[ Upstream commit e7a7681c859643f3f2476b2a28a494877fd89442 ]
When driver uses pm_runtime_force_suspend() as the system suspend callback
function and registers the wake irq with reverse enable ordering, the wake
irq will be re-enabled when entering system suspend, triggering an
'Unbalanced enable for IRQ xxx' warning. In this scenario, the call
sequence during system suspend is as follows:
suspend_devices_and_enter()
-> dpm_suspend_start()
-> dpm_run_callback()
-> pm_runtime_force_suspend()
-> dev_pm_enable_wake_irq_check()
-> dev_pm_enable_wake_irq_complete()
-> suspend_enter()
-> dpm_suspend_noirq()
-> device_wakeup_arm_wake_irqs()
-> dev_pm_arm_wake_irq()
To fix this issue, complete the setting of WAKE_IRQ_DEDICATED_ENABLED flag
in dev_pm_enable_wake_irq_complete() to avoid redundant irq enablement.
Fixes: 8527beb12087 ("PM: sleep: wakeirq: fix wake irq arming")
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Qingliang Li <qingliang.li@mediatek.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 741ba0134fa7822fcf4e4a0a537a5c4cfd706b20 upstream.
The unused clock cleanup uses the _sync initcall to give all users at
earlier initcalls time to probe. Do the same to avoid leaving some PDs
dangling at "on" (which actually happened on qcom!).
Fixes: 2fe71dcdfd10 ("PM / domains: Add late_initcall to disable unused PM domains")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231227-topic-pmdomain_sync_cleanup-v1-1-5f36769d538b@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3ce2cd63e8ee037644db0cbea65e6c40ab6cc178 which is commit aa838896d87af561a33ecefea1caa4c15a68bc47 upstream. Ben writes: When I looked into the referenced security issue, it seemed to only be exploitable through wakelock names, and in the upstream kernel only after commit c8377adfa781 "PM / wakeup: Show wakeup sources stats in sysfs" (first included in 5.4). So I would be interested to know if and why a fix was needed for 4.19. More importantly, this backported version uniformly converts to sysfs_emit(), but there are 3 places sysfs_emit_at() must be used instead: Reported-by: Ben Hutchings <ben@decadent.org.uk> Link: https://lore.kernel.org/r/95831df76c41a53bc3e1ac8ece64915dd63763a1.camel@decadent.org.uk Cc: Joe Perches <joe@perches.com> Cc: Brennan Lamoreaux <blamoreaux@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa838896d87af561a33ecefea1caa4c15a68bc47 upstream.
Convert the various sprintf fmaily calls in sysfs device show functions
to sysfs_emit and sysfs_emit_at for PAGE_SIZE buffer safety.
Done with:
$ spatch -sp-file sysfs_emit_dev.cocci --in-place --max-width=80 .
And cocci script:
$ cat sysfs_emit_dev.cocci
@@
identifier d_show;
identifier dev, attr, buf;
@@
ssize_t d_show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
return
- sprintf(buf,
+ sysfs_emit(buf,
...);
...>
}
@@
identifier d_show;
identifier dev, attr, buf;
@@
ssize_t d_show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
return
- snprintf(buf, PAGE_SIZE,
+ sysfs_emit(buf,
...);
...>
}
@@
identifier d_show;
identifier dev, attr, buf;
@@
ssize_t d_show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
return
- scnprintf(buf, PAGE_SIZE,
+ sysfs_emit(buf,
...);
...>
}
@@
identifier d_show;
identifier dev, attr, buf;
expression chr;
@@
ssize_t d_show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
return
- strcpy(buf, chr);
+ sysfs_emit(buf, chr);
...>
}
@@
identifier d_show;
identifier dev, attr, buf;
identifier len;
@@
ssize_t d_show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
len =
- sprintf(buf,
+ sysfs_emit(buf,
...);
...>
return len;
}
@@
identifier d_show;
identifier dev, attr, buf;
identifier len;
@@
ssize_t d_show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
len =
- snprintf(buf, PAGE_SIZE,
+ sysfs_emit(buf,
...);
...>
return len;
}
@@
identifier d_show;
identifier dev, attr, buf;
identifier len;
@@
ssize_t d_show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
len =
- scnprintf(buf, PAGE_SIZE,
+ sysfs_emit(buf,
...);
...>
return len;
}
@@
identifier d_show;
identifier dev, attr, buf;
identifier len;
@@
ssize_t d_show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
- len += scnprintf(buf + len, PAGE_SIZE - len,
+ len += sysfs_emit_at(buf, len,
...);
...>
return len;
}
@@
identifier d_show;
identifier dev, attr, buf;
expression chr;
@@
ssize_t d_show(struct device *dev, struct device_attribute *attr, char *buf)
{
...
