Pull Samsung clk driver fixes from Krzysztof Kozlowski:

 - Google GS101: Fix synchronous external abort during system suspend.
   The driver access registers not available for OS, although issue
   would not be visible in earlier kernels due to missing suspend
   support.

 - Tesla FSD: Correct PLL142XX lock time

* tag 'samsung-clk-fixes-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  clk: samsung: update PLL locktime for PLL142XX used on FSD platform
  clk: samsung: gs101: fix synchronous external abort in samsung_clk_save()

Currently PLL142XX locktime is 270. As per spec, it should be 150. Hence
update PLL142XX controller locktime to 150.

Cc: stable@vger.kernel.org
Fixes: 4f346005aaed ("clk: samsung: fsd: Add initial clock support")
Signed-off-by: Varada Pavani <v.pavani@samsung.com>
Link: https://lore.kernel.org/r/20250225131918.50925-3-v.pavani@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

EARLY_WAKEUP_SW_TRIG_*_SET and EARLY_WAKEUP_SW_TRIG_*_CLEAR
registers are only writeable. Attempting to read these registers
during samsung_clk_save() causes a synchronous external abort.

Remove these 8 registers from cmu_top_clk_regs[] array so that
system suspend gets further.

Note: the code path can be exercised using the following command:
echo mem > /sys/power/state

Fixes: 2c597bb7d66a ("clk: samsung: clk-gs101: Add cmu_top, cmu_misc and cmu_apm support")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250303-clk-suspend-fix-v1-1-c2edaf66260f@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

The parent of disp_cc_mdss_byte0_intf_clk clock should not propagate up
the rates, because this messes up entire clock hierarchy when setting
clock rates in MSM DSI driver.

The dsi_link_clk_set_rate_6g() first sets entire clock hierarchy rates
via dev_pm_opp_set_rate() on byte clock and then sets individual clock
rates, like pixel and byte_intf clocks, to proper frequencies.  Having
CLK_SET_RATE_PARENT caused that entire tree was re-calced and the byte
clock received halved frequency.  Drop CLK_SET_RATE_PARENT to fix this
and align with SM8550 and SM8650.

Fixes: f1080d8dab0f ("clk: qcom: dispcc-sm8750: Add SM8750 Display clock controller")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250129154519.209791-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Pull MM updates from Andrew Morton:
 "The various patchsets are summarized below. Plus of course many
  indivudual patches which are described in their changelogs.

   - "Allocate and free frozen pages" from Matthew Wilcox reorganizes
     the page allocator so we end up with the ability to allocate and
     free zero-refcount pages. So that callers (ie, slab) can avoid a
     refcount inc & dec

   - "Support large folios for tmpfs" from Baolin Wang teaches tmpfs to
     use large folios other than PMD-sized ones

   - "Fix mm/rodata_test" from Petr Tesarik performs some maintenance
     and fixes for this small built-in kernel selftest

   - "mas_anode_descend() related cleanup" from Wei Yang tidies up part
     of the mapletree code

   - "mm: fix format issues and param types" from Keren Sun implements a
     few minor code cleanups

   - "simplify split calculation" from Wei Yang provides a few fixes and
     a test for the mapletree code

   - "mm/vma: make more mmap logic userland testable" from Lorenzo
     Stoakes continues the work of moving vma-related code into the
     (relatively) new mm/vma.c

   - "mm/page_alloc: gfp flags cleanups for alloc_contig_*()" from David
     Hildenbrand cleans up and rationalizes handling of gfp flags in the
     page allocator

   - "readahead: Reintroduce fix for improper RA window sizing" from Jan
     Kara is a second attempt at fixing a readahead window sizing issue.
     It should reduce the amount of unnecessary reading

   - "synchronously scan and reclaim empty user PTE pages" from Qi Zheng
     addresses an issue where "huge" amounts of pte pagetables are
     accumulated:

       https://lore.kernel.org/lkml/cover.1718267194.git.zhengqi.arch@bytedance.com/

     Qi's series addresses this windup by synchronously freeing PTE
     memory within the context of madvise(MADV_DONTNEED)

