linux-stable.git/drivers/bluetooth, branch linux-5.4.y

Bluetooth: btusb: reorder cleanup in btusb_disconnect to avoid UAF

2025-12-03T11:45:16+00:00

[ Upstream commit 23d22f2f71768034d6ef86168213843fc49bf550 ]

There is a KASAN: slab-use-after-free read in btusb_disconnect().
Calling "usb_driver_release_interface(&btusb_driver, data->intf)" will
free the btusb data associated with the interface. The same data is
then used later in the function, hence the UAF.

Fix by moving the accesses to btusb data to before the data is free'd.

Reported-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2fc81b50a4f8263a159b
Tested-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com
Fixes: fd913ef7ce619 ("Bluetooth: btusb: Add out-of-band wakeup support")
Signed-off-by: Raphael Pinsonneault-Thibeault 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: bcsp: receive data only if registered

2025-12-03T11:45:14+00:00

[ Upstream commit ca94b2b036c22556c3a66f1b80f490882deef7a6 ]

Currently, bcsp_recv() can be called even when the BCSP protocol has not
been registered. This leads to a NULL pointer dereference, as shown in
the following stack trace:

    KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
    RIP: 0010:bcsp_recv+0x13d/0x1740 drivers/bluetooth/hci_bcsp.c:590
    Call Trace:
     
     hci_uart_tty_receive+0x194/0x220 drivers/bluetooth/hci_ldisc.c:627
     tiocsti+0x23c/0x2c0 drivers/tty/tty_io.c:2290
     tty_ioctl+0x626/0xde0 drivers/tty/tty_io.c:2706
     vfs_ioctl fs/ioctl.c:51 [inline]
     __do_sys_ioctl fs/ioctl.c:907 [inline]
     __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893
     do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
     do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
     entry_SYSCALL_64_after_hwframe+0x77/0x7f

To prevent this, ensure that the HCI_UART_REGISTERED flag is set before
processing received data. If the protocol is not registered, return
-EUNATCH.

Reported-by: syzbot+4ed6852d4da4606c93da@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=4ed6852d4da4606c93da
Tested-by: syzbot+4ed6852d4da4606c93da@syzkaller.appspotmail.com
Signed-off-by: Ivan Pravdin 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: btrtl: Prevent potential NULL dereference

2025-05-02T05:39:19+00:00

[ Upstream commit 324dddea321078a6eeb535c2bff5257be74c9799 ]

The btrtl_initialize() function checks that rtl_load_file() either
had an error or it loaded a zero length file.  However, if it loaded
a zero length file then the error code is not set correctly.  It
results in an error pointer vs NULL bug, followed by a NULL pointer
dereference.  This was detected by Smatch:

drivers/bluetooth/btrtl.c:592 btrtl_initialize() warn: passing zero to 'ERR_PTR'

Fixes: 26503ad25de8 ("Bluetooth: btrtl: split the device initialization into smaller parts")
Signed-off-by: Dan Carpenter 
Reviewed-by: Hans de Goede 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: hci_uart: Fix another race during initialization

2025-05-02T05:39:18+00:00

commit 5df5dafc171b90d0b8d51547a82657cd5a1986c7 upstream.

Do not set 'HCI_UART_PROTO_READY' before call 'hci_uart_register_dev()'.
Possible race is when someone calls 'hci_tty_uart_close()' after this bit
is set, but 'hci_uart_register_dev()' wasn't done. This leads to access
to uninitialized fields. To fix it let's set this bit after device was
registered (as before patch c411c62cc133) and to fix previous problem let's
add one more bit in addition to 'HCI_UART_PROTO_READY' which allows to
perform power up without original bit set (pls see commit c411c62cc133).

Crash backtrace from syzbot report:

RIP: 0010:skb_queue_empty_lockless include/linux/skbuff.h:1887 [inline]
RIP: 0010:skb_queue_purge_reason+0x6d/0x140 net/core/skbuff.c:3936

Call Trace:
 
 skb_queue_purge include/linux/skbuff.h:3364 [inline]
 mrvl_close+0x2f/0x90 drivers/bluetooth/hci_mrvl.c:100
 hci_uart_tty_close+0xb6/0x120 drivers/bluetooth/hci_ldisc.c:557
 tty_ldisc_close drivers/tty/tty_ldisc.c:455 [inline]
 tty_ldisc_kill+0x66/0xc0 drivers/tty/tty_ldisc.c:613
 tty_ldisc_release+0xc9/0x120 drivers/tty/tty_ldisc.c:781
 tty_release_struct+0x10/0x80 drivers/tty/tty_io.c:1690
 tty_release+0x4ef/0x640 drivers/tty/tty_io.c:1861
 __fput+0x86/0x2a0 fs/file_table.c:450
 task_work_run+0x82/0xb0 kernel/task_work.c:239
 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
 exit_to_user_mode_loop kernel/entry/common.c:114 [inline]
 exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline]
 __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline]
 syscall_exit_to_user_mode+0xa3/0x1b0 kernel/entry/common.c:218
 do_syscall_64+0x9a/0x190 arch/x86/entry/common.c:89
 entry_SYSCALL_64_after_hwframe+0x77/0x7f

