linux-stable.git/drivers/ata, branch linux-6.5.y

ata: pata_parport: fit3: implement IDE command set registers

2023-11-08T13:08:57+00:00

[ Upstream commit 0c1e81d0b5ebd5813536dd5fcf5966ad043f37dc ]

fit3 protocol driver does not support accessing IDE control registers
(device control/altstatus). The DOS driver does not use these registers
either (as observed from DOSEMU trace). But the HW seems to be capable
of accessing these registers - I simply tried bit 3 and it works!

The control register is required to properly reset ATAPI devices or
they will be detected only once (after a power cycle).

Tested with EXP Computer CD-865 with MC-1285B EPP cable and
TransDisk 3000.

Signed-off-by: Ondrej Zary 
Reviewed-by: Sergey Shtylyov 
Signed-off-by: Damien Le Moal 
Signed-off-by: Sasha Levin

ata: pata_parport: add custom version of wait_after_reset

2023-11-08T13:08:57+00:00

[ Upstream commit f343e578fef99a69b3322aca38b94a6d8ded2ce7 ]

Some parallel adapters (e.g. EXP Computer MC-1285B EPP Cable) return
bogus values when there's no master device present. This can cause
reset to fail, preventing the lone slave device (such as EXP Computer
CD-865) from working.

Add custom version of wait_after_reset that ignores master failure when
a slave device is present. The custom version is also needed because
the generic ata_sff_wait_after_reset uses direct port I/O for slave
device detection.

Signed-off-by: Ondrej Zary 
Reviewed-by: Sergey Shtylyov 
Signed-off-by: Damien Le Moal 
Signed-off-by: Sasha Levin

scsi: sd: Introduce manage_shutdown device flag

2023-11-02T08:36:55+00:00

commit 24eca2dce0f8d19db808c972b0281298d0bafe99 upstream.

Commit aa3998dbeb3a ("ata: libata-scsi: Disable scsi device
manage_system_start_stop") change setting the manage_system_start_stop
flag to false for libata managed disks to enable libata internal
management of disk suspend/resume. However, a side effect of this change
is that on system shutdown, disks are no longer being stopped (set to
standby mode with the heads unloaded). While this is not a critical
issue, this unclean shutdown is not recommended and shows up with
increased smart counters (e.g. the unexpected power loss counter
"Unexpect_Power_Loss_Ct").

Instead of defining a shutdown driver method for all ATA adapter
drivers (not all of them define that operation), this patch resolves
this issue by further refining the sd driver start/stop control of disks
using the new flag manage_shutdown. If this new flag is set to true by
a low level driver, the function sd_shutdown() will issue a
START STOP UNIT command with the start argument set to 0 when a disk
needs to be powered off (suspended) on system power off, that is, when
system_state is equal to SYSTEM_POWER_OFF.

Similarly to the other manage_xxx flags, the new manage_shutdown flag is
exposed through sysfs as a read-write device attribute.

To avoid any confusion between manage_shutdown and
manage_system_start_stop, the comments describing these flags in
include/scsi/scsi.h are also improved.

Fixes: aa3998dbeb3a ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218038
Link: https://lore.kernel.org/all/cd397c88-bf53-4768-9ab8-9d107df9e613@gmail.com/
Signed-off-by: Damien Le Moal 
Reviewed-by: Niklas Cassel 
Reviewed-by: Hannes Reinecke 
Reviewed-by: James Bottomley 
Acked-by: Martin K. Petersen 
Signed-off-by: Greg Kroah-Hartman

ata: libata-eh: Fix compilation warning in ata_eh_link_report()

2023-10-25T10:16:17+00:00

[ Upstream commit 49728bdc702391902a473b9393f1620eea32acb0 ]

The 6 bytes length of the tries_buf string in ata_eh_link_report() is
too short and results in a gcc compilation warning with W-!:

drivers/ata/libata-eh.c: In function ‘ata_eh_link_report’:
drivers/ata/libata-eh.c:2371:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 4 [-Wformat-truncation=]
 2371 |                 snprintf(tries_buf, sizeof(tries_buf), " t%d",
      |                                                           ^~
drivers/ata/libata-eh.c:2371:56: note: directive argument in the range [-2147483648, 4]
 2371 |                 snprintf(tries_buf, sizeof(tries_buf), " t%d",
      |                                                        ^~~~~~
drivers/ata/libata-eh.c:2371:17: note: ‘snprintf’ output between 4 and 14 bytes into a destination of size 6
 2371 |                 snprintf(tries_buf, sizeof(tries_buf), " t%d",
      |                 ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 2372 |                          ap->eh_tries);
      |                          ~~~~~~~~~~~~~

Avoid this warning by increasing the string size to 16B.

Signed-off-by: Damien Le Moal 
Reviewed-by: Hannes Reinecke 
Tested-by: Geert Uytterhoeven 
Reviewed-by: Martin K. Petersen 
Signed-off-by: Sasha Levin

ata: libata-core: Fix compilation warning in ata_dev_config_ncq()

2023-10-25T10:16:17+00:00

[ Upstream commit ed518d9ba980dc0d27c7d1dea1e627ba001d1977 ]

The 24 bytes length allocated to the ncq_desc string in
ata_dev_config_lba() for ata_dev_config_ncq() to use is too short,
causing the following gcc compilation warnings when compiling with W=1:

drivers/ata/libata-core.c: In function ‘ata_dev_configure’:
drivers/ata/libata-core.c:2378:56: warning: ‘%d’ directive output may be truncated writing between 1 and 2 bytes into a region of size between 1 and 11 [-Wformat-truncation=]
 2378 |                 snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
      |                                                        ^~
In function ‘ata_dev_config_ncq’,
    inlined from ‘ata_dev_config_lba’ at drivers/ata/libata-core.c:2649:8,
    inlined from ‘ata_dev_configure’ at drivers/ata/libata-core.c:2952:9:
drivers/ata/libata-core.c:2378:41: note: directive argument in the range [1, 32]
 2378 |                 snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
      |                                         ^~~~~~~~~~~~~~~~~~~~~
drivers/ata/libata-core.c:2378:17: note: ‘snprintf’ output between 16 and 31 bytes into a destination of size 24
 2378 |                 snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
      |                 ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 2379 |                         ddepth, aa_desc);
      |                         ~~~~~~~~~~~~~~~~

Avoid these warnings and the potential truncation by changing the size
of the ncq_desc string to 32 characters.

Signed-off-by: Damien Le Moal 
Reviewed-by: Hannes Reinecke 
Tested-by: Geert Uytterhoeven 
Reviewed-by: Martin K. Petersen 
Signed-off-by: Sasha Levin

ata: libata-scsi: Disable scsi device manage_system_start_stop

2023-10-19T21:10:56+00:00

commit aa3998dbeb3abce63653b7f6d4542e7dcd022590 upstream.

The introduction of a device link to create a consumer/supplier
relationship between the scsi device of an ATA device and the ATA port
of that ATA device fixes the ordering of system suspend and resume
operations. For suspend, the scsi device is suspended first and the ata
port after it. This is fine as this allows the synchronize cache and
START STOP UNIT commands issued by the scsi disk driver to be executed
before the ata port is disabled.

For resume operations, the ata port is resumed first, followed
by the scsi device. This allows having the request queue of the scsi
device to be unfrozen after the ata port resume is scheduled in EH,
thus avoiding to see new requests prematurely issued to the ATA device.
Since libata sets manage_system_start_stop to 1, the scsi disk resume
operation also results in issuing a START STOP UNIT command to the
device being resumed so that the device exits standby power mode.

However, restoring the ATA device to the active power mode must be
synchronized with libata EH processing of the port resume operation to
avoid either 1) seeing the start stop unit command being received too
early when the port is not yet resumed and ready to accept commands, or
after the port resume process issues commands such as IDENTIFY to
revalidate the device. In this last case, the risk is that the device
revalidation fails with timeout errors as the drive is still spun down.

Commit 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
disabled issuing the START STOP UNIT command to avoid issues with it.
But this is incorrect as transitioning a device to the active power
mode from the standby power mode set on suspend requires a media access
command. The IDENTIFY, READ LOG and SET FEATURES commands executed in
libata EH context triggered by the ata port resume operation may thus
fail.

Fix these synchronization issues is by handling a device power mode
transitions for system suspend and resume directly in libata EH context,
without relying on the scsi disk driver management triggered with the
manage_system_start_stop flag.

To do this, the following libata helper functions are introduced:

1) ata_dev_power_set_standby():

This function issues a STANDBY IMMEDIATE command to transitiom a device
to the standby power mode. For HDDs, this spins down the disks. This
function applies only to ATA and ZAC devices and does nothing otherwise.
This function also does nothing for devices that have the
ATA_FLAG_NO_POWEROFF_SPINDOWN or ATA_FLAG_NO_HIBERNATE_SPINDOWN flag
set.

For suspend, call ata_dev_power_set_standby() in
ata_eh_handle_port_suspend() before the port is disabled and frozen.
ata_eh_unload() is also modified to transition all enabled devices to
the standby power mode when the system is shutdown or devices removed.

2) ata_dev_power_set_active() and

This function applies to ATA or ZAC devices and issues a VERIFY command
for 1 sector at LBA 0 to transition the device to the active power mode.
For HDDs, since this function will complete only once the disk spin up.
Its execution uses the same timeouts as for reset, to give the drive
enough time to complete spinup without triggering a command timeout.

For resume, call ata_dev_power_set_active() in
ata_eh_revalidate_and_attach() after the port has been enabled and
before any other command is issued to the device.

With these changes, the manage_system_start_stop and no_start_on_resume
scsi device flags do not need to be set in ata_scsi_dev_config(). The
flag manage_runtime_start_stop is still set to allow the sd driver to
spinup/spindown a disk through the sd runtime operations.

Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal 
Reviewed-by: Hannes Reinecke 
Tested-by: Geert Uytterhoeven 
Reviewed-by: Martin K. Petersen 
Signed-off-by: Greg Kroah-Hartman

ata: pata_parport: implement set_devctl

2023-10-19T21:10:56+00:00

commit d2302427c12277929c9f390adeda19fbf403c0bb upstream.

Add missing ops->sff_set_devctl implementation.

Fixes: 246a1c4c6b7f ("ata: pata_parport: add driver (PARIDE replacement)")
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Zary 
Reviewed-by: Sergey Shtylyov 
Signed-off-by: Damien Le Moal 
Signed-off-by: Greg Kroah-Hartman

ata: pata_parport: fix pata_parport_devchk

2023-10-19T21:10:56+00:00

commit b555aa66760f17df4a0a5e4b440816e390311a38 upstream.

There's a 'x' missing in 0x55 in pata_parport_devchk(), causing the
detection to always fail. Fix it.

Fixes: 246a1c4c6b7f ("ata: pata_parport: add driver (PARIDE replacement)")
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Zary 
Reviewed-by: Sergey Shtylyov 
Signed-off-by: Damien Le Moal 
Signed-off-by: Greg Kroah-Hartman

ata: libata-scsi: Fix delayed scsi_rescan_device() execution

2023-10-10T20:02:54+00:00

[ Upstream commit 8b4d9469d0b0e553208ee6f62f2807111fde18b9 ]

Commit 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after
device resume") modified ata_scsi_dev_rescan() to check the scsi device
"is_suspended" power field to ensure that the scsi device associated
with an ATA device is fully resumed when scsi_rescan_device() is
executed. However, this fix is problematic as:
1) It relies on a PM internal field that should not be used without PM
   device locking protection.
2) The check for is_suspended and the call to scsi_rescan_device() are
   not atomic and a suspend PM event may be triggered between them,
   casuing scsi_rescan_device() to be called on a suspended device and
   in that function blocking while holding the scsi device lock. This
   would deadlock a following resume operation.
These problems can trigger PM deadlocks on resume, especially with
resume operations triggered quickly after or during suspend operations.
E.g., a simple bash script like:

for (( i=0; i<10; i++ )); do
	echo "+2 > /sys/class/rtc/rtc0/wakealarm
	echo mem > /sys/power/state
done

that triggers a resume 2 seconds after starting suspending a system can
quickly lead to a PM deadlock preventing the system from correctly
resuming.

Fix this by replacing the check on is_suspended with a check on the
return value given by scsi_rescan_device() as that function will fail if
called against a suspended device. Also make sure rescan tasks already
scheduled are first cancelled before suspending an ata port.

Fixes: 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal 
Reviewed-by: Hannes Reinecke 
Reviewed-by: Niklas Cassel 
Tested-by: Geert Uytterhoeven 
Reviewed-by: Martin K. Petersen 
Signed-off-by: Sasha Levin

scsi: core: Improve type safety of scsi_rescan_device()

2023-10-10T20:02:54+00:00

[ Upstream commit 79519528a180c64a90863db2ce70887de6c49d16 ]

Most callers of scsi_rescan_device() have the scsi_device pointer readily
available. Pass a struct scsi_device pointer to scsi_rescan_device()
instead of a struct device pointer. This change prevents that a pointer to
another struct device would be passed accidentally to scsi_rescan_device().

Remove the scsi_rescan_device() declaration from the scsi_priv.h header
file since it duplicates the declaration in .

Reviewed-by: Hannes Reinecke 
Reviewed-by: Damien Le Moal 
Reviewed-by: John Garry 
Cc: Mike Christie 
Cc: Ming Lei 
Signed-off-by: Bart Van Assche 
Link: https://lore.kernel.org/r/20230822153043.4046244-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen 
Stable-dep-of: 8b4d9469d0b0 ("ata: libata-scsi: Fix delayed scsi_rescan_device() execution")
Signed-off-by: Sasha Levin