   - "selftest/mm: Remove warnings found by adding compiler flags" from
     Muhammad Usama Anjum fixes some build warnings in the selftests
     code when optional compiler warnings are enabled

   - "mm: don't use __GFP_HARDWALL when migrating remote pages" from
     David Hildenbrand tightens the allocator's observance of
     __GFP_HARDWALL

   - "pkeys kselftests improvements" from Kevin Brodsky implements
     various fixes and cleanups in the MM selftests code, mainly
     pertaining to the pkeys tests

   - "mm/damon: add sample modules" from SeongJae Park enhances DAMON to
     estimate application working set size

   - "memcg/hugetlb: Rework memcg hugetlb charging" from Joshua Hahn
     provides some cleanups to memcg's hugetlb charging logic

   - "mm/swap_cgroup: remove global swap cgroup lock" from Kairui Song
     removes the global swap cgroup lock. A speedup of 10% for a
     tmpfs-based kernel build was demonstrated

   - "zram: split page type read/write handling" from Sergey Senozhatsky
     has several fixes and cleaups for zram in the area of
     zram_write_page(). A watchdog softlockup warning was eliminated

   - "move pagetable_*_dtor() to __tlb_remove_table()" from Kevin
     Brodsky cleans up the pagetable destructor implementations. A rare
     use-after-free race is fixed

   - "mm/debug: introduce and use VM_WARN_ON_VMG()" from Lorenzo Stoakes
     simplifies and cleans up the debugging code in the VMA merging
     logic

   - "Account page tables at all levels" from Kevin Brodsky cleans up
     and regularizes the pagetable ctor/dtor handling. This results in
     improvements in accounting accuracy

   - "mm/damon: replace most damon_callback usages in sysfs with new
     core functions" from SeongJae Park cleans up and generalizes
     DAMON's sysfs file interface logic

   - "mm/damon: enable page level properties based monitoring" from
     SeongJae Park increases the amount of information which is
     presented in response to DAMOS actions

   - "mm/damon: remove DAMON debugfs interface" from SeongJae Park
     removes DAMON's long-deprecated debugfs interfaces. Thus the
     migration to sysfs is completed

   - "mm/hugetlb: Refactor hugetlb allocation resv accounting" from
     Peter Xu cleans up and generalizes the hugetlb reservation
     accounting

   - "mm: alloc_pages_bulk: small API refactor" from Luiz Capitulino
     removes a never-used feature of the alloc_pages_bulk() interface

   - "mm/damon: extend DAMOS filters for inclusion" from SeongJae Park
     extends DAMOS filters to support not only exclusion (rejecting),
     but also inclusion (allowing) behavior

   - "Add zpdesc memory descriptor for zswap.zpool" from Alex Shi
     introduces a new memory descriptor for zswap.zpool that currently
     overlaps with struct page for now. This is part of the effort to
     reduce the size of struct page and to enable dynamic allocation of
     memory descriptors

   - "mm, swap: rework of swap allocator locks" from Kairui Song redoes
     and simplifies the swap allocator locking. A speedup of 400% was
     demonstrated for one workload. As was a 35% reduction for kernel
     build time with swap-on-zram

   - "mm: update mips to use do_mmap(), make mmap_region() internal"
     from Lorenzo Stoakes reworks MIPS's use of mmap_region() so that
     mmap_region() can be made MM-internal

   - "mm/mglru: performance optimizations" from Yu Zhao fixes a few
     MGLRU regressions and otherwise improves MGLRU performance

   - "Docs/mm/damon: add tuning guide and misc updates" from SeongJae
     Park updates DAMON documentation

   - "Cleanup for memfd_create()" from Isaac Manjarres does that thing

   - "mm: hugetlb+THP folio and migration cleanups" from David
     Hildenbrand provides various cleanups in the areas of hugetlb
     folios, THP folios and migration

   - "Uncached buffered IO" from Jens Axboe implements the new
     RWF_DONTCACHE flag which provides synchronous dropbehind for
     pagecache reading and writing. To permite userspace to address
     issues with massive buildup of useless pagecache when
     reading/writing fast devices

   - "selftests/mm: virtual_address_range: Reduce memory" from Thomas
     Weißschuh fixes and optimizes some of the MM selftests"

* tag 'mm-stable-2025-01-26-14-59' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (321 commits)
  mm/compaction: fix UBSAN shift-out-of-bounds warning
  s390/mm: add missing ctor/dtor on page table upgrade
  kasan: sw_tags: use str_on_off() helper in kasan_init_sw_tags()
  tools: add VM_WARN_ON_VMG definition
  mm/damon/core: use str_high_low() helper in damos_wmark_wait_us()
  seqlock: add missing parameter documentation for raw_seqcount_try_begin()
  mm/page-writeback: consolidate wb_thresh bumping logic into __wb_calc_thresh
  mm/page_alloc: remove the incorrect and misleading comment
  zram: remove zcomp_stream_put() from write_incompressible_page()
  mm: separate move/undo parts from migrate_pages_batch()
  mm/kfence: use str_write_read() helper in get_access_type()
  selftests/mm/mkdirty: fix memory leak in test_uffdio_copy()
  kasan: hw_tags: Use str_on_off() helper in kasan_init_hw_tags()
  selftests/mm: virtual_address_range: avoid reading from VM_IO mappings
  selftests/mm: vm_util: split up /proc/self/smaps parsing
  selftests/mm: virtual_address_range: unmap chunks after validation
  selftests/mm: virtual_address_range: mmap() without PROT_WRITE
  selftests/memfd/memfd_test: fix possible NULL pointer dereference
  mm: add FGP_DONTCACHE folio creation flag
  mm: call filemap_fdatawrite_range_kick() after IOCB_DONTCACHE issue
  ...

Before SLUB initialization, various subsystems used memblock_alloc to
allocate memory.  In most cases, when memory allocation fails, an
immediate panic is required.  To simplify this behavior and reduce
repetitive checks, introduce `memblock_alloc_or_panic`.  This function
ensures that memory allocation failures result in a panic automatically,
improving code readability and consistency across subsystems that require
this behavior.

[guoweikang.kernel@gmail.com: arch/s390: save_area_alloc default failure behavior changed to panic]
  Link: https://lkml.kernel.org/r/20250109033136.2845676-1-guoweikang.kernel@gmail.com
  Link: https://lore.kernel.org/lkml/Z2fknmnNtiZbCc7x@kernel.org/
Link: https://lkml.kernel.org/r/20250102072528.650926-1-guoweikang.kernel@gmail.com
Signed-off-by: Guo Weikang <guoweikang.kernel@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>	[m68k]
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>	[s390]
Acked-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Pull pci updates from Bjorn Helgaas:
 "Enumeration:

   - Batch sizing of multiple BARs while memory decoding is disabled
     instead of disabling/enabling decoding for each BAR individually;
     this optimizes virtualized environments where toggling decoding
     enable is expensive (Alex Williamson)

   - Add host bridge .enable_device() and .disable_device() hooks for
     bridges that need to configure things like Requester ID to StreamID
     mapping when enabling devices (Frank Li)

   - Extend struct pci_ecam_ops with .enable_device() and
     .disable_device() hooks so drivers that use pci_host_common_probe()
     instead of their own .probe() have a way to set the
     .enable_device() callbacks (Marc Zyngier)

   - Drop 'No bus range found' message so we don't complain when DTs
     don't specify the default 'bus-range = <0x00 0xff>' (Bjorn Helgaas)

   - Rename the drivers/pci/of_property.c struct of_pci_range to
     of_pci_range_entry to avoid confusion with the global of_pci_range
     in include/linux/of_address.h (Bjorn Helgaas)

  Driver binding:

   - Update resource request API documentation to encourage callers to
     supply a driver name when requesting resources (Philipp Stanner)

   - Export pci_intx_unmanaged() and pcim_intx() (always managed) so
     callers of pci_intx() (which is sometimes managed) can explicitly
     choose the one they need (Philipp Stanner)

   - Convert drivers from pci_intx() to always-managed pcim_intx() or
     never-managed pci_intx_unmanaged(): amd_sfh, ata (ahci, ata_piix,
     pata_rdc, sata_sil24, sata_sis, sata_uli, sata_vsc), bnx2x, bna,
     ntb, qtnfmac, rtsx, tifm_7xx1, vfio, xen-pciback (Philipp Stanner)

   - Remove pci_intx_unmanaged() since pci_intx() is now always
     unmanaged and pcim_intx() is always managed (Philipp Stanner)

  Error handling:

   - Unexport pcie_read_tlp_log() to encourage drivers to use PCI core
     logging rather than building their own (Ilpo Järvinen)

   - Move TLP Log handling to its own file (Ilpo Järvinen)

   - Store number of supported End-End TLP Prefixes always so we can
     read the correct number of DWORDs from the TLP Prefix Log (Ilpo
     Järvinen)

   - Read TLP Prefixes in addition to the Header Log in
     pcie_read_tlp_log() (Ilpo Järvinen)

   - Add pcie_print_tlp_log() to consolidate printing of TLP Header and
     Prefix Log (Ilpo Järvinen)

   - Quirk the Intel Raptor Lake-P PIO log size to accommodate vendor
     BIOSes that don't configure it correctly (Takashi Iwai)

  ASPM:

   - Save parent L1 PM Substates config so when we restore it along with
     an endpoint's config, the parent info isn't junk (Jian-Hong Pan)

  Power management:

   - Avoid D3 for Root Ports on TUXEDO Sirius Gen1 with old BIOS because
     the system can't wake up from suspend (Werner Sembach)

  Endpoint framework:

   - Destroy the EPC device in devm_pci_epc_destroy(), which previously
     didn't call devres_release() (Zijun Hu)

   - Finish virtual EP removal in pci_epf_remove_vepf(), which
     previously caused a subsequent pci_epf_add_vepf() to fail with
     -EBUSY (Zijun Hu)

   - Write BAR_MASK before iATU registers in pci_epc_set_bar() so we
     don't depend on the BAR_MASK reset value being larger than the
     requested BAR size (Niklas Cassel)

   - Prevent changing BAR size/flags in pci_epc_set_bar() to prevent
     reads from bypassing the iATU if we reduced the BAR size (Niklas
     Cassel)

   - Verify address alignment when programming iATU so we don't attempt
     to write bits that are read-only because of the BAR size, which
     could lead to directing accesses to the wrong address (Niklas
     Cassel)

   - Implement artpec6 pci_epc_features so we can rely on all drivers
     supporting it so we can use it in EPC core code (Niklas Cassel)

   - Check for BARs of fixed size to prevent endpoint drivers from
     trying to change their size (Niklas Cassel)

   - Verify that requested BAR size is a power of two when endpoint
     driver sets the BAR (Niklas Cassel)

  Endpoint framework tests:

   - Clear pci-epf-test dma_chan_rx, not dma_chan_tx, after freeing
     dma_chan_rx (Mohamed Khalfella)

   - Correct the DMA MEMCPY test so it doesn't fail if the Endpoint
     supports both DMA_PRIVATE and DMA_MEMCPY (Manivannan Sadhasivam)

   - Add pci-epf-test and pci_endpoint_test support for capabilities
     (Niklas Cassel)

   - Add Endpoint test for consecutive BARs (Niklas Cassel)

   - Remove redundant comparison from Endpoint BAR test because a > 1MB
     BAR can always be exactly covered by iterating with a 1MB buffer
     (Hans Zhang)

   - Move and convert PCI Endpoint tests from tools/pci to Kselftests
     (Manivannan Sadhasivam)

  Apple PCIe controller driver:

   - Convert StreamID mapping configuration from a bus notifier to the
     .enable_device() and .disable_device() callbacks (Marc Zyngier)

  Freescale i.MX6 PCIe controller driver:

   - Add Requester ID to StreamID mapping configuration when enabling
     devices (Frank Li)

   - Use DWC core suspend/resume functions for imx6 (Frank Li)

   - Add suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
     Zhu)

   - Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
     i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank
     Li)

   - Add DT binding for optional i.MX95 Refclk and driver support to
     enable it if the platform hasn't enabled it (Richard Zhu)

   - Configure PHY based on controller being in Root Complex or Endpoint
     mode (Frank Li)

   - Rely on dbi2 and iATU base addresses from DT via
     dw_pcie_get_resources() instead of hardcoding them (Richard Zhu)

   - Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
     asserted in imx_pcie_assert_core_reset() (Richard Zhu)

   - Add missing reference clock enable or disable logic for IMX6SX,
     IMX7D, IMX8MM (Richard Zhu)

   - Remove redundant imx7d_pcie_init_phy() since
     imx7d_pcie_enable_ref_clk() does the same thing (Richard Zhu)

  Freescale Layerscape PCIe controller driver:

   - Simplify by using syscon_regmap_lookup_by_phandle_args() instead
     of syscon_regmap_lookup_by_phandle() followed by
     of_property_read_u32_array() (Krzysztof Kozlowski)

  Marvell MVEBU PCIe controller driver:

   - Add MODULE_DEVICE_TABLE() to enable module autoloading (Liao Chen)

  MediaTek PCIe Gen3 controller driver:

   - Use clk_bulk_prepare_enable() instead of separate
     clk_bulk_prepare() and clk_bulk_enable() (Lorenzo Bianconi)

   - Rearrange reset assert/deassert so they're both done in the
     *_power_up() callbacks (Lorenzo Bianconi)

   - Document that Airoha EN7581 requires PHY init and power-on before
     PHY reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo
     Bianconi)

   - Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
     method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)

   - Sleep instead of delay during Airoha EN7581 power-up, since this is
     a non-atomic context (Lorenzo Bianconi)

   - Skip PERST# assertion on Airoha EN7581 during probe and
     suspend/resume to avoid a hardware defect (Lorenzo Bianconi)

   - Enable async probe to reduce system startup time (Douglas Anderson)

  Microchip PolarFlare PCIe controller driver:

   - Set up the inbound address translation based on whether the
     platform allows coherent or non-coherent DMA (Daire McNamara)

   - Update DT binding such that platforms are DMA-coherent by default
     and must specify 'dma-noncoherent' if needed (Conor Dooley)

  Mobiveil PCIe controller driver:

   - Convert mobiveil-pcie.txt to YAML and update 'interrupt-names'
     and 'reg-names' (Frank Li)

  Qualcomm PCIe controller driver:

   - Add DT SM8550 and SM8650 optional 'global' interrupt for link
     events (Neil Armstrong)

   - Add DT 'compatible' strings for IPQ5424 PCIe controller (Manikanta
     Mylavarapu)

   - If 'global' IRQ is supported for detection of Link Up events, tell
     DWC core not to wait for link up (Krishna chaitanya chundru)

  Renesas R-Car PCIe controller driver:

   - Avoid passing stack buffer as resource name (King Dix)

  Rockchip PCIe controller driver:

   - Simplify clock and reset handling by using bulk interfaces (Anand
     Moon)

   - Pass typed rockchip_pcie (not void) pointer to
     rockchip_pcie_disable_clocks() (Anand Moon)

   - Return -ENOMEM, not success, when pci_epc_mem_alloc_addr() fails
     (Dan Carpenter)

  Rockchip DesignWare PCIe controller driver:

   - Use dll_link_up IRQ to detect Link Up and enumerate devices so
     users don't have to manually rescan (Niklas Cassel)

   - Tell DWC core not to wait for link up since the 'sys' interrupt is
     required and detects Link Up events (Niklas Cassel)

  Synopsys DesignWare PCIe controller driver:

   - Don't wait for link up in DWC core if driver can detect Link Up
     event (Krishna chaitanya chundru)

   - Update ICC and OPP votes after Link Up events (Krishna chaitanya
     chundru)

   - Always stop link in dw_pcie_suspend_noirq(), which is required at
     least for i.MX8QM to re-establish link on resume (Richard Zhu)

   - Drop racy and unnecessary LTSSM state check before sending
     PME_TURN_OFF message in dw_pcie_suspend_noirq() (Richard Zhu)

   - Add struct of_pci_range.parent_bus_addr for devices that need their
     immediate parent bus address, not the CPU address, e.g., to program
     an internal Address Translation Unit (iATU) (Frank Li)

  TI DRA7xx PCIe controller driver:

   - Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
     syscon_regmap_lookup_by_phandle() followed by
     of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
     (Krzysztof Kozlowski)

  Xilinx Versal CPM PCIe controller driver:

   - Add DT binding and driver support for Xilinx Versal CPM5
     (Thippeswamy Havalige)

  MicroSemi Switchtec management driver:

   - Add Microchip PCI100X device IDs (Rakesh Babu Saladi)

  Miscellaneous:

   - Move reset related sysfs code from pci.c to pci-sysfs.c where other
     similar code lives (Ilpo Järvinen)

   - Simplify reset_method_store() memory management by using __free()
     instead of explicit kfree() cleanup (Ilpo Järvinen)

   - Constify struct bin_attribute for sysfs, VPD, P2PDMA, and the IBM
     ACPI hotplug driver (Thomas Weißschuh)

   - Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT (Dongdong
     Zhang)

   - Correct documentation of the 'config_acs=' kernel parameter
     (Akihiko Odaki)"

* tag 'pci-v6.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (111 commits)
  PCI: Batch BAR sizing operations
  dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
  PCI: microchip: Set inbound address translation for coherent or non-coherent mode
  Documentation: Fix pci=config_acs= example
  PCI: Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT
  PCI: Don't include 'pm_wakeup.h' directly
  selftests: pci_endpoint: Migrate to Kselftest framework
  selftests: Move PCI Endpoint tests from tools/pci to Kselftests
  misc: pci_endpoint_test: Fix IOCTL return value
  dt-bindings: PCI: qcom: Document the IPQ5424 PCIe controller
  dt-bindings: PCI: qcom,pcie-sm8550: Document 'global' interrupt
  dt-bindings: PCI: mobiveil: Convert mobiveil-pcie.txt to YAML
  PCI: switchtec: Add Microchip PCI100X device IDs
  misc: pci_endpoint_test: Remove redundant 'remainder' test
  misc: pci_endpoint_test: Add consecutive BAR test
  misc: pci_endpoint_test: Add support for capabilities
  PCI: endpoint: pci-epf-test: Add support for capabilities
  PCI: endpoint: pci-epf-test: Fix check for DMA MEMCPY test
  PCI: endpoint: pci-epf-test: Set dma_chan_rx pointer to NULL on error
  PCI: dwc: Simplify config resource lookup
  ...

Pull clk updates from Stephen Boyd:
 "A pretty quiet cycle this time around. We have a bunch of new Qualcomm
  clk drivers, per usual, and then a handful of drivers for other SoCs.
  Then the usual pile of cleanups is fairly small data fixes or
  converting DT bindings to YAML so they can be validated.

  No changes to the core framework besides an OF node refcount bump that
  never got decremented.

  New Drivers:

   - 5L35023 variant of Versa 3 clock generator

   - Various Qualcomm clk controllers: IPQ CMN PLL, SM6115 LPASS, SM750
     global, tcsr, rpmh, and display. X Plus GPU and global. QCS615 rpmh
     and MSM8937 and MSM8940 RPM.

