Commit 20dacb71ad28 ("ACPI / PM: Rework device power management to follow
ACPI 6") changed the device power management to use D3hot if the device
in question does not have _PR3 method even if D3cold was requested by the
caller.

However, if the device has _PR3 device->power.state is also set to D3hot
instead of D3Cold after power resources have been turned off because
device->power.state will be assigned from "state" instead of
"target_state".

Next time the device is transitioned to D0, acpi_power_transition() will
find that the current power state of the device is D3hot instead of D3cold
which causes it to power down all resources required for the current
(wrong) state D3hot.

Below is a simplified ASL example of a real touch panel device which
triggers the problem:

  Scope (TPL1)
  {
      Name (_PR0, Package (1) { \_SB.PCI0.I2C1.PXTC })
      Name (_PR3, Package (1) { \_SB.PCI0.I2C1.PXTC })
      ...
  }

In both D0 and D3hot the same power resource is required. However, when
acpi_power_transition() turns off power resources required for D3hot (as
the device is transitioned to D0) it powers down PXTC which then makes the
device to lose its power.

Fix this by assigning "target_state" to the device power state instead of
"state" that is always D3hot even for devices with valid _PR3.

Fixes: 20dacb71ad28 (ACPI / PM: Rework device power management to follow ACPI 6)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add missing invocation of pm_generic_complete() to
acpi_subsys_complete() to allow ->complete callbacks provided
by the drivers of devices using the ACPI PM domain to be executed
during system resume.

Fixes: f25c0ae2b4c4 (ACPI / PM: Avoid resuming devices in ACPI PM domain during system suspend)
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The ACPI 6 specification has made some changes in the device power
management area.  In particular:

 * The D3hot power state is now supposed to be always available
   (instead of D3cold) and D3cold is only regarded as valid if the
   _PR3 object is present for the given device.

 * The required ordering of transitions into power states deeper than
   D0 is now such that for a transition into state Dx the _PSx method
   is supposed to be executed first, if present, and the states of
   the power resources the device depends on are supposed to be
   changed after that.

 * It is now explicitly forbidden to transition devices from
   lower-power (deeper) into higher-power (shallower) power states
   other than D0.

Those changes have been made so the specification reflects the
Windows' device power management code that the vast majority of
systems using ACPI is validated against.

To avoid artificial differences in ACPI device power management
between Windows and Linux, modify the ACPI device power management
code to follow the new specification.  Add comments explaining the
code flow in some unclear places.

This only may affect some real corner cases in which the OS behavior
expected by the firmware is different from the Windows one, but that's
quite unlikely.  The transition ordering change affects transitions
to D1 and D2 which are rarely used (if at all) and into D3hot and
D3cold for devices actually having _PR3, but those are likely to
be validated against Windows anyway.  The other changes may affect
code calling acpi_device_get_power() or acpi_device_update_power()
where ACPI_STATE_D3_HOT may be returned instead of ACPI_STATE_D3_COLD
(that's why the ACPI fan driver needs to be updated too) and since
transitions into ACPI_STATE_D3_HOT may remove power now, it is better
to avoid this one in acpi_pm_device_sleep_state() if the "no power
off" PM QoS flag is set.

The only existing user of acpi_device_can_poweroff() really cares
about the case when _PR3 is present, so the change in that function
should not cause any problems to happen too.

A plus is that PCI_D3hot can be mapped to ACPI_STATE_D3_HOT
now and the compatibility with older systems should be covered
automatically.

In any case, if any real problems result from this, it still will
be better to follow the Windows' behavior (which now is reflected
by the specification too) in general and handle the cases when it
doesn't work via quirks.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In commit 5de21bb998b8 ("ACPI / PM: Drop CONFIG_PM_RUNTIME from the
ACPI core"), all occurrences of CONFIG_PM_RUNTIME were replaced with
CONFIG_PM. This created the following structure of #ifdef blocks in
the code:

 [...]
 #ifdef CONFIG_PM
 #ifdef CONFIG_PM
 /* always on / undead */
 #ifdef CONFIG_PM_SLEEP
 [...]
 #endif
 #endif
 [...]
 #endif

This patch removes the inner "#ifdef CONFIG_PM" block as it will
always be enabled when the outer block is enabled. This inconsistency
was found using the undertaker-checkpatch tool.

Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

If an ACPI device object whose _STA returns 0 (not present and not
functional) has _PR0 or _PS0, its power_manageable flag will be set
and acpi_bus_init_power() will return 0 for it.  Consequently, if
such a device object is passed to the ACPI device PM functions, they
will attempt to carry out the requested operation on the device,
although they should not do that for devices that are not present.

To fix that problem make acpi_bus_init_power() return an error code
for devices that are not present which will cause power_manageable to
be cleared for them as appropriate in acpi_bus_get_power_flags().
However, the lists of power resources should not be freed for the
device in that case, so modify acpi_bus_get_power_flags() to keep
those lists even if acpi_bus_init_power() returns an error.
Accordingly, when deciding whether or not the lists of power
resources need to be freed, acpi_free_power_resources_lists()
should check the power.flags.power_resources flag instead of
flags.power_manageable, so make that change too.

Furthermore, if acpi_bus_attach() sees that flags.initialized is
unset for the given device, it should reset the power management
settings of the device and re-initialize them from scratch instead
of relying on the previous settings (the device may have appeared
after being not present previously, for example), so make it use
the 'valid' flag of the D0 power state as the initial value of
flags.power_manageable for it and call acpi_bus_init_power() to
discover its current power state.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+

* acpi-scan:
  ACPI / scan: Change the level of _DEP-related messages to KERN_DEBUG

* acpi-utils:
  ACPI / utils: Drop error messages from acpi_evaluate_reference()

* acpi-pm:
  ACPI / PM: Do not disable wakeup GPEs that have not been enabled

In some cases acpi_device_wakeup() may be called to ensure wakeup
power to be off for a given device even though that device's wakeup
GPE has not been enabled so far.  It calls acpi_disable_gpe() on a
GPE that's not enabled and this causes ACPICA to return the AE_LIMIT
status code from that call which then is reported as an error by the
ACPICA's debug facilities (if enabled).  This may lead to a fair
amount of confusion, so introduce a new ACPI device wakeup flag
to store the wakeup GPE status and avoid disabling wakeup GPEs
that have not been enabled.

Reported-and-tested-by: Venkat Raghavulu <venkat.raghavulu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

* pm-runtime: (25 commits)
  i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
  dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
  MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
  block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
  PM: Merge the SET*_RUNTIME_PM_OPS() macros
  PM / Kconfig: Do not select PM directly from Kconfig files
  PCI / PM: Drop CONFIG_PM_RUNTIME from the PCI core
  ...

After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM in the ACPI core code.

Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>