- strcpy(buf, chr);
- return strlen(buf);
+ return sysfs_emit(buf, chr);
}
Signed-off-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/3d033c33056d88bbe34d4ddb62afd05ee166ab9a.1600285923.git.joe@perches.com
[ Brennan : Regenerated for 4.19 to fix CVE-2022-20166 ]
Signed-off-by: Brennan Lamoreaux <blamoreaux@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8527beb12087238d4387607597b4020bc393c4b4 ]
The decision whether to enable a wake irq during suspend can not be done
based on the runtime PM state directly as a driver may use wake irqs
without implementing runtime PM. Such drivers specifically leave the
state set to the default 'suspended' and the wake irq is thus never
enabled at suspend.
Add a new wake irq flag to track whether a dedicated wake irq has been
enabled at runtime suspend and therefore must not be enabled at system
suspend.
Note that pm_runtime_enabled() can not be used as runtime PM is always
disabled during late suspend.
Fixes: 69728051f5bf ("PM / wakeirq: Fix unbalanced IRQ enable for wakeirq")
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 259714100d98b50bf04d36a21bf50ca8b829fc11 ]
When the dedicated wake IRQ is level trigger, and it uses the
device's low-power status as the wakeup source, that means if the
device is not in low-power state, the wake IRQ will be triggered
if enabled; For this case, need enable the wake IRQ after running
the device's ->runtime_suspend() which make it enter low-power state.
e.g.
Assume the wake IRQ is a low level trigger type, and the wakeup
signal comes from the low-power status of the device.
The wakeup signal is low level at running time (0), and becomes
high level when the device enters low-power state (runtime_suspend
(1) is called), a wakeup event at (2) make the device exit low-power
state, then the wakeup signal also becomes low level.
------------------
| ^ ^|
---------------- | | --------------
|<---(0)--->|<--(1)--| (3) (2) (4)
if enable the wake IRQ before running runtime_suspend during (0),
a wake IRQ will arise, it causes resume immediately;
it works if enable wake IRQ ( e.g. at (3) or (4)) after running
->runtime_suspend().
This patch introduces a new status WAKE_IRQ_DEDICATED_REVERSE to
optionally support enabling wake IRQ after running ->runtime_suspend().
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 8527beb12087 ("PM: sleep: wakeirq: fix wake irq arming")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d1c8722083f0332dcd3c85fa1273d85fb6bed8 ]
Currently, while calculating residency and latency values, right
operands may overflow if resulting values are big enough.
To prevent this, albeit unlikely case, play it safe and convert
right operands to left ones' type s64.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 30f604283e05 ("PM / Domains: Allow domain power states to be read from DT")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc80c2e438dcbfcf748452ec0f7ad5b79ff3ad88 ]
Calling __rpm_callback() from rpm_idle() after adding device links
support to the former is a clear mistake.
Not only it causes rpm_idle() to carry out unnecessary actions, but it
is also against the assumption regarding the stability of PM-runtime
status across __rpm_callback() invocations, because rpm_suspend() and
rpm_resume() may run in parallel with __rpm_callback() when it is called
by rpm_idle() and the device's PM-runtime status can be updated by any
of them.
Fixes: 21d5c57b3726 ("PM / runtime: Use device links")
Link: https://lore.kernel.org/linux-pm/36aed941-a73e-d937-2721-4f0decd61ce0@quicinc.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a2bd1b1c64e1ac5627db3767ac465f18606315c ]
When pm_runtime_no_callbacks() has been called for a struct device to set
the dev->power.no_callbacks flag for it, it enables rpm_idle() to take a
slightly quicker path by assuming that a ->runtime_idle() callback would
have returned 0 to indicate success.
A device that does not have the dev->power.no_callbacks flag set for it,
may still be missing a corresponding ->runtime_idle() callback, in which
case the slower path in rpm_idle() is taken. Let's improve the behaviour
for this case, by aligning code to the quicker path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: bc80c2e438dc ("PM: runtime: Do not call __rpm_callback() from rpm_idle()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0c57a5c70c13317238cb19a7ded0eab4a5f7de5 ]
Platforms can provide the information about the availability of each
idle states via status flag. Platforms may have to disable one or more
idle states for various reasons like broken firmware or other unmet
dependencies.
Fix handling of such unavailable/disabled idle states by ignoring them
while parsing the states.
Fixes: a3381e3a65cb ("PM / domains: Fix up domain-idle-states OF parsing")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>