linux-stable.git/drivers/bus, branch v4.14.2 Linux kernel stable tree License cleanup: add SPDX GPL-2.0 license identifier to files with no license 2017-11-02T10:10:55+00:00 Greg Kroah-Hartman gregkh@linuxfoundation.org 2017-11-01T14:07:57+00:00 b24413180f5600bcb3bb70fbed5cf186b60864bd Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bus: mbus: fix window size calculation for 4GB windows 2017-10-12T13:01:30+00:00 Jan Luebbe jlu@pengutronix.de 2017-08-28T15:25:16+00:00 2bbbd96357ce76cc45ec722c00f654aa7b189112 At least the Armada XP SoC supports 4GB on a single DRAM window. Because the size register values contain the actual size - 1, the MSB is set in that case. For example, the SDRAM window's control register's value is 0xffffffe1 for 4GB (bits 31 to 24 contain the size). The MBUS driver reads back each window's size from registers and calculates the actual size as (control_reg | ~DDR_SIZE_MASK) + 1, which overflows for 32 bit values, resulting in other miscalculations further on (a bad RAM window for the CESA crypto engine calculated by mvebu_mbus_setup_cpu_target_nooverlap() in my case). This patch changes the type in 'struct mbus_dram_window' from u32 to u64, which allows us to keep using the same register calculation code in most MBUS-using drivers (which calculate ->size - 1 again). Fixes: fddddb52a6c4 ("bus: introduce an Marvell EBU MBus driver") CC: stable@vger.kernel.org Signed-off-by: Jan Luebbe <jlu@pengutronix.de> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> 
At least the Armada XP SoC supports 4GB on a single DRAM window. Because
the size register values contain the actual size - 1, the MSB is set in
that case. For example, the SDRAM window's control register's value is
0xffffffe1 for 4GB (bits 31 to 24 contain the size).

The MBUS driver reads back each window's size from registers and
calculates the actual size as (control_reg | ~DDR_SIZE_MASK) + 1, which
overflows for 32 bit values, resulting in other miscalculations further
on (a bad RAM window for the CESA crypto engine calculated by
mvebu_mbus_setup_cpu_target_nooverlap() in my case).

This patch changes the type in 'struct mbus_dram_window' from u32 to
u64, which allows us to keep using the same register calculation code in
most MBUS-using drivers (which calculate ->size - 1 again).

Fixes: fddddb52a6c4 ("bus: introduce an Marvell EBU MBus driver")
CC: stable@vger.kernel.org
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc 2017-09-11T03:40:00+00:00 Linus Torvalds torvalds@linux-foundation.org 2017-09-11T03:40:00+00:00 ae46654bcff303b33facbbd04a3ad9c21d303f9b Pull ARM SoC driver updates from Olof Johansson: "This branch contains platform-related driver updates for ARM and ARM64. Among them: - Reset driver updates: + New API for dealing with arrays of resets + Make unimplemented {de,}assert return success on shared resets + MSDKv1 driver + Removal of obsolete Gemini reset driver + Misc updates for sunxi and Uniphier - SoC drivers: + Platform SoC driver registration on Tegra + Shuffle of Qualcomm drivers into a submenu + Allwinner A64 support for SRAM + Renesas R-Car R3 support + Power domains for Rockchip RK3366 - Misc updates and smaller fixes for TEE and memory driver subsystems" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits) firmware: arm_scpi: fix endianness of dev_id in struct dev_pstate_set soc/tegra: fuse: Add missing semi-colon soc/tegra: Restrict SoC device registration to Tegra drivers: soc: sunxi: add support for A64 and its SRAM C drivers: soc: sunxi: add support for remapping func value to reg value drivers: soc: sunxi: fix error processing on base address when claiming dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C bus: sunxi-rsb: Enable by default for ARM64 soc/tegra: Register SoC device firmware: tegra: set drvdata earlier memory: Convert to using %pOF instead of full_name soc: Convert to using %pOF instead of full_name bus: Convert to using %pOF instead of full_name firmware: Convert to using %pOF instead of full_name soc: mediatek: add SCPSYS power domain driver for MediaTek MT7622 SoC soc: mediatek: add header files required for MT7622 SCPSYS dt-binding soc: mediatek: reduce code duplication of scpsys_probe across all SoCs dt-bindings: soc: update the binding document for SCPSYS on MediaTek MT7622 SoC reset: uniphier: add analog amplifiers reset control reset: uniphier: add video input subsystem reset control ... 
Pull ARM SoC driver updates from Olof Johansson:
 "This branch contains platform-related driver updates for ARM and ARM64.

