linux-stable.git/arch/powerpc/kernel/entry_32.S, branch v3.2

powerpc/trace: Add a dummy stack frame for trace_hardirqs_off

2011-11-16T03:47:54+00:00

The trace_hardirqs_off will use CALLER_ADDR0 and CALLER_ADDR1.
If an exception occurs in user mode, there is only one stack frame
on the stack and accessing the CALLER_ADDR1 will causes the following
call trace. So we create a dummy stack frame to make
trace_hardirqs_off happy.

WARNING: at kernel/smp.c:459
Modules linked in:
NIP: c0093280 LR: c00930a0 CTR: c0010780
REGS: edb87ae0 TRAP: 0700   Not tainted  (3.1.0)
MSR: 00021002   CR: 28002888  XER: 00000000
TASK = edce2ac0[17658] 'mthread-lock-on' THREAD: edb86000 CPU: 5
GPR00: 00000001 edb87b90 edce2ac0 00000005 c0019594 edb87bd8 00000001 00000fe3
GPR08: 00041000 c084138c 4e20120d edb87b90 48002888 1001aa7c 00000000 00000000
GPR16: 48830000 10012a8c 00000000 10000af4 00000001 c0810000 00000000 00000000
GPR24: ee9aa920 c0816a18 00000000 00000005 c0019594 edb87bd8 ee20178c edb87b90
NIP [c0093280] smp_call_function_many+0x214/0x2b4
LR [c00930a0] smp_call_function_many+0x34/0x2b4
Call Trace:
[edb87b90] [c00930a0] smp_call_function_many+0x34/0x2b4 (unreliable)
[edb87bd0] [c00194ec] __flush_tlb_page+0xac/0x100
[edb87c00] [c001957c] flush_tlb_page+0x3c/0x54
[edb87c10] [c00180ac] ptep_set_access_flags+0x74/0x12c
[edb87c40] [c0128068] handle_pte_fault+0x2f0/0x9ac
[edb87cb0] [c0128c3c] handle_mm_fault+0x104/0x1dc
[edb87ce0] [c05f40f4] do_page_fault+0x2dc/0x630
[edb87e50] [c001078c] handle_page_fault+0xc/0x80

Signed-off-by: Benjamin Herrenschmidt

powerpc/ppc32/tracing: Add stack frame to calls of trace_hardirqs_on/off

2011-01-21T03:08:33+00:00

32-bit variant of the previous patch for 64-bit:

<<
    When an interrupt occurs in userspace, we can call trace_hardirqs_on/off()
    With one level stack. But if we have irqsoff tracing enabled,
    it checks both CALLER_ADDR0 and CALLER_ADDR1. The second call
    goes two stack frames up. If this is from user space, then there may
    not exist a second stack....
>>

Signed-off-by: Steven Rostedt 
Signed-off-by: Benjamin Herrenschmidt

powerpc: Remove second definition of STACK_FRAME_OVERHEAD

2010-11-29T04:48:23+00:00

Since STACK_FRAME_OVERHEAD is defined in asm/ptrace.h and that
is ASSEMBER safe, we can just include that instead of going via
asm-offsets.h.

Signed-off-by: Stephen Rothwell 
Signed-off-by: Benjamin Herrenschmidt

powerpc/47x: Base ppc476 support

2010-05-05T13:11:10+00:00

This patch adds the base support for the 476 processor.  The code was
primarily written by Ben Herrenschmidt and Torez Smith, but I've been
maintaining it for a while.

The goal is to have a single binary that will run on 44x and 47x, but
we still have some details to work out.  The biggest is that the L1 cache
line size differs on the two platforms, but it's currently a compile-time
option.

Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Torez Smith  
Signed-off-by: Dave Kleikamp 
Signed-off-by: Josh Boyer

powerpc: Use names rather than numbers for SPRGs (v2)

2009-08-20T00:12:27+00:00

The kernel uses SPRG registers for various purposes, typically in
low level assembly code as scratch registers or to hold per-cpu
global infos such as the PACA or the current thread_info pointer.

We want to be able to easily shuffle the usage of those registers
as some implementations have specific constraints realted to some
of them, for example, some have userspace readable aliases, etc..
and the current choice isn't always the best.

This patch should not change any code generation, and replaces the
usage of SPRN_SPRGn everywhere in the kernel with a named replacement
and adds documentation next to the definition of the names as to
what those are used for on each processor family.

The only parts that still use the original numbers are bits of KVM
or suspend/resume code that just blindly needs to save/restore all
the SPRGs.

Signed-off-by: Benjamin Herrenschmidt

powerpc: Add irqtrace support for 32-bit powerpc

2009-06-26T04:37:27+00:00

Based on initial work from: Dale Farnsworth 

Add the low level irq tracing hooks for 32-bit powerpc needed
to enable full lockdep functionality.

The approach taken to deal with the code in entry_32.S is that
we don't trace all the transitions of MSR:EE when we just turn
it off to peek at TI_FLAGS without races. Only when we are
calling into C code or returning from exceptions with a state
that have changed from what lockdep thinks.

There's a little bugger though: If we take an exception that
keeps interrupts enabled (such as an alignment exception) while
interrupts are enabled, we will call trace_hardirqs_on() on the
way back spurriously. Not a big deal, but to get rid of it would
require remembering in pt_regs that the exception was one of the
type that kept interrupts enabled which we don't know at this
stage. (Well, we could test all cases for regs->trap but that
sucks too much).

Signed-off-by: Benjamin Herrenschmidt 
Tested-by: Kumar Gala

powerpc: Unify opcode definitions and support

2009-02-22T23:48:56+00:00

Create a new header that becomes a single location for defining PowerPC
opcodes used by code that is either generationg instructions
at runtime (fixups, debug, etc.), emulating instructions, or just
compiling instructions old assemblers don't know about.

We currently don't handle the floating point emulation or alignment decode
as both are better handled by the specific decode support they already
have.

Added support for the new dcbzl, dcbal, msgsnd, tlbilx, & wait instructions
since older assemblers don't know about them.

Signed-off-by: Kumar Gala 
Signed-off-by: Benjamin Herrenschmidt

powerpc32, ftrace: dynamic function graph tracer

2009-02-22T23:48:55+00:00

This patch gets function graph tracing working with dynamic function
tracer on PowerPC32.

Acked-by: Benjamin Herrenschmidt 
Signed-off-by: Steven Rostedt 
Signed-off-by: Benjamin Herrenschmidt

powerpc32, ftrace: port function graph tracer to ppc32, static only

2009-02-22T23:48:55+00:00

This patch ports the function graph tracer for PowerPC, but only
for static function tracing.

Acked-by: Benjamin Herrenschmidt 
Signed-off-by: Steven Rostedt 
Signed-off-by: Benjamin Herrenschmidt

powerpc32, ftrace: save and restore mcount regs with macro

2009-02-22T23:48:54+00:00

Impact: clean up

Use a macro to save and restore the registers for PowerPC32,
since that code is duplicated.

This is similar to the work done by Cyrill Gorcunov for the
mcount code in x86_64.

Acked-by: Benjamin Herrenschmidt 
Signed-off-by: Steven Rostedt 
Signed-off-by: Benjamin Herrenschmidt