linux-stable.git/drivers/ata, branch v6.5.6

ata: libata-core: Do not register PM operations for SAS ports

2023-10-06T11:16:28+00:00

commit 75e2bd5f1ede42a2bc88aa34b431e1ace8e0bea0 upstream.

libsas does its own domain based power management of ports. For such
ports, libata should not use a device type defining power management
operations as executing these operations for suspend/resume in addition
to libsas calls to ata_sas_port_suspend() and ata_sas_port_resume() is
not necessary (and likely dangerous to do, even though problems are not
seen currently).

Introduce the new ata_port_sas_type device_type for ports managed by
libsas. This new device type is used in ata_tport_add() and is defined
without power management operations.

Fixes: 2fcbdcb4c802 ("[SCSI] libata: export ata_port suspend/resume infrastructure for sas")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal 
Reviewed-by: Hannes Reinecke 
Tested-by: Chia-Lin Kao (AceLan) 
Tested-by: Geert Uytterhoeven 
Reviewed-by: John Garry 
Reviewed-by: Martin K. Petersen 
Signed-off-by: Greg Kroah-Hartman

ata: libata-core: Fix port and device removal

2023-10-06T11:16:28+00:00

commit 84d76529c650f887f1e18caee72d6f0589e1baf9 upstream.

Whenever an ATA adapter driver is removed (e.g. rmmod),
ata_port_detach() is called repeatedly for all the adapter ports to
remove (unload) the devices attached to the port and delete the port
device itself. Removing of devices is done using libata EH with the
ATA_PFLAG_UNLOADING port flag set. This causes libata EH to execute
ata_eh_unload() which disables all devices attached to the port.

ata_port_detach() finishes by calling scsi_remove_host() to remove the
scsi host associated with the port. This function will trigger the
removal of all scsi devices attached to the host and in the case of
disks, calls to sd_shutdown() which will flush the device write cache
and stop the device. However, given that the devices were already
disabled by ata_eh_unload(), the synchronize write cache command and
start stop unit commands fail. E.g. running "rmmod ahci" with first
removing sd_mod results in error messages like:

ata13.00: disable device
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 0:0:0:0: [sda] Stopping disk
sd 0:0:0:0: [sda] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK

Fix this by removing all scsi devices of the ata devices connected to
the port before scheduling libata EH to disable the ATA devices.

Fixes: 720ba12620ee ("[PATCH] libata-hp: update unload-unplug")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal 
Reviewed-by: Hannes Reinecke 
Reviewed-by: Niklas Cassel 
Tested-by: Chia-Lin Kao (AceLan) 
Tested-by: Geert Uytterhoeven 
Reviewed-by: Martin K. Petersen 
Signed-off-by: Greg Kroah-Hartman

ata: libata-core: Fix ata_port_request_pm() locking

2023-10-06T11:16:28+00:00

commit 3b8e0af4a7a331d1510e963b8fd77e2fca0a77f1 upstream.

The function ata_port_request_pm() checks the port flag
ATA_PFLAG_PM_PENDING and calls ata_port_wait_eh() if this flag is set to
ensure that power management operations for a port are not scheduled
simultaneously. However, this flag check is done without holding the
port lock.

Fix this by taking the port lock on entry to the function and checking
the flag under this lock. The lock is released and re-taken if
ata_port_wait_eh() needs to be called. The two WARN_ON() macros checking
that the ATA_PFLAG_PM_PENDING flag was cleared are removed as the first
call is racy and the second one done without holding the port lock.

Fixes: 5ef41082912b ("ata: add ata port system PM callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal 
Reviewed-by: Hannes Reinecke 
Tested-by: Chia-Lin Kao (AceLan) 
Reviewed-by: Niklas Cassel 
Tested-by: Geert Uytterhoeven 
Reviewed-by: Martin K. Petersen 
Reviewed-by: Bart Van Assche 
Signed-off-by: Greg Kroah-Hartman

ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES

2023-10-06T11:16:23+00:00

commit 3ef600923521616ebe192c893468ad0424de2afb upstream.

For REPORT SUPPORTED OPERATION CODES command, the service action field is
defined as bits 0-4 in the second byte in the CDB. Bits 5-7 in the second
byte are reserved.

Only look at the service action field in the second byte when determining
if the MAINTENANCE IN opcode is a REPORT SUPPORTED OPERATION CODES command.

This matches how we only look at the service action field in the second
byte when determining if the SERVICE ACTION IN(16) opcode is a READ
CAPACITY(16) command (reserved bits 5-7 in the second byte are ignored).

Fixes: 7b2030942859 ("libata: Add support for SCT Write Same")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Cassel 
Signed-off-by: Damien Le Moal 
Signed-off-by: Greg Kroah-Hartman

scsi: sd: Differentiate system and runtime start/stop management

2023-10-06T11:16:22+00:00

commit 3cc2ffe5c16dc65dfac354bc5b5bc98d3b397567 upstream.

The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.

For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.

Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.

Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal 
Reviewed-by: Hannes Reinecke 
Tested-by: Geert Uytterhoeven 
Reviewed-by: Martin K. Petersen 
Signed-off-by: Greg Kroah-Hartman

ata: libata-scsi: link ata port and scsi device

2023-10-06T11:16:22+00:00

commit fb99ef17865035a6657786d4b2af11a27ba23f9b upstream.

There is no direct device ancestry defined between an ata_device and
its scsi device which prevents the power management code from correctly
ordering suspend and resume operations. Create such ancestry with the
ata device as the parent to ensure that the scsi device (child) is
suspended before the ata device and that resume handles the ata device
before the scsi device.

The parent-child (supplier-consumer) relationship is established between
the ata_port (parent) and the scsi device (child) with the function
device_add_link(). The parent used is not the ata_device as the PM
operations are defined per port and the status of all devices connected
through that port is controlled from the port operations.

The device link is established with the new function
ata_scsi_slave_alloc(), and this function is used to define the
->slave_alloc callback of the scsi host template of all ata drivers.

Fixes: a19a93e4c6a9 ("scsi: core: pm: Rely on the device driver core for async power management")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal 
Reviewed-by: Hannes Reinecke 
Reviewed-by: Niklas Cassel 
Tested-by: Geert Uytterhoeven 
Reviewed-by: Martin K. Petersen 
Reviewed-by: John Garry 
Signed-off-by: Greg Kroah-Hartman

scsi: core: ata: Do no try to probe for CDL on old drives

2023-10-06T11:16:21+00:00

commit 2132df16f53b4f01ab25f5d404f36a22244ae342 upstream.

Some old drives (e.g. an Ultra320 SCSI disk as reported by John) do not
seem to execute MAINTENANCE_IN / MI_REPORT_SUPPORTED_OPERATION_CODES
commands correctly and hang when a non-zero service action is specified
(one command format with service action case in scsi_report_opcode()).

Currently, CDL probing with scsi_cdl_check_cmd() is the only caller using a
non zero service action for scsi_report_opcode(). To avoid issues with
these old drives, do not attempt CDL probe if the device reports support
for an SPC version lower than 5 (CDL was introduced in SPC-5). To keep
things working with ATA devices which probe for the CDL T2A and T2B pages
introduced with SPC-6, modify ata_scsiop_inq_std() to claim SPC-6 version
compatibility for ATA drives supporting CDL.

SPC-6 standard version number is defined as Dh (= 13) in SPC-6 r09. Fix
scsi_probe_lun() to correctly capture this value by changing the bit mask
for the second byte of the INQUIRY response from 0x7 to 0xf.
include/scsi/scsi.h is modified to add the definition SCSI_SPC_6 with the
value 14 (Dh + 1). The missing definitions for the SCSI_SPC_4 and
SCSI_SPC_5 versions are also added.

Reported-by: John David Anglin 
Fixes: 624885209f31 ("scsi: core: Detect support for command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal 
Link: https://lore.kernel.org/r/20230915022034.678121-1-dlemoal@kernel.org
Tested-by: David Gow 
Reviewed-by: Bart Van Assche 
Reviewed-by: Niklas Cassel 
Signed-off-by: Martin K. Petersen 
Signed-off-by: Greg Kroah-Hartman

ata: libata-eh: do not thaw the port twice in ata_eh_reset()

2023-10-06T11:16:13+00:00

[ Upstream commit 7a3bc2b3989e05bbaa904a63279049a401491c84 ]

commit 1e641060c4b5 ("libata: clear eh_info on reset completion") added
a workaround that broke the retry mechanism in ATA EH.

Tejun himself suggested to remove this workaround when it was identified
to cause additional problems:
https://lore.kernel.org/linux-ide/20110426135027.GI878@htj.dyndns.org/

He even said:
"Hmm... it seems I wasn't thinking straight when I added that work around."
https://lore.kernel.org/linux-ide/20110426155229.GM878@htj.dyndns.org/

While removing the workaround solved the issue, however, the workaround was
kept to avoid "spurious hotplug events during reset", and instead another
workaround was added on top of the existing workaround in commit
8c56cacc724c ("libata: fix unexpectedly frozen port after ata_eh_reset()").

Because these IRQs happened when the port was frozen, we know that they
were actually a side effect of PxIS and IS.IPS(x) not being cleared before
the COMRESET. This is now done in commit 94152042eaa9 ("ata: libahci: clear
pending interrupt status"), so these workarounds can now be removed.

Since commit 1e641060c4b5 ("libata: clear eh_info on reset completion") has
now been reverted, the ATA EH retry mechanism is functional again, so there
is once again no need to thaw the port more than once in ata_eh_reset().

This reverts "the workaround on top of the workaround" introduced in commit
8c56cacc724c ("libata: fix unexpectedly frozen port after ata_eh_reset()").

Signed-off-by: Niklas Cassel 
Signed-off-by: Damien Le Moal 
Signed-off-by: Sasha Levin

ata: libata-eh: do not clear ATA_PFLAG_EH_PENDING in ata_eh_reset()

2023-10-06T11:16:13+00:00

[ Upstream commit 80cc944eca4f0baa9c381d0706f3160e491437f2 ]

ata_scsi_port_error_handler() starts off by clearing ATA_PFLAG_EH_PENDING,
before calling ap->ops->error_handler() (without holding the ap->lock).

If an error IRQ is received while ap->ops->error_handler() is running,
the irq handler will set ATA_PFLAG_EH_PENDING.

Once ap->ops->error_handler() returns, ata_scsi_port_error_handler()
checks if ATA_PFLAG_EH_PENDING is set, and if it is, another iteration
of ATA EH is performed.

The problem is that ATA_PFLAG_EH_PENDING is not only cleared by
ata_scsi_port_error_handler(), it is also cleared by ata_eh_reset().

ata_eh_reset() is called by ap->ops->error_handler(). This additional
clearing done by ata_eh_reset() breaks the whole retry logic in
ata_scsi_port_error_handler(). Thus, if an error IRQ is received while
ap->ops->error_handler() is running, the port will currently remain
frozen and will never get re-enabled.

The additional clearing in ata_eh_reset() was introduced in commit
1e641060c4b5 ("libata: clear eh_info on reset completion").

Looking at the original error report:
https://marc.info/?l=linux-ide&m=124765325828495&w=2

We can see the following happening:
[    1.074659] ata3: XXX port freeze
[    1.074700] ata3: XXX hardresetting link, stopping engine
[    1.074746] ata3: XXX flipping SControl

[    1.411471] ata3: XXX irq_stat=400040 CONN|PHY
[    1.411475] ata3: XXX port freeze

[    1.420049] ata3: XXX starting engine
[    1.420096] ata3: XXX rc=0, class=1
[    1.420142] ata3: XXX clearing IRQs for thawing
[    1.420188] ata3: XXX port thawed
[    1.420234] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

We are not supposed to be able to receive an error IRQ while the port is
frozen (PxIE is set to 0, i.e. all IRQs for the port are disabled).

AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) states:
"Each bit location can be thought of as reporting a '1' if the virtual
"interrupt line" for that port is indicating it wishes to generate an
interrupt. That is, if a port has one or more interrupt status bit set,
and the enables for those status bits are set, then this bit shall be set."

Additionally, AHCI state P:ComInit clearly shows that the state machine
will only jump to P:ComInitSetIS (which sets IS.IPS(x) to '1'), if PxIE.PCE
is set to '1'. In our case, PxIE is set to 0, so IS.IPS(x) won't get set.

So IS.IPS(x) only gets set if PxIS and PxIE is set.

AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) also states:
"The bits in this register are read/write clear. It is set by the level of
the virtual interrupt line being a set, and cleared by a write of '1' from
the software."

So if IS.IPS(x) is set, you need to explicitly clear it by writing a 1 to
IS.IPS(x) for that port.

Since PxIE is cleared, the only way to get an interrupt while the port is
frozen, is if IS.IPS(x) is set, and the only way IS.IPS(x) can be set when
the port is frozen, is if it was set before the port was frozen.

However, since commit 737dd811a3db ("ata: libahci: clear pending interrupt
status"), we clear both PxIS and IS.IPS(x) after freezing the port, but
before the COMRESET, so the problem that commit 1e641060c4b5 ("libata:
clear eh_info on reset completion") fixed can no longer happen.

Thus, revert commit 1e641060c4b5 ("libata: clear eh_info on reset
completion"), so that the retry logic in ata_scsi_port_error_handler()
works once again. (The retry logic is still needed, since we can still
get an error IRQ _after_ the port has been thawed, but before
ata_scsi_port_error_handler() takes the ap->lock in order to check
if ATA_PFLAG_EH_PENDING is set.)

Signed-off-by: Niklas Cassel 
Signed-off-by: Damien Le Moal 
Signed-off-by: Sasha Levin

ata: sata_mv: Fix incorrect string length computation in mv_dump_mem()

2023-10-06T11:16:10+00:00

[ Upstream commit e97eb65dd464e7f118a16a26337322d07eb653e2 ]

snprintf() returns the "number of characters which *would* be generated for
the given input", not the size *really* generated.

In order to avoid too large values for 'o' (and potential negative values
for "sizeof(linebuf) o") use scnprintf() instead of snprintf().

Note that given the "w < 4" in the for loop, the buffer can NOT
overflow, but using the *right* function is always better.

Signed-off-by: Christophe JAILLET 
Signed-off-by: Damien Le Moal 
Signed-off-by: Sasha Levin