  Among them:

   - Reset driver updates:
     + New API for dealing with arrays of resets
     + Make unimplemented {de,}assert return success on shared resets
     + MSDKv1 driver
     + Removal of obsolete Gemini reset driver
     + Misc updates for sunxi and Uniphier

   - SoC drivers:
     + Platform SoC driver registration on Tegra
     + Shuffle of Qualcomm drivers into a submenu
     + Allwinner A64 support for SRAM
     + Renesas R-Car R3 support
     + Power domains for Rockchip RK3366

   - Misc updates and smaller fixes for TEE and memory driver
     subsystems"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  firmware: arm_scpi: fix endianness of dev_id in struct dev_pstate_set
  soc/tegra: fuse: Add missing semi-colon
  soc/tegra: Restrict SoC device registration to Tegra
  drivers: soc: sunxi: add support for A64 and its SRAM C
  drivers: soc: sunxi: add support for remapping func value to reg value
  drivers: soc: sunxi: fix error processing on base address when claiming
  dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
  bus: sunxi-rsb: Enable by default for ARM64
  soc/tegra: Register SoC device
  firmware: tegra: set drvdata earlier
  memory: Convert to using %pOF instead of full_name
  soc: Convert to using %pOF instead of full_name
  bus: Convert to using %pOF instead of full_name
  firmware: Convert to using %pOF instead of full_name
  soc: mediatek: add SCPSYS power domain driver for MediaTek MT7622 SoC
  soc: mediatek: add header files required for MT7622 SCPSYS dt-binding
  soc: mediatek: reduce code duplication of scpsys_probe across all SoCs
  dt-bindings: soc: update the binding document for SCPSYS on MediaTek MT7622 SoC
  reset: uniphier: add analog amplifiers reset control
  reset: uniphier: add video input subsystem reset control
  ...
Merge tag 'sunxi-drivers-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/drivers 2017-08-21T07:25:22+00:00 Arnd Bergmann arnd@arndb.de 2017-08-21T07:25:22+00:00 2e9a41dca33f06ec46aad332f17e2fcc07d20578 Pull "Allwinner driver changes for 4.14" from Chen-Yu Tsai: Usual driver changes: - SUNXI_RSB bus driver enabled by default for ARM64 - Support for SRAM controller and SRAM C block on the A64 added * tag 'sunxi-drivers-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: drivers: soc: sunxi: add support for A64 and its SRAM C drivers: soc: sunxi: add support for remapping func value to reg value drivers: soc: sunxi: fix error processing on base address when claiming dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C bus: sunxi-rsb: Enable by default for ARM64 
Pull "Allwinner driver changes for 4.14" from Chen-Yu Tsai:

Usual driver changes:

  - SUNXI_RSB bus driver enabled by default for ARM64

  - Support for SRAM controller and SRAM C block on the A64 added

* tag 'sunxi-drivers-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  drivers: soc: sunxi: add support for A64 and its SRAM C
  drivers: soc: sunxi: add support for remapping func value to reg value
  drivers: soc: sunxi: fix error processing on base address when claiming
  dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
  bus: sunxi-rsb: Enable by default for ARM64
Merge tag 'omap-for-v4.14/fixes-not-urgent-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup 2017-08-18T22:07:56+00:00 Arnd Bergmann arnd@arndb.de 2017-08-18T22:07:56+00:00 2ad93fa37fdd7f5525333240633557effacb28ff Pull "non-urgent fixes for omaps for v4.14" from Tony Lindgren: Non-urgent fixes for omaps for v4.14 merge window. These all can wait for the merge window as we have not seemed to hit any of these so far: - Fix error handling in omap_ocp2scp_probe affecting runtime PM error path - Drop broken RPM status update for omap_device - Two fixes for of_irq_get() usage that can return 0 * tag 'omap-for-v4.14/fixes-not-urgent-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP4+: PRM: fix of_irq_get() result checks ARM: OMAP3+: PRM: fix of_irq_get() result check ARM: OMAP2+: omap_device: drop broken RPM status update from suspend_noirq bus: omap-ocp2scp: Fix error handling in omap_ocp2scp_probe 
Pull "non-urgent fixes for omaps for v4.14" from Tony Lindgren:

Non-urgent fixes for omaps for v4.14 merge window. These all
can wait for the merge window as we have not seemed to hit
any of these so far:

- Fix error handling in omap_ocp2scp_probe affecting runtime
  PM error path

- Drop broken RPM status update for omap_device

- Two fixes for of_irq_get() usage that can return 0

* tag 'omap-for-v4.14/fixes-not-urgent-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP4+: PRM: fix of_irq_get() result checks
  ARM: OMAP3+: PRM: fix of_irq_get() result check
  ARM: OMAP2+: omap_device: drop broken RPM status update from suspend_noirq
  bus: omap-ocp2scp: Fix error handling in omap_ocp2scp_probe
bus: sunxi-rsb: Enable by default for ARM64 2017-08-18T06:30:15+00:00 Jagan Teki jagan@amarulasolutions.com 2017-08-12T05:40:41+00:00 dc1a37b2b9eda3b9847f39c18b3d443dad64d54c Allwinner's A64 SoC uses the "Reduced Serial Bus" to communicate with its companion PMIC. Since arm64 does not have separate defconfigs for each platform or processor family, enable this driver by default for ARM64 as well. Note that the Kconfig symbol already depends on ARCH_SUNXI. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> [wens@csie.org: Refined commit message] Signed-off-by: Chen-Yu Tsai <wens@csie.org> 
Allwinner's A64 SoC uses the "Reduced Serial Bus" to communicate with
its companion PMIC.

Since arm64 does not have separate defconfigs for each platform or
processor family, enable this driver by default for ARM64 as well.
Note that the Kconfig symbol already depends on ARCH_SUNXI.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[wens@csie.org: Refined commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
bus: Convert to using %pOF instead of full_name 2017-08-16T15:21:40+00:00 Rob Herring robh@kernel.org 2017-07-18T21:42:51+00:00 9c0982d809fd81cc63438926c465e5919fd97acd Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> 
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.

Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
bus: uniphier-system-bus: set up registers when resuming 2017-08-04T10:57:18+00:00 Masahiro Yamada yamada.masahiro@socionext.com 2017-07-31T05:49:25+00:00 2f4233ee13fb89b70e56b2df7789e2a3d131c85e When resuming, set up registers that have been lost in the sleep state. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> 
When resuming, set up registers that have been lost in the sleep state.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
bus: omap-ocp2scp: Fix error handling in omap_ocp2scp_probe 2017-07-12T09:25:41+00:00 Kishon Vijay Abraham I kishon@ti.com 2017-07-11T10:16:38+00:00 672647afabf5bafd3d855724ee5829e2a9cbd65b The error handling code in omap_ocp2scp_probe fails to invoke pm_runtime_disable and fails to initialize return value in certain cases. Fix it here. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> 
The error handling code in omap_ocp2scp_probe fails to invoke
pm_runtime_disable and fails to initialize return value in
certain cases. Fix it here.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux 2017-07-10T01:48:37+00:00 Linus Torvalds torvalds@linux-foundation.org 2017-07-10T01:48:37+00:00 af3c8d98508d37541d4bf57f13a984a7f73a328c Pull drm updates from Dave Airlie: "This is the main pull request for the drm, I think I've got one later driver pull for mediatek SoC driver, I'm undecided on if it needs to go to you yet. Otherwise summary below: Core drm: - Atomic add driver private objects - Deprecate preclose hook in modern drivers - MST bandwidth tracking - Use kvmalloc in more places - Add mode_valid hook for crtc/encoder/bridge - Reduce sync_file construction time - Documentation updates - New DRM synchronisation object support New drivers: - pl111 - pl111 CLCD display controller Panel: - Innolux P079ZCA panel driver - Add NL12880B20-05, NL192108AC18-02D, P320HVN03 panels - panel-samsung-s6e3ha2: Add s6e3hf2 panel support i915: - SKL+ watermark fixes - G4x/G33 reset improvements - DP AUX backlight improvements - Buffer based GuC/host communication - New getparam for (sub)slice infomation - Cannonlake and Coffeelake initial patches - Execbuf optimisations radeon/amdgpu: - Lots of Vega10 bug fixes - Preliminary raven support - KIQ support for compute rings - MEC queue management rework - DCE6 Audio support - SR-IOV improvements - Better radeon/amdgpu selection support nouveau: - HDMI stereoscopic support - Display code rework for >= GM20x GPUs msm: - GEM rework for fine-grained locking - Per-process pagetable work - HDMI fixes for Snapdragon 820. vc4: - Remove 256MB CMA limit from vc4 - Add out-fence support - Add support for cygnus - Get/set tiling ioctls support - Add T-format tiling support for scanout zte: - add VGA support. etnaviv: - Thermal throttle support for newer GPUs - Restore userspace buffer cache performance - dma-buf sync fix stm: - add stm32f429 display support exynos: - Rework vblank handling - Fixup sw-trigger code sun4i: - V3s display engine support - HDMI support for older SoCs - Preliminary work on dual-pipeline SoCs. rcar-du: - VSP work imx-drm: - Remove counter load enable from PRE - Double read/write reduction flag support tegra: - Documentation for the host1x and drm driver. - Lots of staging ioctl fixes due to grate project work. omapdrm: - dma-buf fence support - TILER rotation fixes" * tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux: (1270 commits) drm: Remove unused drm_file parameter to drm_syncobj_replace_fence() drm/amd/powerplay: fix bug fail to remove sysfs when rmmod amdgpu. amdgpu: Set cik/si_support to 1 by default if radeon isn't built drm/amdgpu/gfx9: fix driver reload with KIQ drm/amdgpu/gfx8: fix driver reload with KIQ drm/amdgpu: Don't call amd_powerplay_destroy() if we don't have powerplay drm/ttm: Fix use-after-free in ttm_bo_clean_mm drm/amd/amdgpu: move get memory type function from early init to sw init drm/amdgpu/cgs: always set reference clock in mode_info drm/amdgpu: fix vblank_time when displays are off drm/amd/powerplay: power value format change for Vega10 drm/amdgpu/gfx9: support the amdgpu.disable_cu option drm/amd/powerplay: change PPSMC_MSG_GetCurrPkgPwr for Vega10 drm/amdgpu: Make amdgpu_cs_parser_init static (v2) drm/amdgpu/cs: fix a typo in a comment drm/amdgpu: Fix the exported always on CU bitmap drm/amdgpu/gfx9: gfx_v9_0_enable_gfx_static_mg_power_gating() can be static drm/amdgpu/psp: upper_32_bits/lower_32_bits for address setup drm/amd/powerplay/cz: print message if smc message fails drm/amdgpu: fix typo in amdgpu_debugfs_test_ib_init ... 
Pull drm updates from Dave Airlie:
 "This is the main pull request for the drm, I think I've got one later
  driver pull for mediatek SoC driver, I'm undecided on if it needs to
  go to you yet.