Signed-off-by: Arseniy Krasnov 
Reported-by: syzbot+683f8cb11b94b1824c77@syzkaller.appspotmail.com
Tested-by: syzbot+683f8cb11b94b1824c77@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-bluetooth/d159c57f-8490-4c26-79da-6ad3612c4a14@salutedevices.com/
Fixes: 366ceff495f9 ("Bluetooth: hci_uart: fix race during initialization")
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Greg Kroah-Hartman

Bluetooth: hci_uart: fix race during initialization

2025-05-02T05:39:11+00:00

[ Upstream commit 366ceff495f902182d42b6f41525c2474caf3f9a ]

'hci_register_dev()' calls power up function, which is executed by
kworker - 'hci_power_on()'. This function does access to bluetooth chip
using callbacks from 'hci_ldisc.c', for example 'hci_uart_send_frame()'.
Now 'hci_uart_send_frame()' checks 'HCI_UART_PROTO_READY' bit set, and
if not - it fails. Problem is that 'HCI_UART_PROTO_READY' is set after
'hci_register_dev()', and there is tiny chance that 'hci_power_on()' will
be executed before setting this bit. In that case HCI init logic fails.

Patch moves setting of 'HCI_UART_PROTO_READY' before calling function
'hci_uart_register_dev()'.

Signed-off-by: Arseniy Krasnov 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: btusb: Add RTL8852BE device 0489:e123 to device tables

2024-12-14T18:44:52+00:00

[ Upstream commit 69b84ffce260ff13826dc10aeb3c3e5c2288a552 ]

Add the support ID 0489:e123 to usb_device_id table for
Realtek RTL8852B chip.

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#=  7 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e123 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Hilda Wu 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: btusb: Fix regression with fake CSR controllers 0a12:0001

2024-11-08T15:20:48+00:00

commit 2c1dda2acc4192d826e84008d963b528e24d12bc upstream.

Fake CSR controllers don't seem to handle short-transfer properly which
cause command to time out:

kernel: usb 1-1: new full-speed USB device number 19 using xhci_hcd
kernel: usb 1-1: New USB device found, idVendor=0a12, idProduct=0001, bcdDevice=88.91
kernel: usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
kernel: usb 1-1: Product: BT DONGLE10
...
Bluetooth: hci1: Opcode 0x1004 failed: -110
kernel: Bluetooth: hci1: command 0x1004 tx timeout

According to USB Spec 2.0 Section 5.7.3 Interrupt Transfer Packet Size
Constraints a interrupt transfer is considered complete when the size is 0
(ZPL) or < wMaxPacketSize:

 'When an interrupt transfer involves more data than can fit in one
 data payload of the currently established maximum size, all data
 payloads are required to be maximum-sized except for the last data
 payload, which will contain the remaining data. An interrupt transfer
 is complete when the endpoint does one of the following:

 • Has transferred exactly the amount of data expected
 • Transfers a packet with a payload size less than wMaxPacketSize or
 transfers a zero-length packet'

Link: https://bugzilla.kernel.org/show_bug.cgi?id=219365
Fixes: 7b05933340f4 ("Bluetooth: btusb: Fix not handling ZPL/short-transfer")
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Greg Kroah-Hartman

Bluetooth: btmrvl: Use IRQF_NO_AUTOEN flag in request_irq()

2024-11-08T15:20:36+00:00

[ Upstream commit 7b1ab460592ca818e7b52f27cd3ec86af79220d1 ]

disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.

Fixes: bb7f4f0bcee6 ("btmrvl: add platform specific wakeup interrupt support")
Signed-off-by: Jinjie Ruan 
Signed-off-by: Luiz Augusto von Dentz 
Signed-off-by: Sasha Levin

Bluetooth: btmrvl_sdio: Refactor irq wakeup

2024-11-08T15:20:36+00:00

[ Upstream commit e660b3510eb4b3c06ce1188a1d305b6f653106fc ]

Use device_init_wakeup to allow the Bluetooth dev to wake the system
from suspend. Currently, the device can wake the system but no
power/wakeup entry is created in sysfs to allow userspace to disable
wakeup.

Signed-off-by: Abhishek Pandit-Subedi 
Reviewed-by: Douglas Anderson 
Signed-off-by: Marcel Holtmann 
Stable-dep-of: 7b1ab460592c ("Bluetooth: btmrvl: Use IRQF_NO_AUTOEN flag in request_irq()")
Signed-off-by: Sasha Levin

Bluetooth: btusb: Fix not handling ZPL/short-transfer

2024-11-08T15:20:27+00:00

[ Upstream commit 7b05933340f4490ef5b09e84d644d12484b05fdf ]

Requesting transfers of the exact same size of wMaxPacketSize may result
in ZPL/short-transfer since the USB stack cannot handle it as we are
limiting the buffer size to be the same as wMaxPacketSize.

Also, in terms of throughput this change has the same effect to
interrupt endpoint as 290ba200815f "Bluetooth: Improve USB driver throughput
by increasing the frame size" had for the bulk endpoint, so users of the
advertisement bearer (e.g. BT Mesh) may benefit from this change.

Fixes: 5e23b923da03 ("[Bluetooth] Add generic driver for Bluetooth USB devices")
Signed-off-by: Luiz Augusto von Dentz 
Tested-by: Kiran K 
Signed-off-by: Sasha Levin