linux-stable.git/drivers/ata, branch v3.7.1

Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

2012-11-22T19:14:54+00:00

Pull SCSI fixes from James Bottomley:
 "This is a set of four bug fixes.

  The isci one is an obvious thinko (using request buffer instead of
  response buffer) which causes a command to fail.

  The three others are DIF/DIX updates which are required because
  they're part of a series of ten patches, the other seven of which went
  into the block layer during the merge window meaning our current
  DIF/DIX implementation is broken without these three.

  Signed-off-by: James Bottomley "

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] sd: Implement support for WRITE SAME
  [SCSI] sd: Permit merged discard requests
  [SCSI] Add a report opcode helper
  [SCSI] isci: copy fis 0x34 response into proper buffer

[libata] PM callbacks should be conditionally compiled on CONFIG_PM_SLEEP

2012-11-16T05:45:37+00:00

This will fix warnings like following when CONFIG_PM_SLEEP is not set:

        warning: 'xxx_suspend' defined but not used [-Wunused-function]
        warning: 'xxx_resume' defined but not used [-Wunused-function]

Because
	SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)

Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).

Cc: Viresh Kumar 
Cc: linux-ide@vger.kernel.org
Signed-off-by: Yuanhan Liu 
Signed-off-by: Fengguang Wu 
Signed-off-by: Jeff Garzik

sata_svw: check DMA start bit before reset

2012-11-16T04:54:41+00:00

If kdump is triggered with pending IO, controller may not respond causing
kdump to fail.

http://marc.info/?l=linux-ide&m=133032255424658&w=2

During error recovery ata_do_dev_read_id never completes due hang
in mmio_insw.

ata_do_dev_read_id
 ata_sff_data_xfer
  ioread16_rep
   mmio_insw

if DMA start bit is cleared before reset, PIO command is successful
and kdump succeeds.

Signed-off-by: David Milburn 
Signed-off-by: Jeff Garzik

libata debugging: Warn when unable to find timing descriptor based on xfer_mode

2012-11-16T04:51:11+00:00

ata_timing_find_mode could return NULL which is not checked by all
low-level ATA drivers using it and cause a NULL ptr deref. Warn at least
so that possible issues can get fixed easily.

Signed-off-by: Borislav Petkov 
Signed-off-by: Jeff Garzik

sata_highbank: mark ahci_highbank_probe as __devinit

2012-11-16T04:44:27+00:00

The ahci_highbank_probe function is incorrectly marked as __init,
which means it can get discarded at boot time, which might be
a problem if for some reason the device only becomes operational
after loading another module.

Using __devinit instead avoids seeing this warning for every build:

WARNING: vmlinux.o(.data+0xf7b0): Section mismatch in reference from the
variable ahci_highbank_driver to the function .init.text:ahci_highbank_probe()
The variable ahci_highbank_driver references
the function __init ahci_highbank_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console

Signed-off-by: Arnd Bergmann 
Cc: Mark Langsdorf 
Cc: Rob Herring 
Signed-off-by: Jeff Garzik

pata_arasan: Initialize cf clock to 166MHz

2012-11-16T04:40:20+00:00

PATA arasan driver expects the clock to be set to 166 MHz for proper
functioning.  This patch sets clk to 166 MHz in probe.

Signed-off-by: Vipul Kumar Samar 
Signed-off-by: Viresh Kumar 
Signed-off-by: Jeff Garzik

libata-acpi: Fix NULL ptr derference in ata_acpi_dev_handle

2012-11-16T04:20:55+00:00

commit 6b66d95895c149cbc04d4fac5a2f5477c543a8ae didn't handle SATA PMP
case in ata_acpi_bind_device and will cause a NULL ptr dereference when
user attached a SATA drive to the PMP port. Fix this by checking PMP
support.

This bug is reported by Dan van der Ster in the following bugzilla page:
https://bugzilla.kernel.org/show_bug.cgi?id=48211

Reported-by: Dan van der Ster 
Tested-by: Dan van der Ster 
Signed-off-by: Aaron Lu 
Cc: 
Signed-off-by: Jeff Garzik 
Tested-by: Simon

[SCSI] sd: Implement support for WRITE SAME

2012-11-14T06:45:42+00:00

Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.

 - We set the default maximum to 0xFFFF because there are several
   devices out there that only support two-byte block counts even with
   WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
   device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
   LIMITS VPD.

 - max_write_same_blocks can be overriden per-device basis in sysfs.

 - The UNMAP discovery heuristics remain unchanged but the discard
   limits are tweaked to match the "real" WRITE SAME commands.

 - In the error handling logic we now distinguish between WRITE SAME
   with and without UNMAP set.

The discovery process heuristics are:

 - If the device reports a SCSI level of SPC-3 or greater we'll issue
   READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
   supported. If that's the case we will use it.

 - If the device supports the block limits VPD and reports a MAXIMUM
   WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).

 - Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
   0xFFFFFFFF or the block count exceeds 0xFFFF.

 - no_write_same is set for ATA, FireWire and USB.

Signed-off-by: Martin K. Petersen 
Reviewed-by: Mike Snitzer 
Reviewed-by: Jeff Garzik 
Signed-off-by: James Bottomley

[SCSI] Add a report opcode helper

2012-11-14T05:11:31+00:00

The REPORT SUPPORTED OPERATION CODES command can be used to query
whether a given opcode is supported by a device. Add a helper function
that allows us to look up commands.

We only issue RSOC if the device reports compliance with SPC-3 or
later. But to err on the side of caution we disable the command for ATA,
FireWire and USB.

Signed-off-by: Martin K. Petersen 
Acked-by: Mike Snitzer 
Signed-off-by: James Bottomley

Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

2012-10-03T02:01:32+00:00

Pull first round of SCSI updates from James Bottomley:
 "This is a large set of updates, mostly for drivers (qla2xxx [including
  support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
  be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).

  There's also a rework for tape adding virtually unlimited numbers of
  tape drives plus a set of dif fixes for sd and a fix for a live lock
  on hot remove of SCSI devices.

  This round includes a signed tag pull of isci-for-3.6

  Signed-off-by: James Bottomley "

Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
  [SCSI] st: remove st_mutex
  [SCSI] sd: Ensure we correctly disable devices with unknown protection type
  [SCSI] hpsa: gen8plus Smart Array IDs
  [SCSI] qla4xxx: Update driver version to 5.03.00-k1
  [SCSI] qla4xxx: Disable generating pause frames for ISP83XX
  [SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
  [SCSI] qla4xxx: IDC implementation for Loopback
  [SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
  [SCSI] qla4xxx: Fix panic while rmmod
  [SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
  [SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
  [SCSI] qla4xxx: Update idc reg in case of PCI AER
  [SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
  [SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
  [SCSI] qla4xxx: Print correct IDC version
  [SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
  [SCSI] scsi_dh_alua: Enable STPG for unavailable ports
  [SCSI] scsi_remove_target: fix softlockup regression on hot remove
  [SCSI] ibmvscsi: Fix host config length field overflow
  [SCSI] ibmvscsi: Remove backend abstraction
  ...