  Otherwise summary below:

  Core drm:
   - Atomic add driver private objects
   - Deprecate preclose hook in modern drivers
   - MST bandwidth tracking
   - Use kvmalloc in more places
   - Add mode_valid hook for crtc/encoder/bridge
   - Reduce sync_file construction time
   - Documentation updates
   - New DRM synchronisation object support

  New drivers:
   - pl111 - pl111 CLCD display controller

  Panel:
   - Innolux P079ZCA panel driver
   - Add NL12880B20-05, NL192108AC18-02D, P320HVN03 panels
   - panel-samsung-s6e3ha2: Add s6e3hf2 panel support

  i915:
   - SKL+ watermark fixes
   - G4x/G33 reset improvements
   - DP AUX backlight improvements
   - Buffer based GuC/host communication
   - New getparam for (sub)slice infomation
   - Cannonlake and Coffeelake initial patches
   - Execbuf optimisations

  radeon/amdgpu:
   - Lots of Vega10 bug fixes
   - Preliminary raven support
   - KIQ support for compute rings
   - MEC queue management rework
   - DCE6 Audio support
   - SR-IOV improvements
   - Better radeon/amdgpu selection support

  nouveau:
   - HDMI stereoscopic support
   - Display code rework for >= GM20x GPUs

  msm:
   - GEM rework for fine-grained locking
   - Per-process pagetable work
   - HDMI fixes for Snapdragon 820.

  vc4:
   - Remove 256MB CMA limit from vc4
   - Add out-fence support
   - Add support for cygnus
   - Get/set tiling ioctls support
   - Add T-format tiling support for scanout

  zte:
   - add VGA support.

  etnaviv:
   - Thermal throttle support for newer GPUs
   - Restore userspace buffer cache performance
   - dma-buf sync fix

  stm:
   - add stm32f429 display support

  exynos:
   - Rework vblank handling
   - Fixup sw-trigger code

  sun4i:
   - V3s display engine support
   - HDMI support for older SoCs
   - Preliminary work on dual-pipeline SoCs.

  rcar-du:
   - VSP work

  imx-drm:
   - Remove counter load enable from PRE
   - Double read/write reduction flag support

  tegra:
   - Documentation for the host1x and drm driver.
   - Lots of staging ioctl fixes due to grate project work.

  omapdrm:
   - dma-buf fence support
   - TILER rotation fixes"

* tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux: (1270 commits)
  drm: Remove unused drm_file parameter to drm_syncobj_replace_fence()
  drm/amd/powerplay: fix bug fail to remove sysfs when rmmod amdgpu.
  amdgpu: Set cik/si_support to 1 by default if radeon isn't built
  drm/amdgpu/gfx9: fix driver reload with KIQ
  drm/amdgpu/gfx8: fix driver reload with KIQ
  drm/amdgpu: Don't call amd_powerplay_destroy() if we don't have powerplay
  drm/ttm: Fix use-after-free in ttm_bo_clean_mm
  drm/amd/amdgpu: move get memory type function from early init to sw init
  drm/amdgpu/cgs: always set reference clock in mode_info
  drm/amdgpu: fix vblank_time when displays are off
  drm/amd/powerplay: power value format change for Vega10
  drm/amdgpu/gfx9: support the amdgpu.disable_cu option
  drm/amd/powerplay: change PPSMC_MSG_GetCurrPkgPwr for Vega10
  drm/amdgpu: Make amdgpu_cs_parser_init static (v2)
  drm/amdgpu/cs: fix a typo in a comment
  drm/amdgpu: Fix the exported always on CU bitmap
  drm/amdgpu/gfx9: gfx_v9_0_enable_gfx_static_mg_power_gating() can be static
  drm/amdgpu/psp: upper_32_bits/lower_32_bits for address setup
  drm/amd/powerplay/cz: print message if smc message fails
  drm/amdgpu: fix typo in amdgpu_debugfs_test_ib_init
  ...