commit 15b8d2c41fe5839582029f65c5f7004db451cc2b upstream.

In big endian mode regmap_bulk_read gives incorrect data
for byte reads.

This is because memcpy of a single byte from an address
after full word read gives different results when
endianness differs. ie. we get little-end in LE and big-end in BE.

Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
[lizf: Backported to 3.4: format_val() takes only two arguments]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit d6b41cb06044a7d895db82bdd54f6e4219970510 upstream.

Since we cannot make sure the 'val_count' will always be none zero
here, and then if it equals to zero, the kmemdup() will return
ZERO_SIZE_PTR, which equals to ((void *)16).

So this patch fix this with just doing the zero check before calling
kmemdup().

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
[lizf: Backported to 3.4: release mutex before returning EINVAL]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 5844a8b9d98ec11ce1d77610daacf3f0a0e14715 upstream.

A previous over-zealous factorisation of code means that we only treat
registers as volatile if they are readable. For most devices this is fine
since normally most registers can be read and volatility implies
readability but for format_write() devices where there is no readback from
the hardware and we use volatility to mean simply uncacheability this means
that we end up treating all registers as cacheble.

A bigger refactoring of the code to clarify this is in order but as a fix
make a minimal change and only check readability when checking volatility
if there is no format_write() operation defined for the device.

Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit a8f28cfad8cd44d7c34b166d0e5ace1125dbee1f upstream.

Building regmap.o triggers this GCC warning:
    drivers/base/regmap/regmap.c: In function ‘regmap_raw_read’:
    drivers/base/regmap/regmap.c:1172:6: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]

Long story short: Jakub Jelinek pointed out that there is a type
mismatch between 'num' in regmap_volatile_range() and 'val_count' in
regmap_raw_read(). And indeed, converting 'num' to the type of
'val_count' (ie, size_t) makes this warning go away.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function regmap_bulk_read() calls the regmap_read() for
each register if set of register has volatile and cache is
enabled. In this case, last few register read makes the memory
corruption if the register size is not the size of unsigned int.
The regam_read() takes argument as unsigned int for returning
value and it update the value as
	*val = map->format.parse_val(map->work_buf);
This causes complete 4 bytes (size of unsigned int) to get written.
Now if client pass the memory pointer for value which is equal to the
required size of register count in regmap_bulk_read() then last few
register read actually update the memory beyond passed pointer size.

Avoid this by using local variable for read and then do memcpy()
for actual byte copy to passed pointer based on register size.

I allocated one pointer ptr and take first 16 bytes dump of that
pointer then call regmap_bulk_read() with pointer which is just
on top of this allocated pointer and register count of 128. Here
register size is 1 byte.
The memory trace of last 5 register read are as follows:

[    5.438589] regmap_bulk_read after regamp_read() for register 122
[    5.447421] 0xef993c20 0xef993c00 0x00000000 0x00000001
[    5.467535] regmap_bulk_read after regamp_read() for register 123
[    5.476374] 0xef993c20 0xef993c00 0x00000000 0x00000001
[    5.496425] regmap_bulk_read after regamp_read() for register 124
[    5.505260] 0xef993c20 0xef993c00 0x00000000 0x00000001
[    5.525372] regmap_bulk_read after regamp_read() for register 125
[    5.534205] 0xef993c00 0xef993c00 0x00000000 0x00000001
[    5.554258] regmap_bulk_read after regamp_read() for register 126
[    5.563100] 0xef990000 0xef993c00 0x00000000 0x00000001
[    5.554258] regmap_bulk_read after regamp_read() for register 127
[    5.587108] 0xef000000 0xef993c00 0x00000000 0x00000001

Here it is observed that the memory content at first word started changing
on last 3 regmap_read() and so corruption happened.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Simple add/add conflict:
	drivers/base/regmap/regmap.c

Resolved simple add/add conflicts:
	drivers/base/regmap/internal.h
	drivers/base/regmap/regmap.c

[Fix for breakage which will be introduced during the merge window via
header reworks in another tree, the regmap tree does include device.h
but Paul's tree breaks that.  Reworded subject to reflect -- broonie]

regmap.s uses devres_alloc() and others that are prototyped in device.h.
Include that to solve the following:

drivers/base/regmap/regmap.c: In function 'devm_regmap_init':
drivers/base/regmap/regmap.c:331:2: error: implicit declaration of function 'devres_alloc' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c:338:3: error: implicit declaration of function 'devres_add' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c:340:3: error: implicit declaration of function 'devres_free' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c: In function '_regmap_raw_write':
drivers/base/regmap/regmap.c:421:5: error: implicit declaration of function 'dev_err' [-Werror=implicit-function-declaration]

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>