linux-stable.git/drivers/bluetooth, branch v6.1.90

Bluetooth: qca: fix NULL-deref on non-serdev suspend

2024-05-02T14:29:28+00:00

commit 73e87c0a49fda31d7b589edccf4c72e924411371 upstream.

Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.

Add the missing sanity check to prevent a NULL-pointer dereference when
wakeup() is called for a non-serdev controller during suspend.

Just return true for now to restore the original behaviour and address
the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c657
("Bluetooth: hci_qca: only assign wakeup with serial port support") that
causes the crash to happen already at setup() time.

Fixes: c1a74160eaf1 ("Bluetooth: hci_qca: Add device_may_wakeup support")
Cc: stable@vger.kernel.org      # 5.13
Signed-off-by: Johan Hovold 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Greg Kroah-Hartman

Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0bda:0x4853

2024-05-02T14:29:28+00:00

commit d1a5a7eede2977da3d2002d5ea3b519019cc1a98 upstream.

Add the support ID(0x0bda, 0x4853) to usb_device_id table for
Realtek RTL8852BE.

Without this change the device utilizes an obsolete version of
the firmware that is encoded in it rather than the updated Realtek
firmware and config files from the firmware directory. The latter
files implement many new features.

The device table is as follows:

T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=4853 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms

Cc: stable@vger.kernel.org
Signed-off-by: Larry Finger 
Signed-off-by: WangYuli 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Greg Kroah-Hartman

Bluetooth: qca: set power_ctrl_enabled on NULL returned by gpiod_get_optional()

2024-05-02T14:29:25+00:00

[ Upstream commit 3d05fc82237aa97162d0d7dc300b55bb34e91d02 ]

Any return value from gpiod_get_optional() other than a pointer to a
GPIO descriptor or a NULL-pointer is an error and the driver should
abort probing. That being said: commit 56d074d26c58 ("Bluetooth: hci_qca:
don't use IS_ERR_OR_NULL() with gpiod_get_optional()") no longer sets
power_ctrl_enabled on NULL-pointer returned by
devm_gpiod_get_optional(). Restore this behavior but bail-out on errors.
While at it: also bail-out on error returned when trying to get the
"swctrl" GPIO.

Reported-by: Wren Turkal 
Reported-by: Zijun Hu 
Closes: https://lore.kernel.org/linux-bluetooth/1713449192-25926-2-git-send-email-quic_zijuhu@quicinc.com/
Fixes: 56d074d26c58 ("Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()")
Reviewed-by: Krzysztof Kozlowski 
Signed-off-by: Bartosz Golaszewski 
Tested-by: Wren Turkal 
Reported-by: Wren Turkal 
Reported-by: Zijun Hu 
Reviewed-by: Krzysztof Kozlowski
Reviewed-by: Krzysztof Kozlowski 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: btintel: Fixe build regression

2024-04-13T11:05:27+00:00

commit 6e62ebfb49eb65bdcbfc5797db55e0ce7f79c3dd upstream.

This fixes the following build regression:

drivers-bluetooth-btintel.c-btintel_read_version()-warn:
passing-zero-to-PTR_ERR

Fixes: b79e04091010 ("Bluetooth: btintel: Fix null ptr deref in btintel_read_version")
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Greg Kroah-Hartman

Bluetooth: btmtk: Add MODULE_FIRMWARE() for MT7922

2024-04-13T11:05:03+00:00

[ Upstream commit 3e465a07cdf444140f16bc57025c23fcafdde997 ]

Since dracut refers to the module info for defining the required
firmware files and btmtk driver doesn't provide the firmware info for
MT7922, the generate initrd misses the firmware, resulting in the
broken Bluetooth.

This patch simply adds the MODULE_FIRMWARE() for the missing entry
for covering that.

Link: https://bugzilla.suse.com/show_bug.cgi?id=1214133
Signed-off-by: Takashi Iwai 
Reviewed-by: Paul Menzel 
Reviewed-by: Matthias Brugger 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: btintel: Fix null ptr deref in btintel_read_version

2024-04-13T11:05:03+00:00

[ Upstream commit b79e040910101b020931ba0c9a6b77e81ab7f645 ]

If hci_cmd_sync_complete() is triggered and skb is NULL, then
hdev->req_skb is NULL, which will cause this issue.

Reported-and-tested-by: syzbot+830d9e3fa61968246abd@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: qca: fix device-address endianness

2024-04-10T14:28:24+00:00

commit 77f45cca8bc55d00520a192f5a7715133591c83e upstream.

The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.

Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).

Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.

Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.

The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.

Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.

Fixes: 5c0a1001c8be ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org      # 5.1
Cc: Balakrishna Godavarthi 
Cc: Matthias Kaehlcke 
Tested-by: Nikita Travkin  # sc7180
Reviewed-by: Douglas Anderson 
Signed-off-by: Johan Hovold 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Greg Kroah-Hartman

Revert "Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT"

2024-04-10T14:28:24+00:00

commit 4790a73ace86f3d165bbedba898e0758e6e1b82d upstream.

This reverts commit 7dcd3e014aa7faeeaf4047190b22d8a19a0db696.

Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.

A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.

Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc81a ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.

Fixes: 7dcd3e014aa7 ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org      # 6.8
Cc: Janaki Ramaiah Thota 
Signed-off-by: Johan Hovold 
Reported-by: Clayton Craft 
Tested-by: Clayton Craft 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Greg Kroah-Hartman

Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()

2024-03-26T22:20:40+00:00

[ Upstream commit 56d074d26c5828773b00b2185dd7e1d08273b8e8 ]

The optional variants for the gpiod_get() family of functions return NULL
if the GPIO in question is not associated with this device. They return
ERR_PTR() on any other error. NULL descriptors are graciously handled by
GPIOLIB and can be safely passed to any of the GPIO consumer interfaces
as they will return 0 and act as if the function succeeded. If one is
using the optional variant, then there's no point in checking for NULL.

Fixes: 6845667146a2 ("Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe")
Signed-off-by: Bartosz Golaszewski 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT

2024-03-06T14:45:08+00:00

[ Upstream commit 7dcd3e014aa7faeeaf4047190b22d8a19a0db696 ]

BT adapter going into UNCONFIGURED state during BT turn ON when
devicetree has no local-bd-address node.

Bluetooth will not work out of the box on such devices, to avoid this
problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on
local-bd-address node entry.

When this quirk is not set, the public Bluetooth address read by host
from controller though HCI Read BD Address command is
considered as valid.

Fixes: e668eb1e1578 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Janaki Ramaiah Thota 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin