commit b928466b2169e061822daad48ecf55b005445547 upstream.

The code setting XP watchpoint comparator and mask registers should, in
order to be fully compliant with specification, zero one or more most
significant bits of each field. In both L cases it means zeroing bit 63.
The bitmask doing this was wrong, though, zeroing bit 60 instead.
Fortunately, due to a lucky coincidence, this turned out to be fairly
innocent with the existing hardware.

Fixed now.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b7c1beb278e8e3dc664ed3df3fc786db126120a9 upstream.

Fuzzing the CCN perf driver revealed a small but definitely dangerous
mistake in the event setup code. When a cycle counter is requested, the
driver should not reconfigure the events bus at all, otherwise it will
corrupt (in most but the simplest cases) its configuration and may end
up accessing XP array out of its bounds and corrupting control
registers.

Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4e486cba285ff06a1f28f0fc2991dde1482d1dcf upstream.

The "Miscellaneous Node" fell through cracks of node initialisation,
as its ID is shared with HN-I.

This patch treats MN as a special case (which it is), adding separate
validation check for it and pre-defining the node ID in relevant events
descriptions. That way one can simply run:

	# perf stat -a -e ccn/mn_ecbarrier/ <workload>

Additionally, direction in the MN pseudo-events XP watchpoint
definitions is corrected to be "TX" (1) as they are defined from the
crosspoint point of view (thus barriers are transmitted from XP to MN).

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for 4.7.  Here's the summary of
  the changes:

   - ATH79: Support for DTB passuing using the UHI boot protocol
   - ATH79: Remove support for builtin DTB.
   - ATH79: Add zboot debug serial support.
   - ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
            and DPT-Module.
   - ATH79: Update devicetree clock support for AR9132 and AR9331.
   - ATH79: Cleanup the DT code.
   - ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
   - ATH79: Fix regression in PCI window initialization.
   - BCM47xx: Move SPROM driver to drivers/firmware/
   - BCM63xx: Enable partition parser in defconfig.
   - BMIPS: BMIPS5000 has I cache filing from D cache
   - BMIPS: BMIPS: Add cpu-feature-overrides.h
   - BMIPS: Add Whirlwind support
   - BMIPS: Adjust mips-hpt-frequency for BCM7435
   - BMIPS: Remove maxcpus from BCM97435SVMB DTS
   - BMIPS: Add missing 7038 L1 register cells to BCM7435
   - BMIPS: Various tweaks to initialization code.
   - BMIPS: Enable partition parser in defconfig.
   - BMIPS: Cache tweaks.
   - BMIPS: Add UART, I2C and SATA devices to DT.
   - BMIPS: Add BCM6358 and BCM63268support
   - BMIPS: Add device tree example for BCM6358.
   - BMIPS: Improve Improve BCM6328 and BCM6368 device trees
   - Lantiq: Add support for device tree file from boot loader
   - Lantiq: Allow build with no built-in DT.
   - Loongson 3: Reserve 32MB for RS780E integrated GPU.
   - Loongson 3: Fix build error after ld-version.sh modification
   - Loongson 3: Move chipset ACPI code from drivers to arch.
   - Loongson 3: Speedup irq processing.
   - Loongson 3: Add basic Loongson 3A support.
   - Loongson 3: Set cache flush handlers to nop.
   - Loongson 3: Invalidate special TLBs when needed.
   - Loongson 3: Fast TLB refill handler.
   - MT7620: Fallback strategy for invalid syscfg0.
   - Netlogic: Fix CP0_EBASE redefinition warnings
   - Octeon: Initialization fixes
   - Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
   - Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
   - Octeon: Correctly handle endian-swapped initramfs images.
   - Octeon: Support CN73xx, CN75xx and CN78xx.
   - Octeon: Remove dead code from cvmx-sysinfo.
   - Octeon: Extend number of supported CPUs past 32.
   - Octeon: Remove some code limiting NR_IRQS to 255.
   - Octeon: Simplify octeon_irq_ciu_gpio_set_type.
   - Octeon: Mark some functions __init in smp.c
   - Octeon: Octeon: Add Octeon III CN7xxx interface detection
   - PIC32: Add serial driver and bindings for it.
   - PIC32: Add PIC32 deadman timer driver and bindings.
   - PIC32: Add PIC32 clock timer driver and bindings.
   - Pistachio: Determine SoC revision during boot
   - Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
   - Sibyte: Strip redundant comments from bcm1480_regs.h.
   - Panic immediately if panic_on_oops is set.
   - module: fix incorrect IS_ERR_VALUE macro usage.
   - module: Make consistent use of pr_*
   - Remove no longer needed work_on_cpu() call.
   - Remove CONFIG_IPV6_PRIVACY from defconfigs.
   - Fix registers of non-crashing CPUs in dumps.
   - Handle MIPSisms in new vmcore_elf32_check_arch.
   - Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
   - Allow RIXI to be used on non-R2 or R6 cores.
   - Reserve nosave data for hibernation
   - Fix siginfo.h to use strict POSIX types.
   - Don't unwind user mode with EVA.
   - Fix watchpoint restoration
   - Ptrace watchpoints for R6.
   - Sync icache when it fills from dcache
   - I6400 I-cache fills from dcache.
   - Various MSA fixes.
   - Cleanup MIPS_CPU_* definitions.
   - Signal: Move generic copy_siginfo to signal.h
   - Signal: Fix uapi include in exported asm/siginfo.h
   - Timer fixes for sake of KVM.
   - XPA TLB refill fixes.
   - Treat perf counter feature
   - Update John Crispin's email address
   - Add PIC32 watchdog and bindings.
   - Handle R10000 LL/SC bug in set_pte()
   - cpufreq: Various fixes for Longson1.
   - R6: Fix R2 emulation.
   - mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
   - ELF: ABI and FP fixes.
   - Allow for relocatable kernel and use that to support KASLR.
   - Fix CPC_BASE_ADDR mask
   - Plenty fo smp-cps, CM, R6 and M6250 fixes.
   - Make reset_control_ops const.
   - Fix kernel command line handling of leading whitespace.
   - Cleanups to cache handling.
   - Add brcm, bcm6345-l1-intc device tree bindings.
   - Use generic clkdev.h header
   - Remove CLK_IS_ROOT usage.
   - Misc small cleanups.
   - CM: Fix compilation error when !MIPS_CM
   - oprofile: Fix a preemption issue
   - Detect DSP ASE v3 support:1"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
  MIPS: pic32mzda: fix getting timer clock rate.
  MIPS: ath79: fix regression in PCI window initialization
  MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
  MIPS: Fix VZ probe gas errors with binutils <2.24
  MIPS: perf: Fix I6400 event numbers
  MIPS: DEC: Export `ioasic_ssr_lock' to modules
  MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
  MIPS: CM: Fix compilation error when !MIPS_CM
  MIPS: Fix genvdso error on rebuild
  USB: ohci-jz4740: Remove obsolete driver
  MIPS: JZ4740: Probe OHCI platform device via DT
  MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
  MIPS: pistachio: Determine SoC revision during boot
  MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
  mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
  MIPS: Prevent "restoration" of MSA context in non-MSA kernels
  MIPS: cevt-r4k: Dynamically calculate min_delta_ns
  MIPS: malta-time: Take seconds into account
  MIPS: malta-time: Start GIC count before syncing to RTC
  MIPS: Force CPUs to lose FP context during mode switches
  ...

Pull ARM SoC driver updates from Arnd Bergmann:
 "Driver updates for ARM SoCs, these contain various things that touch
  the drivers/ directory but got merged through arm-soc for practical
  reasons.

  For the most part, this is now related to power management
  controllers, which have not yet been abstracted into a separate
  subsystem, and typically require some code in drivers/soc or arch/arm
  to control the power domains.

  Another large chunk here is a rework of the NVIDIA Tegra USB3.0
  support, which was surprisingly tricky and took a long time to get
  done.

  Finally, reset controller handling as always gets merged through here
  as well"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
  arm-ccn: Enable building as module
  soc/tegra: pmc: Add generic PM domain support
  usb: xhci: tegra: Add Tegra210 support
  usb: xhci: Add NVIDIA Tegra XUSB controller driver
  dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
  dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
  PCI: tegra: Support per-lane PHYs
  dt-bindings: pci: tegra: Update for per-lane PHYs
  phy: tegra: Add Tegra210 support
  phy: Add Tegra XUSB pad controller support
  dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
  dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
  phy: core: Allow children node to be overridden
  clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
  drivers: firmware: psci: make two helper functions inline
  soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
  soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
  soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
  soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
  soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
  ...

Since commit 3b9d6da67e11 ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this
work_on_cpu() calls are no longer required.

Replace work_on_cpu() with a direct call of mips_cdmm_bus_up() or
mips_cdmm_bus_down(). Description of those functions are adapted.

Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: rt@linutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/13197/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS kernels allow platforms to invoke a custom Bus Error handler, add the
necessary code to do this for Broadcom SoCs where the GISB bus error handler can be used.

We may get a bus error from an address decoded outside of the GISB bus space,
so we need to check the validity of such a capture before printing anything.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: cernekee@gmail.com
Cc: arnd@arndb.de
Cc: jaedon.shin@gmail.com
Cc: pgynther@google.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12284/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arm-ccn driver uses irq_set_affinity, which is not exported and
hence cannot be built as a module, eventhough we have all the
bits ready. This patch makes use of the exported helper
irq_set_affinity_hint() instead. Also, the __free_irq expects
the affinity_hint to be NULL when we free the irq. So set the
affinity_hint to NULL at clean up.

Now that we can build it as a module, update the Kconfig to
reflect the change.

Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge "Broadcom ARM-based SoCs drivers changes" from Florian Fainelli:

- Justin adds a soc_dev driver to properly report to user-space the Broadcom
  STB SoC family, product and revision

- Florian reworks how the brcmstb_gisb driver dependency is done to enable it
  on Broadcom STB MIPS-based SoCs and remove a select in
  arch/arm/mach-bcm/Kconfig

* tag 'arm-soc/for-4.7/drivers' of http://github.com/Broadcom/stblinux:
  bus: brcmstb_gisb: Rework dependencies
  soc: brcmstb: add SoC driver to brcmstb

Do not have the machine Kconfig entry point need to select
BRCMSTB_GISB_ARB, instead, just let it be default ARCH_BRCMSTB which is
a better way to deal with this. While at it, also make it default
BMIPS_GENERIC so the legacy MIPS-based STB platforms can benefit from
the same thing.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>