linux-stable.git/drivers/ata, branch v6.0.7 Linux kernel stable tree ata: ahci: Match EM_MAX_SLOTS with SATA_PMP_MAX_PORTS 2022-10-29T08:08:30+00:00 Kai-Heng Feng kai.heng.feng@canonical.com 2022-10-11T02:46:17+00:00 d6314d5f68764550c84d732ce901ddd3ac6b415f commit 1e41e693f458eef2d5728207dbd327cd3b16580a upstream. UBSAN complains about array-index-out-of-bounds: [ 1.980703] kernel: UBSAN: array-index-out-of-bounds in /build/linux-9H675w/linux-5.15.0/drivers/ata/libahci.c:968:41 [ 1.980709] kernel: index 15 is out of range for type 'ahci_em_priv [8]' [ 1.980713] kernel: CPU: 0 PID: 209 Comm: scsi_eh_8 Not tainted 5.15.0-25-generic #25-Ubuntu [ 1.980716] kernel: Hardware name: System manufacturer System Product Name/P5Q3, BIOS 1102 06/11/2010 [ 1.980718] kernel: Call Trace: [ 1.980721] kernel: <TASK> [ 1.980723] kernel: show_stack+0x52/0x58 [ 1.980729] kernel: dump_stack_lvl+0x4a/0x5f [ 1.980734] kernel: dump_stack+0x10/0x12 [ 1.980736] kernel: ubsan_epilogue+0x9/0x45 [ 1.980739] kernel: __ubsan_handle_out_of_bounds.cold+0x44/0x49 [ 1.980742] kernel: ahci_qc_issue+0x166/0x170 [libahci] [ 1.980748] kernel: ata_qc_issue+0x135/0x240 [ 1.980752] kernel: ata_exec_internal_sg+0x2c4/0x580 [ 1.980754] kernel: ? vprintk_default+0x1d/0x20 [ 1.980759] kernel: ata_exec_internal+0x67/0xa0 [ 1.980762] kernel: sata_pmp_read+0x8d/0xc0 [ 1.980765] kernel: sata_pmp_read_gscr+0x3c/0x90 [ 1.980768] kernel: sata_pmp_attach+0x8b/0x310 [ 1.980771] kernel: ata_eh_revalidate_and_attach+0x28c/0x4b0 [ 1.980775] kernel: ata_eh_recover+0x6b6/0xb30 [ 1.980778] kernel: ? ahci_do_hardreset+0x180/0x180 [libahci] [ 1.980783] kernel: ? ahci_stop_engine+0xb0/0xb0 [libahci] [ 1.980787] kernel: ? ahci_do_softreset+0x290/0x290 [libahci] [ 1.980792] kernel: ? trace_event_raw_event_ata_eh_link_autopsy_qc+0xe0/0xe0 [ 1.980795] kernel: sata_pmp_eh_recover.isra.0+0x214/0x560 [ 1.980799] kernel: sata_pmp_error_handler+0x23/0x40 [ 1.980802] kernel: ahci_error_handler+0x43/0x80 [libahci] [ 1.980806] kernel: ata_scsi_port_error_handler+0x2b1/0x600 [ 1.980810] kernel: ata_scsi_error+0x9c/0xd0 [ 1.980813] kernel: scsi_error_handler+0xa1/0x180 [ 1.980817] kernel: ? scsi_unjam_host+0x1c0/0x1c0 [ 1.980820] kernel: kthread+0x12a/0x150 [ 1.980823] kernel: ? set_kthread_struct+0x50/0x50 [ 1.980826] kernel: ret_from_fork+0x22/0x30 [ 1.980831] kernel: </TASK> This happens because sata_pmp_init_links() initialize link->pmp up to SATA_PMP_MAX_PORTS while em_priv is declared as 8 elements array. I can't find the maximum Enclosure Management ports specified in AHCI spec v1.3.1, but "12.2.1 LED message type" states that "Port Multiplier Information" can utilize 4 bits, which implies it can support up to 16 ports. Hence, use SATA_PMP_MAX_PORTS as EM_MAX_SLOTS to resolve the issue. BugLink: https://bugs.launchpad.net/bugs/1970074 Cc: stable@vger.kernel.org Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1e41e693f458eef2d5728207dbd327cd3b16580a upstream.

UBSAN complains about array-index-out-of-bounds:
[ 1.980703] kernel: UBSAN: array-index-out-of-bounds in /build/linux-9H675w/linux-5.15.0/drivers/ata/libahci.c:968:41
[ 1.980709] kernel: index 15 is out of range for type 'ahci_em_priv [8]'
[ 1.980713] kernel: CPU: 0 PID: 209 Comm: scsi_eh_8 Not tainted 5.15.0-25-generic #25-Ubuntu
[ 1.980716] kernel: Hardware name: System manufacturer System Product Name/P5Q3, BIOS 1102 06/11/2010
[ 1.980718] kernel: Call Trace:
[ 1.980721] kernel: <TASK>
[ 1.980723] kernel: show_stack+0x52/0x58
[ 1.980729] kernel: dump_stack_lvl+0x4a/0x5f
[ 1.980734] kernel: dump_stack+0x10/0x12
[ 1.980736] kernel: ubsan_epilogue+0x9/0x45
[ 1.980739] kernel: __ubsan_handle_out_of_bounds.cold+0x44/0x49
[ 1.980742] kernel: ahci_qc_issue+0x166/0x170 [libahci]
[ 1.980748] kernel: ata_qc_issue+0x135/0x240
[ 1.980752] kernel: ata_exec_internal_sg+0x2c4/0x580
[ 1.980754] kernel: ? vprintk_default+0x1d/0x20
[ 1.980759] kernel: ata_exec_internal+0x67/0xa0
[ 1.980762] kernel: sata_pmp_read+0x8d/0xc0
[ 1.980765] kernel: sata_pmp_read_gscr+0x3c/0x90
[ 1.980768] kernel: sata_pmp_attach+0x8b/0x310
[ 1.980771] kernel: ata_eh_revalidate_and_attach+0x28c/0x4b0
[ 1.980775] kernel: ata_eh_recover+0x6b6/0xb30
[ 1.980778] kernel: ? ahci_do_hardreset+0x180/0x180 [libahci]
[ 1.980783] kernel: ? ahci_stop_engine+0xb0/0xb0 [libahci]
[ 1.980787] kernel: ? ahci_do_softreset+0x290/0x290 [libahci]
[ 1.980792] kernel: ? trace_event_raw_event_ata_eh_link_autopsy_qc+0xe0/0xe0
[ 1.980795] kernel: sata_pmp_eh_recover.isra.0+0x214/0x560
[ 1.980799] kernel: sata_pmp_error_handler+0x23/0x40
[ 1.980802] kernel: ahci_error_handler+0x43/0x80 [libahci]
[ 1.980806] kernel: ata_scsi_port_error_handler+0x2b1/0x600
[ 1.980810] kernel: ata_scsi_error+0x9c/0xd0
[ 1.980813] kernel: scsi_error_handler+0xa1/0x180
[ 1.980817] kernel: ? scsi_unjam_host+0x1c0/0x1c0
[ 1.980820] kernel: kthread+0x12a/0x150
[ 1.980823] kernel: ? set_kthread_struct+0x50/0x50
[ 1.980826] kernel: ret_from_fork+0x22/0x30
[ 1.980831] kernel: </TASK>

This happens because sata_pmp_init_links() initialize link->pmp up to
SATA_PMP_MAX_PORTS while em_priv is declared as 8 elements array.

I can't find the maximum Enclosure Management ports specified in AHCI
spec v1.3.1, but "12.2.1 LED message type" states that "Port Multiplier
Information" can utilize 4 bits, which implies it can support up to 16
ports. Hence, use SATA_PMP_MAX_PORTS as EM_MAX_SLOTS to resolve the
issue.

BugLink: https://bugs.launchpad.net/bugs/1970074
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ata: ahci-imx: Fix MODULE_ALIAS 2022-10-29T08:08:30+00:00 Alexander Stein alexander.stein@ew.tq-group.com 2022-10-12T13:11:05+00:00 91a0eac09b9e6624b0263f7c87482c31044a6c86 commit 979556f1521a835a059de3b117b9c6c6642c7d58 upstream. 'ahci:' is an invalid prefix, preventing the module from autoloading. Fix this by using the 'platform:' prefix and DRV_NAME. Fixes: 9e54eae23bc9 ("ahci_imx: add ahci sata support on imx platforms") Cc: stable@vger.kernel.org Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 979556f1521a835a059de3b117b9c6c6642c7d58 upstream.

'ahci:' is an invalid prefix, preventing the module from autoloading.
Fix this by using the 'platform:' prefix and DRV_NAME.

Fixes: 9e54eae23bc9 ("ahci_imx: add ahci sata support on imx platforms")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ata: libahci_platform: Sanity check the DT child nodes number 2022-10-21T10:39:22+00:00 Serge Semin Sergey.Semin@baikalelectronics.ru 2022-09-09T19:36:06+00:00 a15016c29e532d1e220de9cccf2cd2242415e851 [ Upstream commit 3c132ea6508b34956e5ed88d04936983ec230601 ] Having greater than AHCI_MAX_PORTS (32) ports detected isn't that critical from the further AHCI-platform initialization point of view since exceeding the ports upper limit will cause allocating more resources than will be used afterwards. But detecting too many child DT-nodes doesn't seem right since it's very unlikely to have it on an ordinary platform. In accordance with the AHCI specification there can't be more than 32 ports implemented at least due to having the CAP.NP field of 5 bits wide and the PI register of dword size. Thus if such situation is found the DTB must have been corrupted and the data read from it shouldn't be reliable. Let's consider that as an erroneous situation and halt further resources allocation. Note it's logically more correct to have the nports set only after the initialization value is checked for being sane. So while at it let's make sure nports is assigned with a correct value. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 3c132ea6508b34956e5ed88d04936983ec230601 ]

Having greater than AHCI_MAX_PORTS (32) ports detected isn't that critical
from the further AHCI-platform initialization point of view since
exceeding the ports upper limit will cause allocating more resources than
will be used afterwards. But detecting too many child DT-nodes doesn't
seem right since it's very unlikely to have it on an ordinary platform. In
accordance with the AHCI specification there can't be more than 32 ports
implemented at least due to having the CAP.NP field of 5 bits wide and the
PI register of dword size. Thus if such situation is found the DTB must
have been corrupted and the data read from it shouldn't be reliable. Let's
consider that as an erroneous situation and halt further resources
allocation.

Note it's logically more correct to have the nports set only after the
initialization value is checked for being sane. So while at it let's make
sure nports is assigned with a correct value.

Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ata: libata-sata: Fix device queue depth control 2022-09-28T11:47:31+00:00 Damien Le Moal damien.lemoal@opensource.wdc.com 2022-09-24T06:18:26+00:00 141f3d6256e58103ece1c3dd2835e871f1dde240 The function __ata_change_queue_depth() uses the helper ata_scsi_find_dev() to get the ata_device structure of a scsi device and set that device maximum queue depth. However, when the ata device is managed by libsas, ata_scsi_find_dev() returns NULL, turning __ata_change_queue_depth() into a nop, which prevents the user from setting the maximum queue depth of ATA devices used with libsas based HBAs. Fix this by renaming __ata_change_queue_depth() to ata_change_queue_depth() and adding a pointer to the ata_device structure of the target device as argument. This pointer is provided by ata_scsi_change_queue_depth() using ata_scsi_find_dev() in the case of a libata managed device and by sas_change_queue_depth() using sas_to_ata_dev() in the case of a libsas managed ata device. Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Tested-by: John Garry <john.garry@huawei.com> 
The function __ata_change_queue_depth() uses the helper
ata_scsi_find_dev() to get the ata_device structure of a scsi device and
set that device maximum queue depth. However, when the ata device is
managed by libsas, ata_scsi_find_dev() returns NULL, turning
__ata_change_queue_depth() into a nop, which prevents the user from
setting the maximum queue depth of ATA devices used with libsas based
HBAs.

Fix this by renaming __ata_change_queue_depth() to
ata_change_queue_depth() and adding a pointer to the ata_device
structure of the target device as argument. This pointer is provided by
ata_scsi_change_queue_depth() using ata_scsi_find_dev() in the case of
a libata managed device and by sas_change_queue_depth() using
sas_to_ata_dev() in the case of a libsas managed ata device.

Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: John Garry <john.garry@huawei.com>
ata: libata-scsi: Fix initialization of device queue depth 2022-09-28T11:47:26+00:00 Damien Le Moal damien.lemoal@opensource.wdc.com 2022-09-24T05:44:11+00:00 6a8438de524346f2ac73b0b493980c336ebce688 For SATA devices supporting NCQ, drivers using libsas first initialize a scsi device queue depth based on the controller and device capabilities, leading to the scsi device queue_depth field being 32 (ATA maximum queue depth) for most setup. However, if libata was loaded using the force=[ID]]noncq argument, the default queue depth should be set to 1 to reflect the fact that queuable commands will never be used. This is consistent with manually setting a device queue depth to 1 through sysfs as that disables NCQ use for the device. Fix ata_scsi_dev_config() to honor the noncq parameter by sertting the device queue depth to 1 for devices that do not have the ATA_DFLAG_NCQ flag set. Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Tested-by: John Garry <john.garry@huawei.com> 
For SATA devices supporting NCQ, drivers using libsas first initialize a
scsi device queue depth based on the controller and device capabilities,
leading to the scsi device queue_depth field being 32 (ATA maximum queue
depth) for most setup. However, if libata was loaded using the
force=[ID]]noncq argument, the default queue depth should be set to 1 to
reflect the fact that queuable commands will never be used. This is
consistent with manually setting a device queue depth to 1 through sysfs
as that disables NCQ use for the device.

Fix ata_scsi_dev_config() to honor the noncq parameter by sertting the
device queue depth to 1 for devices that do not have the ATA_DFLAG_NCQ
flag set.

Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: John Garry <john.garry@huawei.com>
libata: add ATA_HORKAGE_NOLPM for Pioneer BDR-207M and BDR-205 2022-09-26T23:20:37+00:00 Niklas Cassel niklas.cassel@wdc.com 2022-09-26T18:38:09+00:00 ea08aec7e77bfd6599489ec430f9f859ab84575a Commit 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile") added an explicit entry for AMD Green Sardine AHCI controller using the board_ahci_mobile configuration (this configuration has later been renamed to board_ahci_low_power). The board_ahci_low_power configuration enables support for low power modes. This explicit entry takes precedence over the generic AHCI controller entry, which does not enable support for low power modes. Therefore, when commit 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile") was backported to stable kernels, it make some Pioneer optical drives, which was working perfectly fine before the commit was backported, stop working. The real problem is that the Pioneer optical drives do not handle low power modes correctly. If these optical drives would have been tested on another AHCI controller using the board_ahci_low_power configuration, this issue would have been detected earlier. Unfortunately, the board_ahci_low_power configuration is only used in less than 15% of the total AHCI controller entries, so many devices have never been tested with an AHCI controller with low power modes. Fixes: 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile") Cc: stable@vger.kernel.org Reported-by: Jaap Berkhout <j.j.berkhout@staalenberk.nl> Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> 
Commit 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as
board_ahci_mobile") added an explicit entry for AMD Green Sardine
AHCI controller using the board_ahci_mobile configuration (this
configuration has later been renamed to board_ahci_low_power).

The board_ahci_low_power configuration enables support for low power
modes.

This explicit entry takes precedence over the generic AHCI controller
entry, which does not enable support for low power modes.

Therefore, when commit 1527f69204fe ("ata: ahci: Add Green Sardine
vendor ID as board_ahci_mobile") was backported to stable kernels,
it make some Pioneer optical drives, which was working perfectly fine
before the commit was backported, stop working.

The real problem is that the Pioneer optical drives do not handle low
power modes correctly. If these optical drives would have been tested
on another AHCI controller using the board_ahci_low_power configuration,
this issue would have been detected earlier.

Unfortunately, the board_ahci_low_power configuration is only used in
less than 15% of the total AHCI controller entries, so many devices
have never been tested with an AHCI controller with low power modes.

Fixes: 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile")
Cc: stable@vger.kernel.org
Reported-by: Jaap Berkhout <j.j.berkhout@staalenberk.nl>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
ata: libata-eh: Add missing command name 2022-08-15T20:42:51+00:00 Damien Le Moal damien.lemoal@opensource.wdc.com 2022-08-11T17:29:53+00:00 d3122bf9aa4c974f5e2c0112f799757b3a2779da Add the missing command name for ATA_CMD_NCQ_NON_DATA to ata_get_cmd_name(). Fixes: 661ce1f0c4a6 ("libata/libsas: Define ATA_CMD_NCQ_NON_DATA") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Hannes Reinecke <hare@suse.de> 
Add the missing command name for ATA_CMD_NCQ_NON_DATA to
ata_get_cmd_name().

Fixes: 661ce1f0c4a6 ("libata/libsas: Define ATA_CMD_NCQ_NON_DATA")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Merge tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux 2022-08-06T23:38:17+00:00 Linus Torvalds torvalds@linux-foundation.org 2022-08-06T23:38:17+00:00 cae4199f9319f42534ee2e2e4aadf183b9bb7f73 Pull powerpc updates from Michael Ellerman: - Add support for syscall stack randomization - Add support for atomic operations to the 32 & 64-bit BPF JIT - Full support for KASAN on 64-bit Book3E - Add a watchdog driver for the new PowerVM hypervisor watchdog - Add a number of new selftests for the Power10 PMU support - Add a driver for the PowerVM Platform KeyStore - Increase the NMI watchdog timeout during live partition migration, to avoid timeouts due to increased memory access latency - Add support for using the 'linux,pci-domain' device tree property for PCI domain assignment - Many other small features and fixes Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A. Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada, Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch, Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár, Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu Jianfeng, and Zhouyi Zhou. * tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits) powerpc/64e: Fix kexec build error EDAC/ppc_4xx: Include required of_irq header directly powerpc/pci: Fix PHB numbering when using opal-phbid powerpc/64: Init jump labels before parse_early_param() selftests/powerpc: Avoid GCC 12 uninitialised variable warning powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address powerpc/xive: Fix refcount leak in xive_get_max_prio powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader powerpc/perf: Include caps feature for power10 DD1 version powerpc: add support for syscall stack randomization powerpc: Move system_call_exception() to syscall.c powerpc/powernv: rename remaining rng powernv_ functions to pnv_ powerpc/powernv/kvm: Use darn for H_RANDOM on Power9 powerpc/powernv: Avoid crashing if rng is NULL selftests/powerpc: Fix matrix multiply assist test powerpc/signal: Update comment for clarity powerpc: make facility_unavailable_exception 64s powerpc/platforms/83xx/suspend: Remove write-only global variable powerpc/platforms/83xx/suspend: Prevent unloading the driver powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration ... 
Pull powerpc updates from Michael Ellerman:

 - Add support for syscall stack randomization

 - Add support for atomic operations to the 32 & 64-bit BPF JIT

 - Full support for KASAN on 64-bit Book3E

 - Add a watchdog driver for the new PowerVM hypervisor watchdog

 - Add a number of new selftests for the Power10 PMU support

 - Add a driver for the PowerVM Platform KeyStore

 - Increase the NMI watchdog timeout during live partition migration, to
   avoid timeouts due to increased memory access latency

 - Add support for using the 'linux,pci-domain' device tree property for
   PCI domain assignment

 - Many other small features and fixes

Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N.  Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.

* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
  powerpc/64e: Fix kexec build error
  EDAC/ppc_4xx: Include required of_irq header directly
  powerpc/pci: Fix PHB numbering when using opal-phbid
  powerpc/64: Init jump labels before parse_early_param()
  selftests/powerpc: Avoid GCC 12 uninitialised variable warning
  powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
  powerpc/xive: Fix refcount leak in xive_get_max_prio
  powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
  powerpc/perf: Include caps feature for power10 DD1 version
  powerpc: add support for syscall stack randomization
  powerpc: Move system_call_exception() to syscall.c
  powerpc/powernv: rename remaining rng powernv_ functions to pnv_
  powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
  powerpc/powernv: Avoid crashing if rng is NULL
  selftests/powerpc: Fix matrix multiply assist test
  powerpc/signal: Update comment for clarity
  powerpc: make facility_unavailable_exception 64s
  powerpc/platforms/83xx/suspend: Remove write-only global variable
  powerpc/platforms/83xx/suspend: Prevent unloading the driver
  powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
  ...
Merge tag 'dma-mapping-5.20-2022-08-06' of git://git.infradead.org/users/hch/dma-mapping 2022-08-06T17:56:45+00:00 Linus Torvalds torvalds@linux-foundation.org 2022-08-06T17:56:45+00:00 c993e07be023acdeec8e84e2e0743c52adb5fc94 Pull dma-mapping updates from Christoph Hellwig: - convert arm32 to the common dma-direct code (Arnd Bergmann, Robin Murphy, Christoph Hellwig) - restructure the PCIe peer to peer mapping support (Logan Gunthorpe) - allow the IOMMU code to communicate an optional DMA mapping length and use that in scsi and libata (John Garry) - split the global swiotlb lock (Tianyu Lan) - various fixes and cleanup (Chao Gao, Dan Carpenter, Dongli Zhang, Lukas Bulwahn, Robin Murphy) * tag 'dma-mapping-5.20-2022-08-06' of git://git.infradead.org/users/hch/dma-mapping: (45 commits) swiotlb: fix passing local variable to debugfs_create_ulong() dma-mapping: reformat comment to suppress htmldoc warning PCI/P2PDMA: Remove pci_p2pdma_[un]map_sg() RDMA/rw: drop pci_p2pdma_[un]map_sg() RDMA/core: introduce ib_dma_pci_p2p_dma_supported() nvme-pci: convert to using dma_map_sgtable() nvme-pci: check DMA ops when indicating support for PCI P2PDMA iommu/dma: support PCI P2PDMA pages in dma-iommu map_sg iommu: Explicitly skip bus address marked segments in __iommu_map_sg() dma-mapping: add flags to dma_map_ops to indicate PCI P2PDMA support dma-direct: support PCI P2PDMA pages in dma-direct map_sg dma-mapping: allow EREMOTEIO return code for P2PDMA transfers PCI/P2PDMA: Introduce helpers for dma_map_sg implementations PCI/P2PDMA: Attempt to set map_type if it has not been set lib/scatterlist: add flag for indicating P2PDMA segments in an SGL swiotlb: clean up some coding style and minor issues dma-mapping: update comment after dmabounce removal scsi: sd: Add a comment about limiting max_sectors to shost optimal limit ata: libata-scsi: cap ata_device->max_sectors according to shost->max_sectors scsi: scsi_transport_sas: cap shost opt_sectors according to DMA optimal limit ... 
Pull dma-mapping updates from Christoph Hellwig:

 - convert arm32 to the common dma-direct code (Arnd Bergmann, Robin
   Murphy, Christoph Hellwig)

 - restructure the PCIe peer to peer mapping support (Logan Gunthorpe)

 - allow the IOMMU code to communicate an optional DMA mapping length
   and use that in scsi and libata (John Garry)

 - split the global swiotlb lock (Tianyu Lan)

 - various fixes and cleanup (Chao Gao, Dan Carpenter, Dongli Zhang,
   Lukas Bulwahn, Robin Murphy)

* tag 'dma-mapping-5.20-2022-08-06' of git://git.infradead.org/users/hch/dma-mapping: (45 commits)
  swiotlb: fix passing local variable to debugfs_create_ulong()
  dma-mapping: reformat comment to suppress htmldoc warning
  PCI/P2PDMA: Remove pci_p2pdma_[un]map_sg()
  RDMA/rw: drop pci_p2pdma_[un]map_sg()
  RDMA/core: introduce ib_dma_pci_p2p_dma_supported()
  nvme-pci: convert to using dma_map_sgtable()
  nvme-pci: check DMA ops when indicating support for PCI P2PDMA
  iommu/dma: support PCI P2PDMA pages in dma-iommu map_sg
  iommu: Explicitly skip bus address marked segments in __iommu_map_sg()
  dma-mapping: add flags to dma_map_ops to indicate PCI P2PDMA support
  dma-direct: support PCI P2PDMA pages in dma-direct map_sg
  dma-mapping: allow EREMOTEIO return code for P2PDMA transfers
  PCI/P2PDMA: Introduce helpers for dma_map_sg implementations
  PCI/P2PDMA: Attempt to set map_type if it has not been set
  lib/scatterlist: add flag for indicating P2PDMA segments in an SGL
  swiotlb: clean up some coding style and minor issues
  dma-mapping: update comment after dmabounce removal
  scsi: sd: Add a comment about limiting max_sectors to shost optimal limit
  ata: libata-scsi: cap ata_device->max_sectors according to shost->max_sectors
  scsi: scsi_transport_sas: cap shost opt_sectors according to DMA optimal limit
  ...
Merge tag 'ata-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata 2022-08-03T22:26:04+00:00 Linus Torvalds torvalds@linux-foundation.org 2022-08-03T22:26:04+00:00 526942b8134cc34d25d27f95dfff98b8ce2f6fcd Pull ATA updates from Damien Le Moal: - Some code refactoring for the pata_hpt37x and pata_hpt3x2n drivers, from Sergei. - Several patches to cleanup in libata-core, libata-scsi and libata-eh code: fixes arguments and variables types, change some functions declaration to static and fix for a typo in a comment. From Sergey and Xiang. - Fix a compilation warning in the pata_macio driver, from me. - A fix for the expected number of resources in the sata_mv driver fix, from Andrew. * tag 'ata-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: ata: sata_mv: Fixes expected number of resources now IRQs are gone ata: libata-scsi: fix result type of ata_ioc32() ata: pata_macio: Fix compilation warning ata: libata-eh: fix sloppy result type of ata_internal_cmd_timeout() ata: libata-core: fix sloppy parameter type in ata_exec_internal[_sg]() ata: make ata_port::fastdrain_cnt *unsigned int* ata: libata-eh: fix sloppy result type of ata_eh_nr_in_flight() ata: libata-core: make ata_exec_internal_sg() *static* ata: make transfer mode masks *unsigned int* ata: libata-core: get rid of *else* branches in ata_id_n_sectors() ata: libata-core: fix sloppy typing in ata_id_n_sectors() ata: pata_hpt3x2n: pass base DPLL frequency to hpt3x2n_pci_clock() ata: pata_hpt37x: merge hpt374_read_freq() to hpt37x_pci_clock() ata: pata_hpt37x: factor out hpt37x_pci_clock() ata: pata_hpt37x: move claculating PCI clock from hpt37x_clock_slot() ata: libata: Fix syntax errors in comments 
Pull ATA updates from Damien Le Moal:

 - Some code refactoring for the pata_hpt37x and pata_hpt3x2n drivers,
   from Sergei.

 - Several patches to cleanup in libata-core, libata-scsi and libata-eh
   code: fixes arguments and variables types, change some functions
   declaration to static and fix for a typo in a comment. From Sergey
   and Xiang.

 - Fix a compilation warning in the pata_macio driver, from me.

 - A fix for the expected number of resources in the sata_mv driver fix,
   from Andrew.

* tag 'ata-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  ata: sata_mv: Fixes expected number of resources now IRQs are gone
  ata: libata-scsi: fix result type of ata_ioc32()
  ata: pata_macio: Fix compilation warning
  ata: libata-eh: fix sloppy result type of ata_internal_cmd_timeout()
  ata: libata-core: fix sloppy parameter type in ata_exec_internal[_sg]()
  ata: make ata_port::fastdrain_cnt *unsigned int*
  ata: libata-eh: fix sloppy result type of ata_eh_nr_in_flight()
  ata: libata-core: make ata_exec_internal_sg() *static*
  ata: make transfer mode masks *unsigned int*
  ata: libata-core: get rid of *else* branches in ata_id_n_sectors()
  ata: libata-core: fix sloppy typing in ata_id_n_sectors()
  ata: pata_hpt3x2n: pass base DPLL frequency to hpt3x2n_pci_clock()
  ata: pata_hpt37x: merge hpt374_read_freq() to hpt37x_pci_clock()
  ata: pata_hpt37x: factor out hpt37x_pci_clock()
  ata: pata_hpt37x: move claculating PCI clock from hpt37x_clock_slot()
  ata: libata: Fix syntax errors in comments