[ Upstream commit 0c2aa0e4b308815e877601845c1a89913f9bd2b9 ]

The GISB bus can support addresses beyond 32-bits.  So this commit
corrects support for reading a captured 64-bit address into a 64-bit
variable by obtaining the high bits from the ARB_ERR_CAP_HI_ADDR
register (when present) and then outputting the full 64-bit value.

It also removes unused definitions.

Fixes: 44127b771d9c ("bus: add Broadcom GISB bus arbiter timeout/error handler")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>

[ Upstream commit c7f5828bf77dcbd61d51f4736c1d5aa35663fbb4 ]

When the PMU driver is built as a module, the perf expects the
pmu->module to be valid, so that the driver is prevented from
being unloaded while it is in use. Fix the CCN pmu driver to
fill in this field.

Fixes: a33b0daab73a0 ("bus: ARM CCN PMU driver")
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>

[ Upstream commit 2bbbd96357ce76cc45ec722c00f654aa7b189112 ]

At least the Armada XP SoC supports 4GB on a single DRAM window. Because
the size register values contain the actual size - 1, the MSB is set in
that case. For example, the SDRAM window's control register's value is
0xffffffe1 for 4GB (bits 31 to 24 contain the size).

The MBUS driver reads back each window's size from registers and
calculates the actual size as (control_reg | ~DDR_SIZE_MASK) + 1, which
overflows for 32 bit values, resulting in other miscalculations further
on (a bad RAM window for the CESA crypto engine calculated by
mvebu_mbus_setup_cpu_target_nooverlap() in my case).

This patch changes the type in 'struct mbus_dram_window' from u32 to
u64, which allows us to keep using the same register calculation code in
most MBUS-using drivers (which calculate ->size - 1 again).

Fixes: fddddb52a6c4 ("bus: introduce an Marvell EBU MBus driver")
CC: stable@vger.kernel.org
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 4e486cba285ff06a1f28f0fc2991dde1482d1dcf ]

The "Miscellaneous Node" fell through cracks of node initialisation,
as its ID is shared with HN-I.

This patch treats MN as a special case (which it is), adding separate
validation check for it and pre-defining the node ID in relevant events
descriptions. That way one can simply run:

	# perf stat -a -e ccn/mn_ecbarrier/ <workload>

Additionally, direction in the MN pseudo-events XP watchpoint
definitions is corrected to be "TX" (1) as they are defined from the
crosspoint point of view (thus barriers are transmitted from XP to MN).

Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 8f06c51fac1ca4104b8b64872f310e28186aea42 ]

Since 688d4dfcdd624192cbf03c08402e444d1d11f294 "perf tools: Support
parsing parameterized events" the perf userspace tools understands
"argument=?" syntax in the events file, making sure that required
arguments are provided by the user and not defaulting to 0, causing
confusion.

This patch adds the required arguments lists for CCN events.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit b928466b2169e061822daad48ecf55b005445547 ]

The code setting XP watchpoint comparator and mask registers should, in
order to be fully compliant with specification, zero one or more most
significant bits of each field. In both L cases it means zeroing bit 63.
The bitmask doing this was wrong, though, zeroing bit 60 instead.
Fortunately, due to a lucky coincidence, this turned out to be fairly
innocent with the existing hardware.

Fixed now.

Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit b7c1beb278e8e3dc664ed3df3fc786db126120a9 ]

Fuzzing the CCN perf driver revealed a small but definitely dangerous
mistake in the event setup code. When a cycle counter is requested, the
driver should not reconfigure the events bus at all, otherwise it will
corrupt (in most but the simplest cases) its configuration and may end
up accessing XP array out of its bounds and corrupting control
registers.

Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 33b96d2c9579213cf3f36d7b29841b1e464750c4 ]

Currently we have an incorrect behaviour when multiple devices
are present under the weim node. For example:

&weim {
	...
	status = "okay";

	sram@0,0 {
		...
        	status = "okay";
	};

	mram@0,0 {
		...
        	status = "disabled";
    	};
};

In this case only the 'sram' device should be probed and not 'mram'.

However what happens currently is that the status variable is ignored,
causing the 'sram' device to be disabled and 'mram' to be enabled.

Change the weim_parse_dt() function to use
for_each_available_child_of_node()so that the devices marked with
'status = disabled' are not probed.

Cc: <stable@vger.kernel.org>
Suggested-by: Wolfgang Netbal <wolfgang.netbal@sigmatek.at>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

commit a18f8e97fe69195823d7fb5c68a8d6565f39db4b upstream.

Events defined as watchpoints on nodes must have their config values
converted so that they apply to the respective node's XP. The
function setting new values was using wrong mask for the "port" field,
resulting in corrupted value. Fixed now.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge "mvebu fixes for 4.1 (part 3)" from Gregory CLEMENT:

Disable unused internal RTC for Mamba from linksys (Armada XP)
And 2 commits fixing regressions on mvebu-mbus:
- the first one for Kirkwood or Orion SoC
- the second one for DMA when the platform have more than 4GB (only
  possible on Armada XP as far as I know)

* tag 'mvebu-fixes-4.1-3' of git://git.infradead.org/linux-mvebu:
  Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
  bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
  ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC