linux-stable.git/drivers/acpi, branch v4.9.162

ACPI: NUMA: Use correct type for printing addresses on i386-PAE

2019-02-20T09:18:28+00:00

[ Upstream commit b9ced18acf68dffebe6888c7ec765a2b1db7a039 ]

The addresses of NUMA nodes are not printed correctly on i386-PAE
which is misleading.

Here is a debian9-32bit with PAE in a QEMU guest having more than 4G
of memory:

qemu-system-i386 \
-hda /var/lib/libvirt/images/debian32.qcow2 \
-m 5G \
-enable-kvm \
-smp 10 \
-numa node,mem=512M,nodeid=0,cpus=0 \
-numa node,mem=512M,nodeid=1,cpus=1 \
-numa node,mem=512M,nodeid=2,cpus=2 \
-numa node,mem=512M,nodeid=3,cpus=3 \
-numa node,mem=512M,nodeid=4,cpus=4 \
-numa node,mem=512M,nodeid=5,cpus=5 \
-numa node,mem=512M,nodeid=6,cpus=6 \
-numa node,mem=512M,nodeid=7,cpus=7 \
-numa node,mem=512M,nodeid=8,cpus=8 \
-numa node,mem=512M,nodeid=9,cpus=9 \
-serial stdio

Because of the wrong value type, it prints as below:

[    0.021049] ACPI: SRAT Memory (0x0 length 0xa0000) in proximity domain 0 enabled
[    0.021740] ACPI: SRAT Memory (0x100000 length 0x1ff00000) in proximity domain 0 enabled
[    0.022425] ACPI: SRAT Memory (0x20000000 length 0x20000000) in proximity domain 1 enabled
[    0.023092] ACPI: SRAT Memory (0x40000000 length 0x20000000) in proximity domain 2 enabled
[    0.023764] ACPI: SRAT Memory (0x60000000 length 0x20000000) in proximity domain 3 enabled
[    0.024431] ACPI: SRAT Memory (0x80000000 length 0x20000000) in proximity domain 4 enabled
[    0.025104] ACPI: SRAT Memory (0xa0000000 length 0x20000000) in proximity domain 5 enabled
[    0.025791] ACPI: SRAT Memory (0x0 length 0x20000000) in proximity domain 6 enabled
[    0.026412] ACPI: SRAT Memory (0x20000000 length 0x20000000) in proximity domain 7 enabled
[    0.027118] ACPI: SRAT Memory (0x40000000 length 0x20000000) in proximity domain 8 enabled
[    0.027802] ACPI: SRAT Memory (0x60000000 length 0x20000000) in proximity domain 9 enabled

The upper half of the start address of the NUMA domains between 6
and 9 inclusive was cut, so the printed values are incorrect.

Fix the value type, to get the correct values in the log as follows:

[    0.023698] ACPI: SRAT Memory (0x0 length 0xa0000) in proximity domain 0 enabled
[    0.024325] ACPI: SRAT Memory (0x100000 length 0x1ff00000) in proximity domain 0 enabled
[    0.024981] ACPI: SRAT Memory (0x20000000 length 0x20000000) in proximity domain 1 enabled
[    0.025659] ACPI: SRAT Memory (0x40000000 length 0x20000000) in proximity domain 2 enabled
[    0.026317] ACPI: SRAT Memory (0x60000000 length 0x20000000) in proximity domain 3 enabled
[    0.026980] ACPI: SRAT Memory (0x80000000 length 0x20000000) in proximity domain 4 enabled
[    0.027635] ACPI: SRAT Memory (0xa0000000 length 0x20000000) in proximity domain 5 enabled
[    0.028311] ACPI: SRAT Memory (0x100000000 length 0x20000000) in proximity domain 6 enabled
[    0.028985] ACPI: SRAT Memory (0x120000000 length 0x20000000) in proximity domain 7 enabled
[    0.029667] ACPI: SRAT Memory (0x140000000 length 0x20000000) in proximity domain 8 enabled
[    0.030334] ACPI: SRAT Memory (0x160000000 length 0x20000000) in proximity domain 9 enabled

Signed-off-by: Chao Fan 
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin

acpi/nfit: Fix command-supported detection

2019-01-31T07:12:35+00:00

commit 11189c1089da413aa4b5fd6be4c4d47c78968819 upstream.

The _DSM function number validation only happens to succeed when the
generic Linux command number translation corresponds with a
DSM-family-specific function number. This breaks NVDIMM-N
implementations that correctly implement _LSR, _LSW, and _LSI, but do
not happen to publish support for DSM function numbers 4, 5, and 6.

Recall that the support for _LS{I,R,W} family of methods results in the
DIMM being marked as supporting those command numbers at
acpi_nfit_register_dimms() time. The DSM function mask is only used for
ND_CMD_CALL support of non-NVDIMM_FAMILY_INTEL devices.

Fixes: 31eca76ba2fc ("nfit, libnvdimm: limited/whitelisted dimm command...")
Cc: 
Link: https://github.com/pmem/ndctl/issues/78
Reported-by: Sujith Pandel 
Tested-by: Sujith Pandel 
Reviewed-by: Vishal Verma 
Reviewed-by: Jeff Moyer 
Signed-off-by: Dan Williams 
Signed-off-by: Greg Kroah-Hartman

acpi/nfit: Block function zero DSMs

2019-01-31T07:12:35+00:00

commit 5e9e38d0db1d29efed1dd4cf9a70115d33521be7 upstream.

In preparation for using function number 0 as an error value, prevent it
from being considered a valid function value by acpi_nfit_ctl().

Cc: 
Cc: stuart hayes 
Fixes: e02fb7264d8a ("nfit: add Microsoft NVDIMM DSM command set...")
Reported-by: Jeff Moyer 
Reviewed-by: Jeff Moyer 
Signed-off-by: Dan Williams 
Signed-off-by: Greg Kroah-Hartman

ACPI: power: Skip duplicate power resource references in _PRx

2019-01-16T21:12:32+00:00

commit 7d7b467cb95bf29597b417d4990160d4ea6d69b9 upstream.

Some ACPI tables contain duplicate power resource references like this:

        Name (_PR0, Package (0x04)  // _PR0: Power Resources for D0
        {
            P28P,
            P18P,
            P18P,
            CLK4
        })

This causes a WARN_ON in sysfs_add_link_to_group() because we end up
adding a link to the same acpi_device twice:

sysfs: cannot create duplicate filename '/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/808622C1:00/OVTI2680:00/power_resources_D0/LNXPOWER:0a'
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.12-301.fc29.x86_64 #1
Hardware name: Insyde CherryTrail/Type2 - Board Product Name, BIOS jumperx.T87.KFBNEEA02 04/13/2016
Call Trace:
 dump_stack+0x5c/0x80
 sysfs_warn_dup.cold.3+0x17/0x2a
 sysfs_do_create_link_sd.isra.2+0xa9/0xb0
 sysfs_add_link_to_group+0x30/0x50
 acpi_power_expose_list+0x74/0xa0
 acpi_power_add_remove_device+0x50/0xa0
 acpi_add_single_object+0x26b/0x5f0
 acpi_bus_check_add+0xc4/0x250
 ...

To address this issue, make acpi_extract_power_resources() check for
duplicates and simply skip them when found.

Cc: All applicable 
Signed-off-by: Hans de Goede 
[ rjw: Subject & changelog, comments ]
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

ACPI / platform: Add SMB0001 HID to forbidden_id_list

2018-11-27T15:09:41+00:00

commit 2bbb5fa37475d7aa5fa62f34db1623f3da2dfdfa upstream.

Many HP AMD based laptops contain an SMB0001 device like this:

Device (SMBD)
{
    Name (_HID, "SMB0001")  // _HID: Hardware ID
    Name (_CRS, ResourceTemplate ()  // _CRS: Current Resource Settings
    {
        IO (Decode16,
            0x0B20,             // Range Minimum
            0x0B20,             // Range Maximum
            0x20,               // Alignment
            0x20,               // Length
            )
        IRQ (Level, ActiveLow, Shared, )
            {7}
    })
}

The legacy style IRQ resource here causes acpi_dev_get_irqresource() to
be called with legacy=true and this message to show in dmesg:
ACPI: IRQ 7 override to edge, high

This causes issues when later on the AMD0030 GPIO device gets enumerated:

Device (GPIO)
{
    Name (_HID, "AMDI0030")  // _HID: Hardware ID
    Name (_CID, "AMDI0030")  // _CID: Compatible ID
    Name (_UID, Zero)  // _UID: Unique ID
    Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
    {
	Name (RBUF, ResourceTemplate ()
	{
	    Interrupt (ResourceConsumer, Level, ActiveLow, Shared, ,, )
	    {
		0x00000007,
	    }
	    Memory32Fixed (ReadWrite,
		0xFED81500,         // Address Base
		0x00000400,         // Address Length
		)
	})
	Return (RBUF) /* \_SB_.GPIO._CRS.RBUF */
    }
}

Now acpi_dev_get_irqresource() gets called with legacy=false, but because
of the earlier override of the trigger-type acpi_register_gsi() returns
-EBUSY (because we try to register the same interrupt with a different
trigger-type) and we end up setting IORESOURCE_DISABLED in the flags.

The setting of IORESOURCE_DISABLED causes platform_get_irq() to call
acpi_irq_get() which is not implemented on x86 and returns -EINVAL.
resulting in the following in dmesg:

amd_gpio AMDI0030:00: Failed to get gpio IRQ: -22
amd_gpio: probe of AMDI0030:00 failed with error -22

The SMB0001 is a "virtual" device in the sense that the only way the OS
interacts with it is through calling a couple of methods to do SMBus
transfers. As such it is weird that it has IO and IRQ resources at all,
because the driver for it is not expected to ever access the hardware
directly.

