linux-stable.git/arch/powerpc/kernel, branch v3.4.7

powerpc: Fix build of some debug irq code

2012-07-16T16:03:49+00:00

commit 21b2de341270bd7bb7a811027ffe63276d9b3b75 upstream.

There was a typo, checking for CONFIG_TRACE_IRQFLAG instead of
CONFIG_TRACE_IRQFLAGS causing some useful debug code to not be
built

This in turns causes a build error on BookE 64-bit due to incorrect
semicolons at the end of a couple of macros, so let's fix that too

Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc: More fixes for lazy IRQ vs. idle

2012-07-16T16:03:49+00:00

commit be2cf20a5ad31ebb13562c1c866ecc626fbd721e upstream.

Looks like we still have issues with pSeries and Cell idle code
vs. the lazy irq state. In fact, the reset fixes that went upstream
are exposing the problem more by causing BUG_ON() to trigger (which
this patch turns into a WARN_ON instead).

We need to be careful when using a variant of low power state that
has the side effect of turning interrupts back on, to properly set
all the SW & lazy state to look as if everything is enabled before
we enter the low power state with MSR:EE off as we will return with
MSR:EE on. If not, we have a discrepancy of state which can cause
things to go very wrong later on.

This patch moves the logic into a helper and uses it from the
pseries and cell idle code. The power4/970 idle code already got
things right (in assembly even !) so I'm not touching it. The power7
"bare metal" idle code is subtly different and correct. Remains PA6T
and some hypervisor based Cell platforms which have questionable
code in there, but they are mostly dead platforms so I'll fix them
when I manage to get final answers from the respective maintainers
about how the low power state actually works on them.

Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc/ftrace: Do not trace restore_interrupts()

2012-07-16T16:03:21+00:00

commit 2d773aa4810d4a612d1c879faacc38594cc3f841 upstream.

As I was adding code that affects all archs, I started testing function
tracer against PPC64 and found that it currently locks up with 3.4
kernel. I figured it was due to tracing a function that shouldn't be, so
I went through the following process to bisect to find the culprit:

 cat /debug/tracing/available_filter_functions > t
 num=`wc -l t`
 sed -ne "1,${num}p" t > t1
 let num=num+1
 sed -ne "${num},$p" t > t2
 cat t1 > /debug/tracing/set_ftrace_filter
 echo function /debug/tracing/current_tracer
 

It finally came down to this function: restore_interrupts()

I'm not sure why this locks up the system. It just seems to prevent
scheduling from occurring. Interrupts seem to still work, as I can ping
the box. But all user processes freeze.

When restore_interrupts() is not traced, function tracing works fine.

Signed-off-by: Steven Rostedt 
Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc: Fix kernel panic during kernel module load

2012-06-17T18:21:22+00:00

commit 3c75296562f43e6fbc6cddd3de948a7b3e4e9bcf upstream.

This fixes a problem which can causes kernel oopses while loading
a kernel module.

According to the PowerPC EABI specification, GPR r11 is assigned
the dedicated function to point to the previous stack frame.
In the powerpc-specific kernel module loader, do_plt_call()
(in arch/powerpc/kernel/module_32.c), GPR r11 is also used
to generate trampoline code.

This combination crashes the kernel, in the case where the compiler
chooses to use a helper function for saving GPRs on entry, and the
module loader has placed the .init.text section far away from the
.text section, meaning that it has to generate a trampoline for
functions in the .init.text section to call the GPR save helper.
Because the trampoline trashes r11, references to the stack frame
using r11 can cause an oops.

The fix just uses GPR r12 instead of GPR r11 for generating the
trampoline code.  According to the statements from Freescale, this is
safe from an EABI perspective.

I've tested the fix for kernel 2.6.33 on MPC8541.

Signed-off-by: Steffen Rumler 
[paulus@samba.org: reworded the description]
Signed-off-by: Paul Mackerras 
Signed-off-by: Greg Kroah-Hartman

powerpc/time: Sanity check of decrementer expiration is necessary

2012-06-17T18:21:22+00:00

commit 860aed25a1f0936d4852ab936252b47cd1e630f1 upstream.

This reverts 68568add2c ("powerpc/time: Remove unnecessary sanity check
of decrementer expiration").  We do need to check whether we have reached
the expiration time of the next event, because we sometimes get an early
decrementer interrupt, most notably when we set the decrementer to 1 in
arch_irq_work_raise().  The effect of not having the sanity check is that
if timer_interrupt() gets called early, we leave the decrementer set to
its maximum value, which means we then don't get any more decrementer
interrupts for about 4 seconds (or longer, depending on timebase
frequency).  I saw these pauses as a consequence of getting a stray
hypervisor decrementer interrupt left over from exiting a KVM guest.

