
 check_preemption_disabled+0x100/0x110
 debug_smp_processor_id+0x20/0x30
 dpaa2_caam_enqueue+0x10c/0x25c
 ......
 cryptomgr_test+0x38/0x60
 kthread+0x158/0x164
 ret_from_fork+0x10/0x38
According to the comment in commit ac5d15b4519f("crypto: caam/qi2
 - use affine DPIOs "), because preemption is no longer disabled
while trying to enqueue an FQID, it might be possible to run the
enqueue on a different CPU(due to migration, when in process context),
however this wouldn't be a functionality issue. But there will be
above calltrace when enable kernel debug config. So, replace this_cpu_ptr
with raw_cpu_ptr to avoid above call trace.

Fixes: ac5d15b4519f ("crypto: caam/qi2 - use affine DPIOs")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

On newer CAAM versions, not all accelerators are disabled if the SoC is
a non-E variant. While the driver checks most of the modules for
availability, there is one - PKHA - which sticks out. On non-E variants
it is still reported as available, that is the number of instances is
non-zero, but it has limited functionality. In particular it doesn't
support encryption and decryption, but just signing and verifying. This
is indicated by a bit in the PKHA_MISC field. Take this bit into account
if we are checking for availability.

This will the following error:
[    8.167817] caam_jr 8020000.jr: 20000b0f: CCB: desc idx 11: : Invalid CHA selected.

Tested on an NXP LS1028A (non-E) SoC.

Fixes: d239b10d4ceb ("crypto: caam - add register map changes cf. Era 10")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fixes the following W=1 kernel build warning(s):

 drivers/crypto/caam/caampkc.c:199: warning: expecting prototype for from a given scatterlist(). Prototype was for caam_rsa_count_leading_zeros() instead
 drivers/crypto/caam/caamalg_qi2.c:87: warning: Function parameter or member 'xts_key_fallback' not described in 'caam_ctx'
 drivers/crypto/caam/caamalg_qi2.c:87: warning: Function parameter or member 'fallback' not described in 'caam_ctx'

Cc: "Horia Geantă" <horia.geanta@nxp.com>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fix the following coccicheck warning:

./drivers/crypto/caam/debugfs.c:23:0-23: WARNING: caam_fops_u64_ro
should be defined with DEFINE_DEBUGFS_ATTRIBUTE.

./drivers/crypto/caam/debugfs.c:22:0-23: WARNING: caam_fops_u32_ro
should be defined with DEFINE_DEBUGFS_ATTRIBUTE.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Pull networking updates from Jakub Kicinski:
 "Core:

   - support "prefer busy polling" NAPI operation mode, where we defer
     softirq for some time expecting applications to periodically busy
     poll

   - AF_XDP: improve efficiency by more batching and hindering the
     adjacency cache prefetcher

   - af_packet: make packet_fanout.arr size configurable up to 64K

   - tcp: optimize TCP zero copy receive in presence of partial or
     unaligned reads making zero copy a performance win for much smaller
     messages

   - XDP: add bulk APIs for returning / freeing frames

   - sched: support fragmenting IP packets as they come out of conntrack

   - net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs

  BPF:

   - BPF switch from crude rlimit-based to memcg-based memory accounting

   - BPF type format information for kernel modules and related tracing
     enhancements

   - BPF implement task local storage for BPF LSM

   - allow the FENTRY/FEXIT/RAW_TP tracing programs to use
     bpf_sk_storage

  Protocols:

   - mptcp: improve multiple xmit streams support, memory accounting and
     many smaller improvements

   - TLS: support CHACHA20-POLY1305 cipher

   - seg6: add support for SRv6 End.DT4/DT6 behavior

   - sctp: Implement RFC 6951: UDP Encapsulation of SCTP

   - ppp_generic: add ability to bridge channels directly

   - bridge: Connectivity Fault Management (CFM) support as is defined
     in IEEE 802.1Q section 12.14.

  Drivers:

   - mlx5: make use of the new auxiliary bus to organize the driver
     internals

   - mlx5: more accurate port TX timestamping support

   - mlxsw:
      - improve the efficiency of offloaded next hop updates by using
        the new nexthop object API
      - support blackhole nexthops
      - support IEEE 802.1ad (Q-in-Q) bridging

   - rtw88: major bluetooth co-existance improvements

   - iwlwifi: support new 6 GHz frequency band

   - ath11k: Fast Initial Link Setup (FILS)

   - mt7915: dual band concurrent (DBDC) support

   - net: ipa: add basic support for IPA v4.5

  Refactor:

   - a few pieces of in_interrupt() cleanup work from Sebastian Andrzej
     Siewior

   - phy: add support for shared interrupts; get rid of multiple driver
     APIs and have the drivers write a full IRQ handler, slight growth
     of driver code should be compensated by the simpler API which also
     allows shared IRQs

   - add common code for handling netdev per-cpu counters

   - move TX packet re-allocation from Ethernet switch tag drivers to a
     central place

   - improve efficiency and rename nla_strlcpy

   - number of W=1 warning cleanups as we now catch those in a patchwork
     build bot

  Old code removal:

   - wan: delete the DLCI / SDLA drivers

   - wimax: move to staging

   - wifi: remove old WDS wifi bridging support"

* tag 'net-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1922 commits)
  net: hns3: fix expression that is currently always true
  net: fix proc_fs init handling in af_packet and tls
  nfc: pn533: convert comma to semicolon
  af_vsock: Assign the vsock transport considering the vsock address flags
  af_vsock: Set VMADDR_FLAG_TO_HOST flag on the receive path
  vsock_addr: Check for supported flag values
  vm_sockets: Add VMADDR_FLAG_TO_HOST vsock flag
  vm_sockets: Add flags field in the vsock address data structure
  net: Disable NETIF_F_HW_TLS_TX when HW_CSUM is disabled
  tcp: Add logic to check for SYN w/ data in tcp_simple_retransmit
  net: mscc: ocelot: install MAC addresses in .ndo_set_rx_mode from process context
  nfc: s3fwrn5: Release the nfc firmware
  net: vxget: clean up sparse warnings
  mlxsw: spectrum_router: Use eXtended mezzanine to offload IPv4 router
  mlxsw: spectrum: Set KVH XLT cache mode for Spectrum2/3
  mlxsw: spectrum_router_xm: Introduce basic XM cache flushing
  mlxsw: reg: Add Router LPM Cache Enable Register
  mlxsw: reg: Add Router LPM Cache ML Delete Register
  mlxsw: spectrum_router_xm: Implement L-value tracking for M-index
  mlxsw: reg: Add XM Router M Table Register
  ...

Currently <crypto/sha.h> contains declarations for both SHA-1 and SHA-2,
and <crypto/sha3.h> contains declarations for SHA-3.

This organization is inconsistent, but more importantly SHA-1 is no
longer considered to be cryptographically secure.  So to the extent
possible, SHA-1 shouldn't be grouped together with any of the other SHA
versions, and usage of it should be phased out.

Therefore, split <crypto/sha.h> into two headers <crypto/sha1.h> and
<crypto/sha2.h>, and make everyone explicitly specify whether they want
the declarations for SHA-1, SHA-2, or both.

This avoids making the SHA-1 declarations visible to files that don't
want anything to do with SHA-1.  It also prepares for potentially moving
sha1.h into a new insecure/ or dangerous/ directory.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Wang Qing reports that IS_ERR_OR_NULL() should be matched with
PTR_ERR_OR_ZERO(), not PTR_ERR().

As it turns out, the error path always returns an error code,
i.e. NULL is never returned.
Update the code accordingly - s/IS_ERR_OR_NULL/IS_ERR.

Reported-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

At the time xts fallback tfm allocation fails the device struct
hasn't been enabled yet in the caam xts tfm's private context.

Fix this by using the device struct from xts algorithm's private context
or, when not available, by replacing dev_err with pr_err.

Fixes: 9d9b14dbe077 ("crypto: caam/jr - add fallback for XTS with more than 8B IV")
Fixes: 83e8aa912138 ("crypto: caam/qi - add fallback for XTS with more than 8B IV")
Fixes: 36e2d7cfdcf1 ("crypto: caam/qi2 - add fallback for XTS with more than 8B IV")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>