linux-stable.git/drivers/ata/Makefile, branch linux-3.8.y

[libata] Makefile: Fix build error in sata_highbank

2012-10-02T02:50:37+00:00

Allow sata_highbank to build even if no other users of libahci.o are built.

Signed-off-by: Mark Langsdorf 
Signed-off-by: Jeff Garzik

ata: add platform driver for Calxeda AHCI controller

2012-09-13T05:09:41+00:00

Calxeda highbank SATA phy has intermittent problems bringing up a link
with Gen3 drives. Retrying the phy hard reset can work-around this issue,
but each reset also disables spread spectrum support. The reset function
also needs to reprogram the phy to enable spread spectrum support.

Create a new driver based on ahci_platform to support the Calxeda Highbank
SATA controller.

Signed-off-by: Mark Langsdorf 
Signed-off-by: Rob Herring 
Signed-off-by: Jeff Garzik

PATA host controller driver for ep93xx

2012-05-22T20:02:34+00:00

Add PATA host controller driver for ep93xx.

Signed-off-by: Rafal Prylowski 
Cc: Joao Ramos 
Cc: H Hartley Sweeten 
Cc: Ryan Mallon 
Cc: Sergei Shtylyov 
Cc: Bartlomiej Zolnierkiewicz 
Signed-off-by: Jeff Garzik

libata: remove no longer needed pata_qdi driver

2011-10-14T17:25:24+00:00

QDI65x0 controllers are fully supported by pata_legacy driver
so remove no longer needed pata_qdi driver.

Leave PATA_QDI config option for compatibility reasons and teach
pata_legacy to preserve the old behavior of pata_qdi driver.

Acked-by: Alan Cox 
Signed-off-by: Bartlomiej Zolnierkiewicz 
Signed-off-by: Jeff Garzik

ata: Add iMX pata support

2011-08-19T03:57:58+00:00

Add basic support for pata on iMX. It has been tested only on imx51.
SDMA support will probably be added later so this version supports only
PIO.

v2:
  - enable only when needed IORDY
  - use dev_get_drvdata
v3:
  - add missing clk_put() calls
  - use platform_get_irq()
  - fix resume code to avoid disabling IORDY on resume
v4:
  - Remove EXPERIMENTAL and switch to depends on ARCH_MXC
  - Use devm_kzalloc()
  - make clock a must-have
  - Use only 1 ioremap

Signed-off-by: Arnaud Patard 
Signed-off-by: Jeff Garzik

pata_arasan_cf: Adding support for arasan compact flash host controller

2011-03-14T06:52:46+00:00

The Arasan CompactFlash Device Controller has three basic modes of
operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card
ATA using true IDE modes.

Currently driver supports only True IDE mode.

Signed-off-by: Viresh Kumar 
Signed-off-by: Jeff Garzik

[libata] new driver acard_ahci, for ATP8620 host controller

2011-01-06T00:43:22+00:00

Add support for Acard ATP8620 host controller.

Based upon initial version by Jeff Garzik.

Signed-off-by: David Milburn 
Signed-off-by: Jeff Garzik

pata_mpc52xx: driver needs BMDMA

2010-12-24T18:33:37+00:00

Found by this build-error if BMDMA is disabled:

drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one':
drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function)
...

Move the Kconfig entry to the proper location as needed since
9a7780c9acb821fe1c2b6fc53f74cc2556ff5364 (libata-sff: make BMDMA optional)

Signed-off-by: Wolfram Sang 
Signed-off-by: Jeff Garzik

Drivers: ata: Makefile: replace the use of -objs with -y

2010-10-22T01:17:32+00:00

Changed -objs to -y in Makefile.

Signed-off-by: Tracey Dent 
Signed-off-by: Jeff Garzik

[libata] Add ATA transport class

2010-10-22T00:21:03+00:00

This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.

Signed-off-by: Gwendal Grignou 
Reviewed-by: Grant Grundler 
Signed-off-by: Jeff Garzik