linux-stable.git/drivers/acpi, branch v5.0.12

Revert "ACPICA: Clear status of GPEs before enabling them"

2019-05-04T07:21:10+00:00

commit 2c2a2fb1e2a9256714338875bede6b7cbd4b9542 upstream.

Revert commit c8b1917c8987 ("ACPICA: Clear status of GPEs before
enabling them") that causes problems with Thunderbolt controllers
to occur if a dock device is connected at init time (the xhci_hcd
and thunderbolt modules crash which prevents peripherals connected
through them from working).

Commit c8b1917c8987 effectively causes commit ecc1165b8b74 ("ACPICA:
Dispatch active GPEs at init time") to get undone, so the problem
addressed by commit ecc1165b8b74 appears again as a result of it.

Fixes: c8b1917c8987 ("ACPICA: Clear status of GPEs before enabling them")
Link: https://lore.kernel.org/lkml/s5hy33siofw.wl-tiwai@suse.de/T/#u
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1132943
Reported-by: Michael Hirmke 
Reported-by: Takashi Iwai 
Cc: 4.17+  # 4.17+
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

nfit/ars: Avoid stale ARS results

2019-04-27T07:37:43+00:00

commit 78153dd45e7e0596ba32b15d02bda08e1513111e upstream.

Gate ARS result consumption on whether the OS issued start-ARS since the
previous consumption. The BIOS may only clear its result buffers after a
successful start-ARS.

Fixes: 0caeef63e6d2 ("libnvdimm: Add a poison list and export badblocks")
Cc: 
Reported-by: Krzysztof Rusocki 
Reported-by: Vishal Verma 
Reviewed-by: Toshi Kani 
Signed-off-by: Dan Williams 
Signed-off-by: Sasha Levin

nfit/ars: Allow root to busy-poll the ARS state machine

2019-04-27T07:37:43+00:00

commit 5479b2757f26fe9908fc341d105b2097fe820b6f upstream.

The ARS implementation implements exponential back-off on the poll
interval to prevent high-frequency access to the DIMM / platform
interface. Depending on when the ARS completes the poll interval may
exceed the completion event by minutes. Allow root to reset the timeout
each time it probes the status. A one-second timeout is still enforced,
but root can otherwise can control the poll interval.

Fixes: bc6ba8085842 ("nfit, address-range-scrub: rework and simplify ARS...")
Cc: 
Reported-by: Erwin Tsaur 
Reviewed-by: Toshi Kani 
Signed-off-by: Dan Williams 
Signed-off-by: Sasha Levin

nfit/ars: Introduce scrub_flags

2019-04-27T07:37:43+00:00

commit e34b8252a3d2893ca55c82dbfcdaa302fa03d400 upstream.

In preparation for introducing new flags to gate whether ARS results are
stale, or poll the completion state, convert the existing flags to an
unsigned long with enumerated values. This conversion allows the flags
to be atomically updated outside of ->init_mutex.

Reviewed-by: Toshi Kani 
Signed-off-by: Dan Williams 
Signed-off-by: Sasha Levin

nfit/ars: Remove ars_start_flags

2019-04-27T07:37:43+00:00

commit 317a992ab9266b86b774b9f6b0f87eb4f59879a1 upstream.

The ars_start_flags property of 'struct acpi_nfit_desc' is no longer
used since ARS_REQ_SHORT and ARS_REQ_LONG were added.

Reviewed-by: Toshi Kani 
Signed-off-by: Dan Williams 
Signed-off-by: Sasha Levin

Revert "ACPI / EC: Remove old CLEAR_ON_RESUME quirk"

2019-04-20T07:17:03+00:00

[ Upstream commit b6a3e1475b0220378ad32bdf4d8692f058b1fc03 ]

On some Samsung hardware, it is necessary to clear events accumulated by
the EC during sleep. These ECs stop reporting GPEs until they are manually
polled, if too many events are accumulated.
Thus the CLEAR_ON_RESUME quirk is introduced to send EC query commands
unconditionally after resume to clear all the EC query events on those
platforms.

Later, commit 4c237371f290 ("ACPI / EC: Remove old CLEAR_ON_RESUME quirk")
removes the CLEAR_ON_RESUME quirk because we thought the new EC IRQ
polling logic should handle this case.

Now it has been proved that the EC IRQ Polling logic does not fix the
issue actually because we got regression report on these Samsung
platforms after removing the quirk.

Thus revert commit 4c237371f290 ("ACPI / EC: Remove old CLEAR_ON_RESUME
quirk") to introduce back the Samsung quirk in this patch.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161
Tested-by: Ortwin Glück 
Tested-by: Francisco Cribari 
Tested-by: Balazs Varga 
Signed-off-by: Zhang Rui 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin

ACPI / utils: Drop reference in test for device presence

2019-04-20T07:16:56+00:00

[ Upstream commit 54e3aca84e571559915998aa6cc05e5ac37c043b ]

When commit 8661423eea1a ("ACPI / utils: Add new acpi_dev_present
helper") introduced acpi_dev_present(), it missed the fact that
bus_find_device() took a reference on the device found by it and
the callers of acpi_dev_present() don't drop that reference.

