linux-stable.git/arch/x86/entry, branch linux-5.2.y

x86/entry/64: Use JMP instead of JMPQ

2019-08-06T17:08:22+00:00

commit 64dbc122b20f75183d8822618c24f85144a5a94d upstream

Somehow the swapgs mitigation entry code patch ended up with a JMPQ
instruction instead of JMP, where only the short jump is needed.  Some
assembler versions apparently fail to optimize JMPQ into a two-byte JMP
when possible, instead always using a 7-byte JMP with relocation.  For
some reason that makes the entry code explode with a #GP during boot.

Change it back to "JMP" as originally intended.

Fixes: 18ec54fdd6d1 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations")
Signed-off-by: Josh Poimboeuf 
Signed-off-by: Thomas Gleixner 
Signed-off-by: Greg Kroah-Hartman

x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations

2019-08-06T17:08:22+00:00

commit 18ec54fdd6d18d92025af097cd042a75cf0ea24c upstream

Spectre v1 isn't only about array bounds checks.  It can affect any
conditional checks.  The kernel entry code interrupt, exception, and NMI
handlers all have conditional swapgs checks.  Those may be problematic in
the context of Spectre v1, as kernel code can speculatively run with a user
GS.

For example:

	if (coming from user space)
		swapgs
	mov %gs:, %reg
	mov (%reg), %reg1

When coming from user space, the CPU can speculatively skip the swapgs, and
then do a speculative percpu load using the user GS value.  So the user can
speculatively force a read of any kernel value.  If a gadget exists which
uses the percpu value as an address in another load/store, then the
contents of the kernel value may become visible via an L1 side channel
attack.

A similar attack exists when coming from kernel space.  The CPU can
speculatively do the swapgs, causing the user GS to get used for the rest
of the speculative window.

The mitigation is similar to a traditional Spectre v1 mitigation, except:

  a) index masking isn't possible; because the index (percpu offset)
     isn't user-controlled; and

  b) an lfence is needed in both the "from user" swapgs path and the
     "from kernel" non-swapgs path (because of the two attacks described
     above).

The user entry swapgs paths already have SWITCH_TO_KERNEL_CR3, which has a
CR3 write when PTI is enabled.  Since CR3 writes are serializing, the
lfences can be skipped in those cases.

On the other hand, the kernel entry swapgs paths don't depend on PTI.

To avoid unnecessary lfences for the user entry case, create two separate
features for alternative patching:

  X86_FEATURE_FENCE_SWAPGS_USER
  X86_FEATURE_FENCE_SWAPGS_KERNEL

Use these features in entry code to patch in lfences where needed.

The features aren't enabled yet, so there's no functional change.

Signed-off-by: Josh Poimboeuf 
Signed-off-by: Thomas Gleixner 
Reviewed-by: Dave Hansen 
Signed-off-by: Greg Kroah-Hartman

xen/pv: Fix a boot up hang revealed by int3 self test

2019-08-06T17:08:13+00:00

[ Upstream commit b23e5844dfe78a80ba672793187d3f52e4b528d7 ]

Commit 7457c0da024b ("x86/alternatives: Add int3_emulate_call()
selftest") is used to ensure there is a gap setup in int3 exception stack
which could be used for inserting call return address.

This gap is missed in XEN PV int3 exception entry path, then below panic
triggered:

[    0.772876] general protection fault: 0000 [#1] SMP NOPTI
[    0.772886] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.2.0+ #11
[    0.772893] RIP: e030:int3_magic+0x0/0x7
[    0.772905] RSP: 3507:ffffffff82203e98 EFLAGS: 00000246
[    0.773334] Call Trace:
[    0.773334]  alternative_instructions+0x3d/0x12e
[    0.773334]  check_bugs+0x7c9/0x887
[    0.773334]  ? __get_locked_pte+0x178/0x1f0
[    0.773334]  start_kernel+0x4ff/0x535
[    0.773334]  ? set_init_arg+0x55/0x55
[    0.773334]  xen_start_kernel+0x571/0x57a

For 64bit PV guests, Xen's ABI enters the kernel with using SYSRET, with
%rcx/%r11 on the stack. To convert back to "normal" looking exceptions,
the xen thunks do 'xen_*: pop %rcx; pop %r11; jmp *'.

E.g. Extracting 'xen_pv_trap xenint3' we have:
xen_xenint3:
 pop %rcx;
 pop %r11;
 jmp xenint3

As xenint3 and int3 entry code are same except xenint3 doesn't generate
a gap, we can fix it by using int3 and drop useless xenint3.

Signed-off-by: Zhenzhong Duan 
Reviewed-by: Juergen Gross 
Cc: Boris Ostrovsky 
Cc: Juergen Gross 
Cc: Stefano Stabellini 
Cc: Andy Lutomirski 
Cc: Peter Zijlstra 
Cc: Thomas Gleixner 
Cc: Ingo Molnar 
Cc: Borislav Petkov 
Cc: Andrew Cooper 
Signed-off-by: Juergen Gross 
Signed-off-by: Sasha Levin

x86/entry/32: Fix ENDPROC of common_spurious

2019-07-21T07:00:44+00:00

[ Upstream commit 1cbec37b3f9cff074a67bef4fc34b30a09958a0a ]

common_spurious is currently ENDed erroneously. common_interrupt is used
in its ENDPROC. So fix this mistake.

Found by my asm macros rewrite patchset.

Fixes: f8a8fe61fec8 ("x86/irq: Seperate unused system vectors from spurious entry again")
Signed-off-by: Jiri Slaby 
Signed-off-by: Thomas Gleixner 
Link: https://lkml.kernel.org/r/20190709063402.19847-1-jslaby@suse.cz
Signed-off-by: Sasha Levin

x86/irq: Seperate unused system vectors from spurious entry again

2019-07-21T07:00:41+00:00

commit f8a8fe61fec8006575699559ead88b0b833d5cad upstream.

Quite some time ago the interrupt entry stubs for unused vectors in the
system vector range got removed and directly mapped to the spurious
interrupt vector entry point.

Sounds reasonable, but it's subtly broken. The spurious interrupt vector
entry point pushes vector number 0xFF on the stack which makes the whole
logic in __smp_spurious_interrupt() pointless.

As a consequence any spurious interrupt which comes from a vector != 0xFF
is treated as a real spurious interrupt (vector 0xFF) and not
acknowledged. That subsequently stalls all interrupt vectors of equal and
lower priority, which brings the system to a grinding halt.

This can happen because even on 64-bit the system vector space is not
guaranteed to be fully populated. A full compile time handling of the
unused vectors is not possible because quite some of them are conditonally
populated at runtime.

Bring the entry stubs back, which wastes 160 bytes if all stubs are unused,
but gains the proper handling back. There is no point to selectively spare
some of the stubs which are known at compile time as the required code in
the IDT management would be way larger and convoluted.

Do not route the spurious entries through common_interrupt and do_IRQ() as
the original code did. Route it to smp_spurious_interrupt() which evaluates
the vector number and acts accordingly now that the real vector numbers are
handed in.

Fixup the pr_warn so the actual spurious vector (0xff) is clearly
distiguished from the other vectors and also note for the vectored case
whether it was pending in the ISR or not.

 "Spurious APIC interrupt (vector 0xFF) on CPU#0, should never happen."
 "Spurious interrupt vector 0xed on CPU#1. Acked."
 "Spurious interrupt vector 0xee on CPU#1. Not pending!."

Fixes: 2414e021ac8d ("x86: Avoid building unused IRQ entry stubs")
Reported-by: Jan Kiszka 
Signed-off-by: Thomas Gleixner 
Cc: Marc Zyngier 
Cc: Jan Beulich 
Link: https://lkml.kernel.org/r/20190628111440.550568228@linutronix.de
Signed-off-by: Greg Kroah-Hartman

x86/vdso: Prevent segfaults due to hoisted vclock reads

2019-06-21T20:31:52+00:00

GCC 5.5.0 sometimes cleverly hoists reads of the pvclock and/or hvclock
pages before the vclock mode checks.  This creates a path through
vclock_gettime() in which no vclock is enabled at all (due to disabled
TSC on old CPUs, for example) but the pvclock or hvclock page
nevertheless read.  This will segfault on bare metal.

This fixes commit 459e3a21535a ("gcc-9: properly declare the
{pv,hv}clock_page storage") in the sense that, before that commit, GCC
didn't seem to generate the offending code.  There was nothing wrong
with that commit per se, and -stable maintainers should backport this to
all supported kernels regardless of whether the offending commit was
present, since the same crash could just as easily be triggered by the
phase of the moon.

On GCC 9.1.1, this doesn't seem to affect the generated code at all, so
I'm not too concerned about performance regressions from this fix.

Cc: stable@vger.kernel.org
Cc: x86@kernel.org
Cc: Borislav Petkov 
Reported-by: Duncan Roe 
Signed-off-by: Andy Lutomirski 
Signed-off-by: Linus Torvalds

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 474

2019-06-19T15:09:11+00:00

Based on 1 normalized pattern(s):

  subject to the gnu public license v 2 no warranty of any kind

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 2 file(s).

Signed-off-by: Thomas Gleixner 
Reviewed-by: Enrico Weigelt 
Reviewed-by: Allison Randal 
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081203.641025917@linutronix.de
Signed-off-by: Greg Kroah-Hartman

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 257

2019-06-05T15:30:27+00:00

Based on 1 normalized pattern(s):

  gpl v2

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 19 file(s).

Signed-off-by: Thomas Gleixner 
Reviewed-by: Allison Randal 
Reviewed-by: Richard Fontana 
Reviewed-by: Steve Winslow 
Reviewed-by: Kate Stewart 
Reviewed-by: Alexios Zavras 
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141333.108140152@linutronix.de
Signed-off-by: Greg Kroah-Hartman

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223

2019-05-30T18:29:55+00:00

Based on 1 normalized pattern(s):

  subject to the gnu public license v 2

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 9 file(s).

Signed-off-by: Thomas Gleixner 
Reviewed-by: Allison Randal 
Reviewed-by: Alexios Zavras 
Reviewed-by: Steve Winslow 
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171440.130801526@linutronix.de
Signed-off-by: Greg Kroah-Hartman

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214

2019-05-30T18:29:54+00:00

Based on 1 normalized pattern(s):

  subject to the gpl v 2

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 2 file(s).

Signed-off-by: Thomas Gleixner 
Reviewed-by: Allison Randal 
Reviewed-by: Steve Winslow 
Reviewed-by: Alexios Zavras 
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171439.372657724@linutronix.de
Signed-off-by: Greg Kroah-Hartman