Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The notifier callbacks may want to call some OPP helper routines which
may try to take the same opp_table->lock again and cause a deadlock. One
such usecase was reported by Chanwoo Choi, where calling
dev_pm_opp_disable() leads us to the devfreq's OPP notifier handler,
which further calls dev_pm_opp_find_freq_floor() and it deadlocks.

We don't really need the opp_table->lock to be held across the notifier
call though, all we want to make sure is that the 'opp' doesn't get
freed while being used from within the notifier chain. We can do it with
help of dev_pm_opp_get/put() as well. Let's do it.

Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Fixes: 5b650b388844 "PM / OPP: Take kref from _find_opp_table()"
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

* pm-core:
  PM: core: Fix device_pm_check_callbacks()

* pm-qos:
  PM / QoS: Use the correct variable to check the QoS request type

* pm-docs:
  PM: docs: Drop an excess character from devices.rst
  driver core: Fix link to device power management documentation

The device_pm_check_callbacks() function doesn't check legacy
->suspend and ->resume callback pointers under the device's
bus type, class and driver, so in some cases it may set the
no_pm_callbacks flag for the device incorrectly and then the
callbacks may be skipped during system suspend/resume, which
shouldn't happen.

Fixes: aa8e54b55947 (PM / sleep: Go direct_complete if driver has no callbacks)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 4.5+ <stable@vger.kernel.org> # 4.5+

Use the actual function argument for the validation of the request type,
instead of the type field in a fresh (supposedly zero-initialized)
request structure.

Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

* pm-sleep:
  ACPI / PM: Check low power idle constraints for debug only
  PM / s2idle: Rename platform operations structure
  PM / s2idle: Rename ->enter_freeze to ->enter_s2idle
  PM / s2idle: Rename freeze_state enum and related items
  PM / s2idle: Rename PM_SUSPEND_FREEZE to PM_SUSPEND_TO_IDLE
  ACPI / PM: Prefer suspend-to-idle over S3 on some systems
  platform/x86: intel-hid: Wake up Dell Latitude 7275 from suspend-to-idle
  PM / suspend: Define pr_fmt() in suspend.c
  PM / suspend: Use mem_sleep_labels[] strings in messages
  PM / sleep: Put pm_test under CONFIG_PM_SLEEP_DEBUG
  PM / sleep: Check pm_wakeup_pending() in __device_suspend_noirq()
  PM / core: Add error argument to dpm_show_time()
  PM / core: Split dpm_suspend_noirq() and dpm_resume_noirq()
  PM / s2idle: Rearrange the main suspend-to-idle loop
  PM / timekeeping: Print debug messages when requested
  PM / sleep: Mark suspend/hibernation start and finish
  PM / sleep: Do not print debug messages by default
  PM / suspend: Export pm_suspend_target_state

* pm-core:
  PM / wakeup: Set power.can_wakeup if wakeup_sysfs_add() fails

* pm-opp:
  PM / OPP: Fix get sharing CPUs when hotplug is used
  PM / OPP: OF: Use pr_debug() instead of pr_err() while adding OPP table

* pm-domains:
  PM / Domains: Convert to using %pOF instead of full_name
  PM / Domains: Extend generic power domain debugfs
  PM / Domains: Add time accounting to various genpd states

* pm-cpu:
  PM / CPU: replace raw_notifier with atomic_notifier

* pm-avs:
  PM / AVS: rockchip-io: add io selectors and supplies for RV1108

Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Rename the freeze_state enum representing the suspend-to-idle state
machine states to s2idle_states and rename the related variables and
functions accordingly.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently, an error from wakeup_sysfs_add() in
device_set_wakeup_capable() causes the device's power.can_wakeup
flag to remain unset even though the device technically is capable
of signaling wakeup.

If wakeup_sysfs_add() fails user space may not be able to enable
the device to wake up the system from sleep states, but at least
for some devices that does not matter.

For this reason, set or clear power.can_wakeup upfront and if
wakeup_sysfs_add() returns an error, print a message to the log.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>