Submitting the bulk URBs for ACL data transfers only on demand has no real benefit compared to just submit them when a Bluetooth device gets opened. So when submitting the interrupt URBs for HCI events, just submit the bulk URBs, too. This solves a problem with some Bluetooth USB dongles that has been reported over the last few month. These devices require that the bulk URBs are actually present. These devices are really broken, but there is nothing we can do about it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to allow debugging without having to recompile the kernel. This patch turns all BT_DBG() calls into pr_debug() to support dynamic debug messages. As a side effect all CONFIG_BT_*_DEBUG statements are now removed and some broken debug entries have been fixed. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch allows the Asus WL-BTD202 dongle to be used with a mono headset without having to specify "options btusb force_scofix=1". Based on a patch from Guillaume Bedot <littletux@zarb.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth subsystem was not using the HCI Reset command when doing device initialization. The Bluetooth 1.0b specification was ambiguous on how the device firmware was suppose to handle it. Almost every device was triggering a transport reset at the same time. In case of USB this ended up in disconnects from the bus. All modern Bluetooth dongles handle this perfectly fine and a lot of them actually require that HCI Reset is sent. If not then they are either stuck in their HID Proxy mode or their internal structures for inquiry and paging are not correctly setup. To handle old and new devices smoothly the Bluetooth subsystem contains a quirk to force the HCI Reset on initialization. However maintaining such a quirk becomes more and more complicated. This patch turns the logic around and lets the old devices disable the HCI Reset command. The only device where the HCI_QUIRK_NO_RESET is still needed are the original Digianswer devices and dongles with an early CSR firmware. CSR reported that they fixed this for version 12 firmware. The last official release of version 11 firmware is build ID 115. The first version 12 candidate was build ID 117. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During suspend it is important that all URBs are cancelled and then on resume re-submitted. This gives initial suspend/resume support. Based on initial work from Oliver Neukum <oneukum@suse.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the addition of usb_unlink_anchored_urbs() it is possible to fully control the bulk URBs from the notify callback. There is no need to schedule work and so only do this for the ISOC URBs. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The URB submission routines need more fine grained control for the mem_flags used by kmalloc(), usb_alloc_urb() and usb_submit_urb() to better support different caller situations. Add a mem_flags parameter and give the caller full control. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new A-Link Bluetooth dongle is another one based on the BCM2046 chip from Broadcom and it also needs to send HCI_Reset before it becomes fully operational. Without the quirk it will show a lot of I/O errors. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Targus and Belkin have come out with new Bluetooth 2.1 capable dongles using the latest BCM2046 chip from Broadcom. Both of them are so called HID proxy dongles and they need to send HCI_Reset before they become fully operational. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The transfer buffer of an URB will be automatically freed when using the URB_FREE_BUFFER transfer_flag. So the extra calls to kfree() will cause a double free. Reported-by: Justin Mattock <justinmattock@gmail.com> Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>