Drop the reference on the device in acpi_dev_present().

Fixes: 8661423eea1a ("ACPI / utils: Add new acpi_dev_present helper")
Signed-off-by: Andy Shevchenko 
Reviewed-by: Hans de Goede 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin

ACPICA: Namespace: remove address node from global list after method termination

2019-04-17T06:39:47+00:00

commit c5781ffbbd4f742a58263458145fe7f0ac01d9e0 upstream.

ACPICA commit b233720031a480abd438f2e9c643080929d144c3

ASL operation_regions declare a range of addresses that it uses. In a
perfect world, the range of addresses should be used exclusively by
the AML interpreter. The OS can use this information to decide which
drivers to load so that the AML interpreter and device drivers use
different regions of memory.

During table load, the address information is added to a global
address range list. Each node in this list contains an address range
as well as a namespace node of the operation_region. This list is
deleted at ACPI shutdown.

Unfortunately, ASL operation_regions can be declared inside of control
methods. Although this is not recommended, modern firmware contains
such code. New module level code changes unintentionally removed the
functionality of adding and removing nodes to the global address
range list.

A few months ago, support for adding addresses has been re-
implemented. However, the removal of the address range list was
missed and resulted in some systems to crash due to the address list
containing bogus namespace nodes from operation_regions declared in
control methods. In order to fix the crash, this change removes
dynamic operation_regions after control method termination.

Link: https://github.com/acpica/acpica/commit/b2337200
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202475
Fixes: 4abb951b73ff ("ACPICA: AML interpreter: add region addresses in global list during initialization")
Reported-by: Michael J Gruber 
Signed-off-by: Erik Schmauss 
Signed-off-by: Bob Moore 
Cc: 4.20+  # 4.20+
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

ACPICA: Clear status of GPEs before enabling them

2019-04-17T06:39:46+00:00

commit c8b1917c8987a6fa3695d479b4d60fbbbc3e537b upstream.

Commit 18996f2db918 ("ACPICA: Events: Stop unconditionally clearing
ACPI IRQs during suspend/resume") was added to stop clearing event
status bits unconditionally in the system-wide suspend and resume
paths. This was done because of an issue with a laptop lid appaering
to be closed even when it was used to wake up the system from suspend
(see https://bugzilla.kernel.org/show_bug.cgi?id=196249), which
happened because event status bits were cleared unconditionally on
system resume. Though this change fixed the issue in the resume path,
it introduced regressions in a few suspend paths.

First regression was reported and fixed in the S5 entry path by commit
fa85015c0d95 ("ACPICA: Clear status of all events when entering S5").
Next regression was reported and fixed for all legacy sleep paths by
commit f317c7dc12b7 ("ACPICA: Clear status of all events when entering
sleep states").  However, there still is a suspend-to-idle regression,
since suspend-to-idle does not follow the legacy sleep paths.

In the suspend-to-idle case, wakeup is enabled as part of device
suspend.  If the status bits of wakeup GPEs are set when they are
enabled, it causes a premature system wakeup to occur.

To address that problem, partially revert commit 18996f2db918 to
restore GPE status bits clearing before the GPE is enabled in
acpi_ev_enable_gpe().

Fixes: 18996f2db918 ("ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume")
Signed-off-by: Furquan Shaikh 
Cc: 4.17+  # 4.17+
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

ACPI / video: Extend chassis-type detection with a "Lunch Box" check

2019-04-05T20:34:54+00:00

[ Upstream commit d693c008e3ca04db5916ff72e68ce661888a913b ]

Commit 53fa1f6e8a59 ("ACPI / video: Only default only_lcd to true on
Win8-ready _desktops_") introduced chassis type detection, limiting the
lcd_only check for the backlight to devices where the chassis-type
indicates their is no builtin LCD panel.

The purpose of the lcd_only check is to avoid advertising a backlight
interface on desktops, since skylake and newer machines seem to always
have a backlight interface even if there is no LCD panel. The limiting
of this check to desktops only was done to avoid breaking backlight
support on some laptops which do not have the lcd flag set.

The Fujitsu ESPRIMO Q910 which is a compact (NUC like) desktop machine
has a chassis type of 0x10 aka "Lunch Box". Without the lcd_only check
we end up falsely advertising backlight/brightness control on this
device. This commit extend the dmi_is_desktop check to return true
for type 0x10 to fix this.

Fixes: 53fa1f6e8a59 ("ACPI / video: Only default only_lcd to true ...")
Signed-off-by: Hans de Goede 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin