linux-stable.git/drivers/ata/ahci_platform.c, branch linux-6.2.y

ata: ahci: Add DWC AHCI SATA controller support

2022-09-16T16:40:15+00:00

Synopsys AHCI SATA controller can work pretty under with the generic
AHCI-platform driver control. But there are vendor-specific peculiarities
which can tune the device performance up and which may need to be fixed up
for proper device functioning. In addition some DWC AHCI-based controllers
may require small platform-specific fixups, so adding them in the generic
AHCI driver would have ruined the code simplicity. Shortly speaking in
order to keep the generic AHCI-platform code clean and have DWC AHCI
SATA-specific features supported we suggest to add a dedicated DWC AHCI
SATA device driver. Aside with the standard AHCI-platform resources
getting, enabling/disabling and the controller registration the new driver
performs the next actions.

First of all there is a way to verify whether the HBA/ports capabilities
activated in OF are correct. Almost all features availability is reflected
in the vendor-specific parameters registers. So the DWC AHCI driver does
the capabilities sanity check based on the corresponding fields state.

Secondly if either the Command Completion Coalescing or the Device Sleep
feature is enabled the DWC AHCI-specific internal 1ms timer must be fixed
in accordance with the application clock signal frequency. In particular
the timer value must be set to be Fapp * 1000. Normally the SoC designers
pre-configure the TIMER1MS register to contain a correct value by default.
But the platforms can support the application clock rate change. If that
happens the 1ms timer value must be accordingly updated otherwise the
dependent features won't work as expected. In the DWC AHCI driver we
suggest to rely on the "aclk" reference clock rate to set the timer
interval up. That clock source is supposed to be the AHCI SATA application
clock in accordance with the DT bindings.

Finally DWC AHCI SATA controller AXI/AHB bus DMA-engine can be tuned up to
transfer up to 1024 * FIFO words at a time by setting the Tx/Rx
transaction size in the DMA control register. The maximum value depends on
the DMA data bus and AXI/AHB bus maximum burst length. In most of the
cases it's better to set the maximum possible value to reach the best AHCI
SATA controller performance. But sometimes in order to improve the system
interconnect responsiveness, transferring in smaller data chunks may be
more preferable. For such cases and for the case when the default value
doesn't provide the best DMA bus performance we suggest to use the new
HBA-port specific DT-properties "snps,{tx,rx}-ts-max" to tune the DMA
transactions size up.

After all the settings denoted above are handled the DWC AHCI SATA driver
proceeds further with the standard AHCI-platform host initializations.

Note since DWC AHCI controller is now have a dedicated driver we can
discard the corresponding compatible string from the ahci-platform.c
module. The same concerns "snps,spear-ahci" compatible string, which is
also based on the DWC AHCI IP-core.

Signed-off-by: Serge Semin 
Reviewed-by: Hannes Reinecke 
Signed-off-by: Damien Le Moal

ata: libahci_platform: Parse ports-implemented property in resources getter

2022-09-16T16:39:30+00:00

The ports-implemented property is mainly used on the OF-based platforms
with no ports mapping initialized by a bootloader/BIOS firmware. Seeing
the same of_property_read_u32()-based pattern has already been implemented
in the generic AHCI LLDD (glue) driver and in the Mediatek, St AHCI
drivers let's move the property read procedure to the generic
ahci_platform_get_resources() method. Thus we'll have the forced ports
mapping feature supported for each OF-based platform which requires that,
and stop re-implementing the same pattern in there a bit simplifying the
code.

Signed-off-by: Serge Semin 
Signed-off-by: Damien Le Moal

ata: Drop commas after OF match table sentinels

2022-03-07T02:49:10+00:00

It does not make sense to have a comma after a sentinel, as any new
elements must be added before the sentinel.

Add comments to clarify the purpose of the empty elements.
Rewrap entries to a single line to have a consistent style.

Signed-off-by: Geert Uytterhoeven 
Reviewed-by: Sergey Shtylyov 
Acked-by: Florian Fainelli  [ahci_brcm]
Reviewed-by: Kieran Bingham 
Reviewed-by: Linus Walleij 
Signed-off-by: Damien Le Moal

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 45

2019-05-24T15:27:12+00:00

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 or at your option any
  later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 11 file(s).

Signed-off-by: Thomas Gleixner 
Reviewed-by: Kate Stewart 
Reviewed-by: Allison Randal 
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.370933192@linutronix.de
Signed-off-by: Greg Kroah-Hartman

ata: Disable AHCI ALPM feature for Ampere Computing eMAG SATA

2018-09-07T14:32:17+00:00

Due to hardware errata, Ampere Computing eMAG SATA can't support
AHCI ALPM feature. This patch disables the AHCI ALPM feature for
eMAG SATA.

Signed-off-by: Suman Trpathi 
Signed-off-by: Rameshwar Prasad Sahu 
Signed-off-by: Jens Axboe

Merge branch 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

2018-08-24T20:20:33+00:00

Pull libata updates from Tejun Heo:
 "Nothing too interesting. Mostly ahci and ahci_platform changes, many
  around power management"

* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
  ata: ahci_platform: enable to get and control reset
  ata: libahci_platform: add reset control support
  ata: add an extra argument to ahci_platform_get_resources()
  ata: sata_rcar: Add r8a77965 support
  ata: sata_rcar: exclude setting of PHY registers in Gen3
  ata: sata_rcar: really mask all interrupts on Gen2 and later
  Revert "ata: ahci_platform: allow disabling of hotplug to save power"
  ata: libahci: Allow reconfigure of DEVSLP register
  ata: libahci: Correct setting of DEVSLP register
  ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
  ata: ahci: Support state with min power but Partial low power state
  Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
  ata: sata_rcar: Add rudimentary Runtime PM support
  ata: sata_rcar: Provide a short-hand for &pdev->dev
  ata: Only output sg element mapped number in verbose debug
  ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
  ata: ahci_platform: convert kcalloc to devm_kcalloc
  ata: ahci_platform: convert kzallloc to kcalloc
  ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
  libata: remove ata_sff_data_xfer_noirq()
  ...

ata: ahci_platform: enable to get and control reset

2018-08-22T15:08:28+00:00

Unlike SoC-specific driver, generic ahci_platform driver doesn't
have any chances to control resets.

This adds AHCI_PLATFORM_GET_RESETS to ahci_platform_get_resources()
on the generic driver to enable reset control support.

Suggested-by: Hans de Goede 
Cc: Thierry Reding 
Signed-off-by: Kunihiko Hayashi 
Reviewed-by: Hans de Goede 
Signed-off-by: Tejun Heo

ata: add an extra argument to ahci_platform_get_resources()

2018-08-22T15:08:27+00:00

Add an extra argument to ahci_platform_get_resources(), that is
for the bitmap representing the resource to get in this function.

Currently there is no resources to be defined, so all the callers set
'0' to the argument.

Suggested-by: Hans de Goede 
Cc: Thierry Reding 
Cc: Matthias Brugger 
Cc: Patrice Chotard 
Cc: Maxime Ripard 
Signed-off-by: Kunihiko Hayashi 
Reviewed-by: Hans de Goede 
Signed-off-by: Tejun Heo

Revert "ata: ahci_platform: allow disabling of hotplug to save power"

2018-08-06T17:22:35+00:00

This reverts commit aece27a2f01be4bb7683790f69cd1bed3a0929a2.

Causes boot failure on some devices.

 http://lore.kernel.org/r/CA+G9fYuKW_jCFZPqG4tz=QY9ROfHO38KiCp9XTA+KaDOFVtcqQ@mail.gmail.com

Signed-off-by: Tejun Heo

ata: ahci-platform: Remove support for Exynos5440

2018-07-17T17:55:44+00:00

The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.

Signed-off-by: Krzysztof Kozlowski 
Reviewed-by: Rob Herring