linux-stable.git/drivers/ata, branch v3.7.3

libata: fix Null pointer dereference on disk error

2013-01-17T16:45:58+00:00

commit 26cd4d65deba587f3cf2329b6869ce02bcbe68ec upstream.

Following oops were observed when disk error happened:

[ 4272.896937] sd 0:0:0:0: [sda] Unhandled error code
[ 4272.896939] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 4272.896942] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 00 5a de a7 00 00 08 00
[ 4272.896951] end_request: I/O error, dev sda, sector 5955239
[ 4291.574947] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 4291.658305] IP: [] ahci_activity_show+0x1/0x40
[ 4291.730090] PGD 76dbbc067 PUD 6c4fba067 PMD 0
[ 4291.783408] Oops: 0000 [#1] SMP
[ 4291.822100] last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/sw_activity
[ 4291.934235] CPU 9
[ 4291.958301] Pid: 27942, comm: hwinfo ......

ata_scsi_find_dev could return NULL, so ata_scsi_activity_{show,store} should check if atadev is NULL.

Signed-off-by: Xiaotian Feng 
Cc: James Bottomley 
Signed-off-by: Jeff Garzik 
Signed-off-by: Greg Kroah-Hartman

libata: set dma_mode to 0xff in reset

2013-01-17T16:45:58+00:00

commit 5416912af75de9cba5d1c75b99a7888b0bbbd2fb upstream.

ata_device->dma_mode's initial value is zero, which is not a valid dma
mode, but ata_dma_enabled will return true for this value. This patch
sets dma_mode to 0xff in reset function, so that ata_dma_enabled will
not return true for this case, or it will cause problem for pata_acpi.

The corrsponding bugzilla page is at:
https://bugzilla.kernel.org/show_bug.cgi?id=49151

Reported-by: Phillip Wood 
Signed-off-by: Aaron Lu 
Tested-by: Szymon Janc 
Tested-by: Dutra Julio 
Acked-by: Alan Cox 
Signed-off-by: Jeff Garzik 
Signed-off-by: Greg Kroah-Hartman

sata_promise: fix hardreset lockdep error

2013-01-17T16:45:57+00:00

commit 3100d49d3cd236443faae9d81137c81b22d36003 upstream.

sata_promise's pdc_hard_reset_port() needs to serialize because it
flips a port-specific bit in controller register that's shared by
all ports. The code takes the ata host lock for this, but that's
broken because an interrupt may arrive on our irq during the hard
reset sequence, and that too will take the ata host lock. With
lockdep enabled a big nasty warning is seen.

Fixed by adding private state to the ata host structure, containing
a second lock used only for serializing the hard reset sequences.
This eliminated the lockdep warnings both on my test rig and on
the original reporter's machine.

Signed-off-by: Mikael Pettersson 
Tested-by: Adko Branil 
Signed-off-by: Jeff Garzik 
Signed-off-by: Greg Kroah-Hartman

libata: restore acpi disable functionality

2013-01-11T17:18:35+00:00

commit 0d0cdb028f9d9771e2b346038707734121f906e3 upstream.

Commit 66fa7f215 "libata-acpi: improve ACPI disabling" introdcued the
behaviour of disabling ATA ACPI if ata_acpi_on_devcfg failed the 2nd
time, but commit 30dcf76ac dropped this behaviour and this caused
problem for Dimitris Damigos, where his laptop can not resume correctly.

The bugzilla page for it is:
https://bugzilla.kernel.org/show_bug.cgi?id=49331

The problem is, ata_dev_push_id will fail the 2nd time it is invoked,
and due to disabling ACPI code is dropped, ata_acpi_on_devcfg which
calls ata_dev_push_id will keep failing and eventually made the device
disabled.

This patch restores the original behaviour, if acpi failed the 2nd time,
disable acpi functionality for the device(and we do not event need to
add a debug message for this as it is still there ;-).

Reported-by: Dimitris Damigos 
Signed-off-by: Aaron Lu 
Signed-off-by: Jeff Garzik 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

2012-11-22T19:14:54+00:00

Pull SCSI fixes from James Bottomley:
 "This is a set of four bug fixes.

  The isci one is an obvious thinko (using request buffer instead of
  response buffer) which causes a command to fail.

  The three others are DIF/DIX updates which are required because
  they're part of a series of ten patches, the other seven of which went
  into the block layer during the merge window meaning our current
  DIF/DIX implementation is broken without these three.

  Signed-off-by: James Bottomley "

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] sd: Implement support for WRITE SAME
  [SCSI] sd: Permit merged discard requests
  [SCSI] Add a report opcode helper
  [SCSI] isci: copy fis 0x34 response into proper buffer

[libata] PM callbacks should be conditionally compiled on CONFIG_PM_SLEEP

2012-11-16T05:45:37+00:00

This will fix warnings like following when CONFIG_PM_SLEEP is not set:

        warning: 'xxx_suspend' defined but not used [-Wunused-function]
        warning: 'xxx_resume' defined but not used [-Wunused-function]

Because
	SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)

Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).

Cc: Viresh Kumar 
Cc: linux-ide@vger.kernel.org
Signed-off-by: Yuanhan Liu 
Signed-off-by: Fengguang Wu 
Signed-off-by: Jeff Garzik

sata_svw: check DMA start bit before reset

2012-11-16T04:54:41+00:00

If kdump is triggered with pending IO, controller may not respond causing
kdump to fail.

http://marc.info/?l=linux-ide&m=133032255424658&w=2

During error recovery ata_do_dev_read_id never completes due hang
in mmio_insw.

ata_do_dev_read_id
 ata_sff_data_xfer
  ioread16_rep
   mmio_insw

if DMA start bit is cleared before reset, PIO command is successful
and kdump succeeds.

Signed-off-by: David Milburn 
Signed-off-by: Jeff Garzik

libata debugging: Warn when unable to find timing descriptor based on xfer_mode

2012-11-16T04:51:11+00:00

ata_timing_find_mode could return NULL which is not checked by all
low-level ATA drivers using it and cause a NULL ptr deref. Warn at least
so that possible issues can get fixed easily.

Signed-off-by: Borislav Petkov 
Signed-off-by: Jeff Garzik

sata_highbank: mark ahci_highbank_probe as __devinit

2012-11-16T04:44:27+00:00

The ahci_highbank_probe function is incorrectly marked as __init,
which means it can get discarded at boot time, which might be
a problem if for some reason the device only becomes operational
after loading another module.

Using __devinit instead avoids seeing this warning for every build:

WARNING: vmlinux.o(.data+0xf7b0): Section mismatch in reference from the
variable ahci_highbank_driver to the function .init.text:ahci_highbank_probe()
The variable ahci_highbank_driver references
the function __init ahci_highbank_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console

Signed-off-by: Arnd Bergmann 
Cc: Mark Langsdorf 
Cc: Rob Herring 
Signed-off-by: Jeff Garzik

pata_arasan: Initialize cf clock to 166MHz

2012-11-16T04:40:20+00:00

PATA arasan driver expects the clock to be set to 166 MHz for proper
functioning.  This patch sets clk to 166 MHz in probe.

Signed-off-by: Vipul Kumar Samar 
Signed-off-by: Viresh Kumar 
Signed-off-by: Jeff Garzik