clk: tegra: Changes for v4.2-rc1

This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.

Conflicts:
	drivers/clk/Kconfig

This driver supports the TI CDCE925 programmable clock synthesizer.
The chip contains two PLLs with spread-spectrum clocking support and
five output dividers. The driver only supports the following setup,
and uses a fixed setting for the output muxes:
  Y1 is derived from the input clock
  Y2 and Y3 derive from PLL1
  Y4 and Y5 derive from PLL2
Given a target output frequency, the driver will set the PLL and
divider to best approximate the desired output.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Add clock drivers for hi6220 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.

We add one divider clock for hi6220 because the divider in hi6220
also has a mask bit but it doesnot obey the rule defined by flag
"CLK_DIVIDER_HIWORD_MASK", we can not get index of the mask bit by
left shift fixed bits (e.g. 16 bits), so we add this divider clock
to handle it.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Having this Kconfig sourced outside the clk menu means the option
is under the "Device Drivers" menu instead of the "Common Clock
Framework" menu. Move it so that the bcm clock config options are
in the right place.

Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The EMC clock driver uses symbols exported by the EMC driver, so it
needs the corresponding dependency to avoid build breakage.

Signed-off-by: Thierry Reding <treding@nvidia.com>

Some board designers, when running out of clock output pads, decide to
(mis)use PWM output pads to provide a clock to external components.
This driver supports this practice by providing an adapter between the
PWM and clock bindings in the device tree. As the PWM bindings specify
the period in the device tree, this is a fixed clock.

Tested-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Pull clock framework updates from Mike Turquette:
 "The clock framework changes contain the usual driver additions,
  enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
  devices.

  Additionally the framework core underwent a bit of surgery with two
  major changes:

   - The boundary between the clock core and clock providers (e.g clock
     drivers) is now more well defined with dedicated provider helper
     functions.  struct clk no longer maps 1:1 with the hardware clock
     but is a true per-user cookie which helps us tracker users of
     hardware clocks and debug bad behavior.

   - The addition of rate constraints for clocks.  Rate ranges are now
     supported which are analogous to the voltage ranges in the
     regulator framework.

  Unfortunately these changes to the core created some breakeage.  We
  think we fixed it all up but for this reason there are lots of last
  minute commits trying to undo the damage"

* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
  clk: Only recalculate the rate if needed
  Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
  clk: qoriq: Add support for the platform PLL
  powerpc/corenet: Enable CLK_QORIQ
  clk: Replace explicit clk assignment with __clk_hw_set_clk
  clk: Add __clk_hw_set_clk helper function
  clk: Don't dereference parent clock if is NULL
  MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
  clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
  clk: shmobile: div6: Avoid division by zero in .round_rate()
  clk: mxs: Fix invalid 32-bit access to frac registers
  clk: omap: compile legacy omap3 clocks conditionally
  clkdev: Export clk_register_clkdev
  clk: Add rate constraints to clocks
  clk: remove clk-private.h
  pci: xgene: do not use clk-private.h
  arm: omap2+ remove dead clock code
  clk: Make clk API return per-user struct clk instances
  clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
  clk: tegra: Add support for the Tegra132 CAR IP block
  ...

Freescale introduced new ARM-based socs which using the compatible
clock IP block with PowerPC-based socs'. So this driver can be used
on both platforms.
Updated relevant descriptions and renamed this driver to better
represent its meaning and keep the function of driver untouched.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

The driver allows using CDCE706 in its default configuration recorded in
EEPROM and adjusting of synthesized clocks by consumers.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>