This isn't quite a straight revert because of changes to the surrounding
code, but it restores the same algorithm as was previously used.

Acked-by: Anton Blanchard 
Acked-by: Benjamin Herrenschmidt 
Signed-off-by: Paul Mackerras 
Signed-off-by: Greg Kroah-Hartman

powerpc: Fix broken cpu_idle_wait() implementation

2012-06-01T07:18:16+00:00

commit 9cd75e13de2dcf32ecc21c7f277cff3c0ced059e upstream.

commit 771dae818 (powerpc/cpuidle: Add cpu_idle_wait() to allow
switching of idle routines) implemented cpu_idle_wait() for powerpc.

The changelog says:
 "The equivalent routine for x86 is in arch/x86/kernel/process.c
  but the powerpc implementation is different.":

Unfortunately the changelog is completely useless as it does not tell
_WHY_ it is different.

Aside of being different the implementation is patently wrong.

The rescheduling IPI is async. That means that there is no guarantee,
that the other cores have executed the IPI when cpu_idle_wait()
returns. But that's the whole purpose of this function: to guarantee
that no CPU uses the old idle handler anymore.

Use the smp_functional_call() based implementation, which fulfils the
requirements.

[ This code is going to replaced by a core version to remove all the
  pointless copies in arch/*, but this one should go to stable ]

Signed-off-by: Thomas Gleixner 
Acked-by: Peter Zijlstra 
Cc: Deepthi Dharwar 
Cc: Trinabh Gupta 
Cc: Arun R Bharadwaj 
Acked-by: Benjamin Herrenschmidt 
Link: http://lkml.kernel.org/r/20120507175651.980164748@linutronix.de
Signed-off-by: Greg Kroah-Hartman

powerpc/irq: Fix another case of lazy IRQ state getting out of sync

2012-05-11T23:40:41+00:00

So we have another case of paca->irq_happened getting out of
sync with the HW irq state. This can happen when a perfmon
interrupt occurs while soft disabled, as it will return to a
soft disabled but hard enabled context while leaving a stale
PACA_IRQ_HARD_DIS flag set.

This patch fixes it, and also adds a test for the condition
of those flags being out of sync in arch_local_irq_restore()
when CONFIG_TRACE_IRQFLAGS is enabled.

This helps catching those gremlins faster (and so far I
can't seem see any anymore, so that's good news).

Signed-off-by: Benjamin Herrenschmidt

powerpc/irq: Make alignment & program interrupt behave the same

2012-05-08T23:42:33+00:00

Alignment was the last user of the ENABLE_INTS macro, which we can
now remove. All non-syscall exceptions now disable interrupts on
entry, they get re-enabled conditionally from C code. Don't
unconditionally re-enable in program check either, check the
original context.

Signed-off-by: Benjamin Herrenschmidt

powerpc/irq: Fix bug with new lazy IRQ handling code

2012-05-08T23:42:21+00:00

We had a case where we could turn on hard interrupts while
leaving the PACA_IRQ_HARD_DIS bit set in the PACA. This can
in turn cause a BUG_ON() to hit in __check_irq_replay() due
to interrupt state getting out of sync.

The assembly code was also way too convoluted. Instead, we
now leave it to the C code to do the right thing which ends
up being smaller and more readable.

Signed-off-by: Benjamin Herrenschmidt

powerpc/irqdomain: Fix broken NR_IRQ references

2012-04-30T00:45:26+00:00

The switch from using irq_map to irq_alloc_desc*() for managing irq
number allocations introduced new bugs in some of the powerpc
interrupt code.  Several functions rely on the value of NR_IRQS to
determine the maximum irq number that could get allocated.  However,
with sparse_irq and using irq_alloc_desc*() the maximum possible irq
number is now specified with 'nr_irqs' which may be a number larger
than NR_IRQS.  This has caused breakage on powermac when
CONFIG_NR_IRQS is set to 32.

This patch removes most of the direct references to NR_IRQS in the
powerpc code and replaces them with either a nr_irqs reference or by
using the common for_each_irq_desc() macro.  The powerpc-specific
for_each_irq() macro is removed at the same time.

Also, the Cell axon_msi driver is refactored to remove the global
build assumption on the size of NR_IRQS and instead add a limit to the
maximum irq number when calling irq_domain_add_nomap().

Signed-off-by: Grant Likely 
Signed-off-by: Benjamin Herrenschmidt