   - Qualcomm Pongo and Taycan Alpha PLLs

   - Qualcomm IPQ5424 NoC-related interconnect clks

   - Renesas RZ/G3E (R9A09G047) SoC clk driver

   - SAMA7D65 SoC clk driver

   - Samsung Exynos990 SoC clk driver"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (159 commits)
  clk: analogbits: Fix incorrect calculation of vco rate delta
  clk: bcm: rpi: Add disp clock
  clk: bcm: rpi: Create helper to retrieve private data
  clk: bcm: rpi: Enable minimize for all firmware clocks
  clk: bcm: rpi: Allow cpufreq driver to also adjust gpu clocks
  clk: bcm: rpi: Add ISP to exported clocks
  clk: stm32f4: support spread spectrum clock generation
  clk: stm32f4: use FIELD helpers to access the PLLCFGR fields
  dt-bindings: clock: st,stm32-rcc: support spread spectrum clocking
  dt-bindings: clock: convert stm32 rcc bindings to json-schema
  clk: Use str_enable_disable-like helpers
  clk: clk-loongson2: Fix the number count of clk provider
  clk: clk-loongson2: Switch to use devm_clk_hw_register_fixed_rate_parent_data()
  clk: starfive: Make _clk_get become a common helper function
  clk: en7523: Add clock for eMMC for EN7581
  dt-bindings: clock: add ID for eMMC for EN7581
  dt-bindings: clock: drop NUM_CLOCKS define for EN7581
  clk: en7523: Rework clock handling for different clock numbers
  clk: thead: Fix cpu2vp_clk for TH1520 AP_SUBSYS clocks
  clk: thead: Add CLK_IGNORE_UNUSED to fix TH1520 boot
  ...

* clk-fixes:
  clk: clk-loongson2: Fix the number count of clk provider
  clk: mmp2: call pm_genpd_init() only after genpd.name is set
  clk: sunxi-ng: a100: enable MMC clock reparenting
  clk: clk-imx8mp-audiomix: fix function signature
  clk: thead: Fix TH1520 emmc and shdci clock rate

* clk-airoha:
  clk: en7523: Add clock for eMMC for EN7581
  dt-bindings: clock: add ID for eMMC for EN7581
  dt-bindings: clock: drop NUM_CLOCKS define for EN7581
  clk: en7523: Rework clock handling for different clock numbers
  clk: en7523: Initialize num before accessing hws in en7523_register_clocks()
  clk: en7523: Fix wrong BUS clock for EN7581
  clk: amlogic: axg-audio: revert reset implementation
  Revert "clk: Fix invalid execution of clk_set_rate"

* clk-rockchip:
  clk: rockchip: rk3588: make refclko25m_ethX critical
  clk: rockchip: rk3588: drop RK3588_LINKED_CLK
  clk: rockchip: implement linked gate clock support
  clk: rockchip: expose rockchip_clk_set_lookup
  clk: rockchip: rk3588: register GATE_LINK later
  clk: rockchip: support clocks registered late

* clk-stm:
  clk: stm32f4: support spread spectrum clock generation
  clk: stm32f4: use FIELD helpers to access the PLLCFGR fields
  dt-bindings: clock: st,stm32-rcc: support spread spectrum clocking
  dt-bindings: clock: convert stm32 rcc bindings to json-schema

* clk-thead:
  clk: thead: Fix cpu2vp_clk for TH1520 AP_SUBSYS clocks
  clk: thead: Add CLK_IGNORE_UNUSED to fix TH1520 boot
  clk: thead: Fix clk gate registration to pass flags

* clk-bcm:
  clk: bcm: rpi: Add disp clock
  clk: bcm: rpi: Create helper to retrieve private data
  clk: bcm: rpi: Enable minimize for all firmware clocks
  clk: bcm: rpi: Allow cpufreq driver to also adjust gpu clocks
  clk: bcm: rpi: Add ISP to exported clocks