The Linux driver for the SMB0001 device directly binds to the acpi_device
through the acpi_bus, so we do not need to instantiate a platform_device
for this ACPI device. This commit adds the SMB0001 HID to the
forbidden_id_list, avoiding the instantiating of a platform_device for it.
Not instantiating a platform_device means we will no longer call
acpi_dev_get_irqresource() for the legacy IRQ resource fixing the probe of
the AMDI0030 device failing.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1644013
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198715
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199523
Reported-by: Lukas Kahnert 
Tested-by: Marc 
Cc: All applicable 
Signed-off-by: Hans de Goede 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman

ACPI / watchdog: Prefer iTCO_wdt always when WDAT table uses RTC SRAM

2018-11-27T15:09:40+00:00

[ Upstream commit 5a802a7a285c8877ca872e44eeb0f06afcb5212f ]

After we added quirk for Lenovo Z50-70 it turns out there are at least
two more systems where WDAT table includes instructions accessing RTC
SRAM. Instead of quirking each system separately, look for such
instructions in the table and automatically prefer iTCO_wdt if found.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=199033
Reported-by: Arnold Guy 
Reported-by: Alois Nespor 
Reported-by: Yury Pakin 
Reported-by: Ihor Chyhin 
Signed-off-by: Mika Westerberg 
Acked-by: Guenter Roeck 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin

ACPI / watchdog: Prefer iTCO_wdt on Lenovo Z50-70

2018-11-27T15:09:40+00:00

[ Upstream commit a0a37862a4e1844793d39aca9ccb8fecbdcb8659 ]

WDAT table on Lenovo Z50-70 is using RTC SRAM (ports 0x70 and 0x71) to
store state of the timer. This conflicts with Linux RTC driver
(rtc-cmos.c) who fails to reserve those ports for itself preventing RTC
from functioning. In addition the WDAT table seems not to be fully
functional because it does not reset the system when the watchdog times
out.

On this system iTCO_wdt works just fine so we simply prefer to use it
instead of WDAT. This makes RTC working again and also results working
watchdog via iTCO_wdt.

Reported-by: Peter Milley 
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199033
Signed-off-by: Mika Westerberg 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin

ACPI / LPSS: Add alternative ACPI HIDs for Cherry Trail DMA controllers

2018-11-13T19:16:51+00:00

[ Upstream commit 240714061c58e6b1abfb3322398a7634151c06cb ]

Bay and Cherry Trail DSTDs represent a different set of devices depending
on which OS the device think it is booting. One set of decices for Windows
and another set of devices for Android which targets the Android-x86 Linux
kernel fork (which e.g. used to have its own display driver instead of
using the i915 driver).

Which set of devices we are actually going to get is out of our control,
this is controlled by the ACPI OSID variable, which gets either set through
an EFI setup option, or sometimes is autodetected. So we need to support
both.

This commit adds support for the 80862286 and 808622C0 ACPI HIDs which we
get for the first resp. second DMA controller on Cherry Trail devices when
OSID is set to Android.

Signed-off-by: Hans de Goede 
Reviewed-by: Andy Shevchenko 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ACPI: sysfs: Make ACPI GPE mask kernel parameter cover all GPEs

2018-11-10T15:42:45+00:00

[ Upstream commit 0f27cff8597d86f881ea8274b49b63b678c14a3c ]

The acpi_mask_gpe= kernel parameter documentation states that the range
of mask is 128 GPEs (0x00 to 0x7F).  The acpi_masked_gpes mask is a u64 so
only 64 GPEs (0x00 to 0x3F) can really be masked.

Use a bitmap of size 0xFF instead of a u64 for the GPE mask so 256
GPEs can be masked.

Fixes: 9c4aa1eecb48 (ACPI / sysfs: Provide quirk mechanism to prevent GPE flooding)
Signed-off-by: Prarit Bharava 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin

ACPI / scan: Initialize status to ACPI_STA_DEFAULT

2018-09-15T07:42:59+00:00

[ Upstream commit 5971b0c1594d6c34e257101ed5fdffec65205c50 ]

Since commit 63347db0affa "ACPI / scan: Use acpi_bus_get_status() to
initialize ACPI_TYPE_DEVICE devs" the status field of normal acpi_devices
gets set to 0 by acpi_bus_type_and_status() and filled with its actual
value later when acpi_add_single_object() calls acpi_bus_get_status().

This means that any acpi_match_device_ids() calls in between will always
fail with -ENOENT.

We already have a workaround for this, which temporary forces status to
ACPI_STA_DEFAULT in drivers/acpi/x86/utils.c: acpi_device_always_present()
and the next commit in this series adds another acpi_match_device_ids()
call between status being initialized as 0 and the acpi_bus_get_status()
call.

Rather then adding another workaround, this commit makes
acpi_bus_type_and_status() initialize status to ACPI_STA_DEFAULT, this is
safe to do as the only code looking at status between the initialization
and the acpi_bus_get_status() call is those acpi_match_device_ids() calls.

Note this does mean that we need to (re)set status to 0 in case the
acpi_bus_get_status() call fails.

Signed-off-by: Hans de Goede 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman