linux-stable.git/arch/sh, branch v4.4.271

sh: dma: fix kconfig dependency for G2_DMA

2021-01-30T12:25:56+00:00

commit f477a538c14d07f8c45e554c8c5208d588514e98 upstream.

When G2_DMA is enabled and SH_DMA is disabled, it results in the following
Kbuild warning:

WARNING: unmet direct dependencies detected for SH_DMA_API
  Depends on [n]: SH_DMA [=n]
  Selected by [y]:
  - G2_DMA [=y] && SH_DREAMCAST [=y]

The reason is that G2_DMA selects SH_DMA_API without depending on or
selecting SH_DMA while SH_DMA_API depends on SH_DMA.

When G2_DMA was first introduced with commit 40f49e7ed77f
("sh: dma: Make G2 DMA configurable."), this wasn't an issue since
SH_DMA_API didn't have such dependency, and this way was the only way to
enable it since SH_DMA_API was non-visible. However, later SH_DMA_API was
made visible and dependent on SH_DMA with commit d8902adcc1a9
("dmaengine: sh: Add Support SuperH DMA Engine driver").

Let G2_DMA depend on SH_DMA_API instead to avoid Kbuild issues.

Fixes: d8902adcc1a9 ("dmaengine: sh: Add Support SuperH DMA Engine driver")
Signed-off-by: Necip Fazil Yildiran 
Signed-off-by: Rich Felker 
Signed-off-by: Greg Kroah-Hartman

sh: landisk: Add missing initialization of sh_io_port_base

2020-08-21T08:53:07+00:00

[ Upstream commit 0c64a0dce51faa9c706fdf1f957d6f19878f4b81 ]

The Landisk setup code maps the CF IDE area using ioremap_prot(), and
passes the resulting virtual addresses to the pata_platform driver,
disguising them as I/O port addresses.  Hence the pata_platform driver
translates them again using ioport_map().
As CONFIG_GENERIC_IOMAP=n, and CONFIG_HAS_IOPORT_MAP=y, the
SuperH-specific mapping code in arch/sh/kernel/ioport.c translates
I/O port addresses to virtual addresses by adding sh_io_port_base, which
defaults to -1, thus breaking the assumption of an identity mapping.

Fix this by setting sh_io_port_base to zero.

Fixes: 37b7a97884ba64bf ("sh: machvec IO death.")
Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Rich Felker 
Signed-off-by: Sasha Levin

sh: Fix validation of system call number

2020-08-21T08:52:53+00:00

[ Upstream commit 04a8a3d0a73f51c7c2da84f494db7ec1df230e69 ]

The slow path for traced system call entries accessed a wrong memory
location to get the number of the maximum allowed system call number.
Renumber the numbered "local" label for the correct location to avoid
collisions with actual local labels.

Signed-off-by: Michael Karcher 
Tested-by: John Paul Adrian Glaubitz 
Fixes: f3a8308864f920d2 ("sh: Add a few missing irqflags tracing markers.")
Signed-off-by: Rich Felker 
Signed-off-by: Sasha Levin

pinctrl: sh-pfc: sh7269: Fix CAN function GPIOs

2020-02-28T14:39:01+00:00

[ Upstream commit 02aeb2f21530c98fc3ca51028eda742a3fafbd9f ]

pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.

A closer look reveals other issues:
  - Some functionality is available on alternative pins, but the
    PINMUX_DATA() entries is using the wrong marks,
  - Several configurations are missing.

Fix this by:
  - Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
    CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
    resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
    corresponding enum IDs,
  - Adding all missing enum IDs and marks,
  - Use the right (*_PJ2x) variants for alternative pins,
  - Adding all missing configurations to pinmux_data[],
  - Adding all missing function GPIO definitions to pinmux_func_gpios[].

See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
  [1] Table 1.4 List of Pins
  [2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
      Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
      (32 Mailboxes × 1 Channel),
  [3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
      One Channel (96 Mailboxes × 1 Channel),
  [4] Table 48.3 Multiplexed Pins (Port B),
  [5] Table 48.4 Multiplexed Pins (Port C),
  [6] Table 48.10 Multiplexed Pins (Port J),
  [7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).

Signed-off-by: Geert Uytterhoeven 
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
Signed-off-by: Sasha Levin

pinctrl: sh-pfc: sh7734: Fix duplicate TCLK1_B

2020-01-04T12:34:14+00:00

[ Upstream commit 884caadad128efad8e00c1cdc3177bc8912ee8ec ]

The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.

Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.

Reported-by: Ben Dooks 
Signed-off-by: Geert Uytterhoeven 
Link: https://lore.kernel.org/r/20191024131308.16659-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin

sh: kernel: hw_breakpoint: Fix missing break in switch statement

2019-08-25T08:52:55+00:00

commit 1ee1119d184bb06af921b48c3021d921bbd85bac upstream.

Add missing break statement in order to prevent the code from falling
through to case SH_BREAKPOINT_WRITE.

Fixes: 09a072947791 ("sh: hw-breakpoints: Add preliminary support for SH-4A UBC.")
Cc: stable@vger.kernel.org
Reviewed-by: Geert Uytterhoeven 
Reviewed-by: Guenter Roeck 
Tested-by: Guenter Roeck 
Signed-off-by: Gustavo A. R. Silva 
Signed-off-by: Greg Kroah-Hartman

sh: prevent warnings when using iounmap

2019-08-04T07:34:59+00:00

[ Upstream commit 733f0025f0fb43e382b84db0930ae502099b7e62 ]

When building drm/exynos for sh, as part of an allmodconfig build, the
following warning triggered:

  exynos7_drm_decon.c: In function `decon_remove':
  exynos7_drm_decon.c:769:24: warning: unused variable `ctx'
    struct decon_context *ctx = dev_get_drvdata(&pdev->dev);

The ctx variable is only used as argument to iounmap().

In sh - allmodconfig CONFIG_MMU is not defined
so it ended up in:

\#define __iounmap(addr)	do { } while (0)
\#define iounmap		__iounmap

Fix the warning by introducing a static inline function for iounmap.

This is similar to several other architectures.

Link: http://lkml.kernel.org/r/20190622114208.24427-1-sam@ravnborg.org
Signed-off-by: Sam Ravnborg 
Reviewed-by: Geert Uytterhoeven 
Cc: Yoshinori Sato 
Cc: Rich Felker 
Cc: Will Deacon 
Cc: Mark Brown 
Cc: Inki Dae 
Cc: Krzysztof Kozlowski 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds 
Signed-off-by: Sasha Levin

mm: replace get_user_pages_unlocked() write/force parameters with gup_flags

2018-12-17T20:55:16+00:00

commit c164154f66f0c9b02673f07aa4f044f1d9c70274 upstream.

This removes the 'write' and 'force' use from get_user_pages_unlocked()
and replaces them with 'gup_flags' to make the use of FOLL_FORCE
explicit in callers as use of this flag can result in surprising
behaviour (and hence bugs) within the mm subsystem.

Signed-off-by: Lorenzo Stoakes 
Reviewed-by: Jan Kara 
Acked-by: Michal Hocko 
Signed-off-by: Linus Torvalds 
[bwh: Backported to 4.4:
 - Also update calls from process_vm_rw_single_vec() and async_pf_execute()
 - Adjust context]
Signed-off-by: Ben Hutchings 
Signed-off-by: Greg Kroah-Hartman

sh: New gcc support

2018-06-06T14:46:20+00:00

commit 940d4113f3306e07a1f86541489b686d1a979d54 upstream.

New gcc (4.8 or later) used new shift helper functions.
So we need added new helper to private libgcc.

Signed-off-by: Yoshinori Sato 
Signed-off-by: Rich Felker 
Cc: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman

sh: fix debug trap failure to process signals before return to user

2018-05-30T05:49:07+00:00

[ Upstream commit 96a598996f6ac518ac79839ecbb17c91af91f4f7 ]

When responding to a debug trap (breakpoint) in userspace, the
kernel's trap handler raised SIGTRAP but returned from the trap via a
code path that ignored pending signals, resulting in an infinite loop
re-executing the trapping instruction.

Signed-off-by: Rich Felker 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman