linux-stable.git/drivers/ata, branch v3.9.9

libata-acpi: add back ACPI based hotplug functionality

2013-07-03T17:55:36+00:00

commit 44521527be36172864e6e7a6fba4b66e9aa48e40 upstream.

Commit 30dcf76acc69 "libata: migrate ACPI code over to new bindings"
mistakenly dropped the code to register hotplug notificaion handler
for ATA port/devices, causing regression for people using ATA bay,
as kernel bug #59871 shows.

Fix this by adding back the hotplug notification handler registration
code.  Since this code has to be run once and notification needs to
be installed on every ATA port/devices handle no matter if there is
actual device attached, we can't do this in binding time for ATA
device ACPI handle, as the binding only occurs when a SCSI device is
created, i.e. there is device attached.  So introduce the
ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles
and if it is available, install the notificaion handler for it during
ATA init time.

With the ATA ACPI handle binding to SCSI device tree, it is possible
now that when the SCSI hotplug work removes the SCSI device, the ACPI
unbind function will find that the corresponding ACPI device has
already been deleted by dock driver, causing a scaring message like:
[  128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt
Fix this by waiting for SCSI hotplug task finish in our notificaion
handler, so that the removal of ACPI device done in ACPI unbind
function triggered by the removal of SCSI device is run earlier when
ACPI device is still available.

[The only change I've made is to remove the two NULL params in
register_hotplug_dock_device, which doesn't accept those params
in pre-v3.10 kernels. - aaron.lu]

[rjw: Rebased]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59871
Reported-bisected-and-tested-by: Dirk Griesbach 
Signed-off-by: Aaron Lu 
Acked-by: Tejun Heo 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

libata: make ata_exec_internal_sg honor DMADIR

2013-06-07T19:53:05+00:00

commit e771451c0a831d96a7c14b0ca8a8ec671d98567b upstream.

libata honors DMADIR for regular commands, but not for internal commands
used (among other) during device initialisation.

This makes SATA-host-to-PATA-device bridges based on Silicon Image SiL3611
(such as "Abit Serillel 2") end up disabled when used with an ATAPI device
after a few tries.

Log output of the bridge being hot-plugged with an ATAPI drive:

  [ 9631.212901] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
  [ 9631.212913] ata1: irq_stat 0x00000040, connection status changed
  [ 9631.212923] ata1: SError: { CommWake 10B8B DevExch }
  [ 9631.212939] ata1: hard resetting link
  [ 9632.104962] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  [ 9632.106393] ata1.00: ATAPI: PIONEER DVD-RW  DVR-115, 1.06, max UDMA/33
  [ 9632.106407] ata1.00: applying bridge limits
  [ 9632.108151] ata1.00: configured for UDMA/33
  [ 9637.105303] ata1.00: qc timeout (cmd 0xa0)
  [ 9637.105324] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
  [ 9637.105335] ata1: hard resetting link
  [ 9638.044599] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  [ 9638.047878] ata1.00: configured for UDMA/33
  [ 9643.044933] ata1.00: qc timeout (cmd 0xa0)
  [ 9643.044953] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
  [ 9643.044963] ata1: limiting SATA link speed to 1.5 Gbps
  [ 9643.044971] ata1.00: limiting speed to UDMA/33:PIO3
  [ 9643.044979] ata1: hard resetting link
  [ 9643.984225] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
  [ 9643.987471] ata1.00: configured for UDMA/33
  [ 9648.984591] ata1.00: qc timeout (cmd 0xa0)
  [ 9648.984612] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
  [ 9648.984619] ata1.00: disabled
  [ 9649.000593] ata1: hard resetting link
  [ 9649.939902] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
  [ 9649.955864] ata1: EH complete

With this patch, the drive enumerates correctly when libata is loaded with
atapi_dmadir=1:

  [ 9891.810863] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
  [ 9891.810874] ata1: irq_stat 0x00000040, connection status changed
  [ 9891.810884] ata1: SError: { CommWake 10B8B DevExch }
  [ 9891.810900] ata1: hard resetting link
  [ 9892.762105] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  [ 9892.763544] ata1.00: ATAPI: PIONEER DVD-RW  DVR-115, 1.06, max UDMA/33, DMADIR
  [ 9892.763558] ata1.00: applying bridge limits
  [ 9892.765393] ata1.00: configured for UDMA/33
  [ 9892.786063] ata1: EH complete
  [ 9892.792062] scsi 0:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-115  1.06 PQ: 0 ANSI: 5
  [ 9892.798455] sr2: scsi3-mmc drive: 12x/12x writer dvd-ram cd/rw xa/form2 cdda tray
  [ 9892.798837] sr 0:0:0:0: Attached scsi CD-ROM sr2
  [ 9892.799109] sr 0:0:0:0: Attached scsi generic sg6 type 5

Based on a patch by Csaba Halász  on linux-ide:
http://marc.info/?l=linux-ide&m=136121147832295&w=2

tj: minor formatting changes.

Signed-off-by: Vincent Pelletier 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

ata_piix: add PCI IDs for Intel BayTail

2013-06-07T19:53:04+00:00

commit fca8c90d519dedd4f4b19901d005c243f7f0bf2e upstream.

Adds IDE-mode SATA Device IDs for the Intel BayTrail platform.

Signed-off-by: Chew, Chiau Ee 
Signed-off-by: Artem Bityutskiy 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

sata_rcar: fix interrupt handling

2013-06-07T19:53:04+00:00

commit 52a2a1087b5924de00484f35ef5e2a73f61dbd22 upstream.

The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.

Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear  only those interrupts  that we have read
as active first time around, because else we have  a  race and risk clearing  an
interrupt that  can  occur between read  and write of the  SATAINTSTAT  register
and never registering it...

Signed-off-by: Sergei Shtylyov 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

sata_rcar: clear STOP bit in bmdma_start() method

2013-06-07T19:53:04+00:00

commit df7e131f6359f20ed8f0a37db039c4f6420a18c2 upstream.

Iff bmdma_setup() has to stop a DMA transfer before starting a new
one, then the STOP bit in the ATAPI_CONTROL1 register will remain set
(it's only cleared when setting the START bit to 1) and then
bmdma_start() method will set both START and STOP bits simultaneously
which should abort the transfer being just started.  Avoid that by
explicitly clearing the STOP bit in bmdma_start() method (in this case
it will be ignored on write).

Signed-off-by: Sergei Shtylyov 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

sata_highbank: Rename proc_name to the module name

2013-05-08T03:33:12+00:00

commit 2cc1144a31f76d4a9fb48bec5d6ba1359f980813 upstream.

mkinitrd looks at /sys/class/scsi_host/host$hostnum/proc_name to find
the module name of a disk driver. Current name is "highbank-ahci" but
the module is "sata_highbank". Rename it to match the module name.

Signed-off-by: Robert Richter 
Cc: Rob Herring 
Cc: Alexander Graf 
Signed-off-by: Jeff Garzik 
Signed-off-by: Greg Kroah-Hartman

libata: acpi: make ata_ap_acpi_handle not block

2013-05-08T03:33:11+00:00

commit d66af4df0837f21bf267305dc5ccab2d29e24d86 upstream.

Since commit 30dcf76acc, ata_ap_acpi_handle will always do a namespace
walk, which requires acquiring an acpi namespace mutex. This made it
impossible to be used when calling path has held a spinlock.

For example, it can occur in the following code path for pata_acpi:
ata_scsi_queuecmd (ap->lock is acquired)
  __ata_scsi_queuecmd
    ata_scsi_translate
      ata_qc_issue
        pacpi_qc_issue
          ata_acpi_stm
            ata_ap_acpi_handle
              acpi_get_child
                acpi_walk_namespace
                  acpi_ut_acquire_mutex (acquire mutex while holding lock)
This caused scheduling while atomic bug, as reported in bug #56781.

Actually, ata_ap_acpi_handle doesn't have to walk the namespace every
time it is called, it can simply return the bound acpi handle on the
corresponding SCSI host. The reason previously it is not done this way
is, ata_ap_acpi_handle is used in the binding function
ata_acpi_bind_host by ata_acpi_gtm when the handle is not bound to the
SCSI host yet. Since we already have the ATA port's handle in its
binding function, we can simply use it instead of calling
ata_ap_acpi_handle there. So introduce a new function __ata_acpi_gtm,
where it will receive an acpi handle param in addition to the ATA port
which is solely used for debug statement. With this change, we can make
ata_ap_acpi_handle simply return the bound handle for SCSI host instead
of walking the acpi namespace now.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=56781
Reported-and-tested-by: 
Signed-off-by: Aaron Lu 
Signed-off-by: Jeff Garzik 
Signed-off-by: Greg Kroah-Hartman

[libata] Fix HDIO_DRIVE_* ioctl() Linux 3.9 regression

2013-04-03T23:48:49+00:00

On Mon, Mar 25, 2013 at 06:26:50PM +0100, Ronald wrote:
> In reply to [1]: I have the same issue. Git bisect took 50+ rebuilds xD
>
> Smartd does not work anymore since 84a9a8cd9 ([libata] Set proper SK
> when CK_COND is set.).

> [1] http://www.spinics.net/lists/linux-ide/msg45268.html

It seems that the SAM_STAT_CHECK_CONDITION is not cleared
causing -EIO, because that patch modified sensebuf and
the check for clearing SAM_STAT_CHECK_CONDITION is no longer valid.

Fix that.

Signed-off-by: Jeff Garzik

libata: fix DMA to stack in reading devslp_timing parameters

2013-04-03T23:45:57+00:00

Commit 803739d25c2343da6d2f95eebdcbc08bf67097d4 ("[libata] replace
sata_settings with devslp_timing"), which was also Cc: stable, used a
stack buffer to receive data from ata_read_log_page(), which triggers
the following warning:
 ahci 0000:00:1f.2: DMA-API: device driver maps memory fromstack [addr=ffff880140469948]

Fix this by using ap->sector_buf instead of a stack buffer.

Signed-off-by: David Woodhouse 
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik

ata_piix: Fix DVD not dectected at some Haswell platforms

2013-04-03T23:43:36+00:00

There is a quirk patch 5e5a4f5d5a08c9c504fe956391ac3dae2c66556d
"ata_piix: make DVD Drive recognisable on systems with Intel Sandybridge
 chipsets(v2)" fixing the 4 ports IDE controller 32bit PIO mode.

We've hit a problem with DVD not recognized on Haswell Desktop platform which
includes Lynx Point 2-port SATA controller.

This quirk patch disables 32bit PIO on this controller in IDE mode.

v2: Change spelling error in statememnt pointed by Sergei Shtylyov.
v3: Change comment statememnt and spliting line over 80 characters pointed by
    Libor Pechacek and also rebase the patch against 3.8-rc7 kernel.

Tested-by: Lee, Chun-Yi 
Signed-off-by: Youquan Song 
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Garzik