linux-stable.git/arch/powerpc/kernel/Makefile, branch linux-3.4.y

powerpc/perf: Move perf core & PMU code into a subdirectory

2012-02-22T23:50:04+00:00

The perf code has grown a lot since it started, and is big enough to
warrant its own subdirectory. For reference it's ~60% bigger than the
oprofile code. It declutters the kernel directory, makes it simpler to
grep for "just perf stuff", and allows us to shorten some filenames.

While we're at it, make it more obvious that we have two implementations
of the core perf logic. One for (roughly) Book3S CPUs, which was the
original implementation, and the other for Freescale embedded CPUs.

Signed-off-by: Michael Ellerman 
Signed-off-by: Benjamin Herrenschmidt

fadump: Reserve the memory for firmware assisted dump.

2012-02-22T23:50:01+00:00

Reserve the memory during early boot to preserve CPU state data, HPTE region
and RMA (real mode area) region data in case of kernel crash. At the time of
crash, powerpc firmware will store CPU state data, HPTE region data and move
RMA region data to the reserved memory area.

If the firmware-assisted dump fails to reserve the memory, then fallback
to existing kexec-based kdump.

Most of the code implementation to reserve memory has been
adapted from phyp assisted dump implementation written by Linas Vepstas
and Manish Ahuja

This patch also introduces a config option CONFIG_FA_DUMP for firmware
assisted dump feature on Powerpc (ppc64) architecture.

Signed-off-by: Mahesh Salgaonkar 
Signed-off-by: Benjamin Herrenschmidt

powerpc: Process dynamic relocations for kernel

2011-12-20T15:21:08+00:00

The following patch implements the dynamic relocation processing for
PPC32 kernel. relocate() accepts the target virtual address and relocates
 the kernel image to the same.

Currently the following relocation types are handled :

	R_PPC_RELATIVE
	R_PPC_ADDR16_LO
	R_PPC_ADDR16_HI
	R_PPC_ADDR16_HA

The last 3 relocations in the above list depends on value of Symbol indexed
whose index is encoded in the Relocation entry. Hence we need the Symbol
Table for processing such relocations.

Note: The GNU ld for ppc32 produces buggy relocations for relocation types
that depend on symbols. The value of the symbols with STB_LOCAL scope
should be assumed to be zero. - Alan Modra

Signed-off-by: Suzuki K. Poulose 
Signed-off-by: Josh Poimboeuf 
Cc: Paul Mackerras 
Cc: Benjamin Herrenschmidt 
Cc: Alan Modra 
Cc: Kumar Gala 
Cc: linuxppc-dev 
Signed-off-by: Josh Boyer

powerpc: Add jump label support

2011-07-01T03:48:55+00:00

This patch adds support for the new "jump label" feature.

Unlike x86 and sparc we just merrily patch the code with no locks etc,
as far as I know this is safe, but I'm not really sure what the x86/sparc
code is protecting against so maybe it's not.

I also don't see any reason for us to implement the poke_early() routine,
even though sparc does.

[BenH: Updated the patch to upstream generic changes]

Signed-off-by: Michael Ellerman 
Signed-off-by: Benjamin Herrenschmidt

powerpc/ftrace: Implement raw syscall tracepoints on PowerPC

2011-05-26T03:38:57+00:00

This patch implements the raw syscall tracepoints on PowerPC and exports
them for ftrace syscalls to use.

To minimise reworking existing code, I slightly re-ordered the thread
info flags such that the new TIF_SYSCALL_TRACEPOINT bit would still fit
within the 16 bits of the andi. instruction's UI field. The instructions
in question are in /arch/powerpc/kernel/entry_{32,64}.S to and the
_TIF_SYSCALL_T_OR_A with the thread flags to see if system call tracing
is enabled.

In the case of 64bit PowerPC, arch_syscall_addr and
arch_syscall_match_sym_name are overridden to allow ftrace syscalls to
work given the unusual system call table structure and symbol names that
start with a period.

Signed-off-by: Ian Munsie 
Signed-off-by: Benjamin Herrenschmidt

powerpc: Remove unused config in the Makefile

2011-05-19T04:30:40+00:00

The patch below removes an unused config variable found by using a kernel
cleanup script.
Note: I did try to cross compile these but hit erros while doing so..
(gcc is not setup to cross compile) and am unsure if anymore needs to be done.
Please have a look if/when anybody has free time.

Signed-off-by: Justin P. Mattock 
Signed-off-by: Benjamin Herrenschmidt

powerpc/pci: Move IO workarounds to the common kernel dir

2011-04-27T04:18:29+00:00

Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Michael Ellerman 
Signed-off-by: Benjamin Herrenschmidt

powerpc: Add A2 cpu support

2011-04-27T03:02:02+00:00

Add the cputable entry, regs and setup & restore entries for
the PowerPC A2 core.

Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Michael Ellerman 
Signed-off-by: Benjamin Herrenschmidt

powerpc: Add NAP mode support on Power7 in HV mode

2011-04-20T01:03:24+00:00

Wakeup comes from the system reset handler with a potential loss of
the non-hypervisor CPU state. We save the non-volatile state on the
stack and a pointer to it in the PACA, which the system reset handler
uses to restore things

Signed-off-by: Benjamin Herrenschmidt

powerpc: Define CPU feature for Architected 2.06 HV mode

2011-04-20T01:03:22+00:00

This bit indicates that we are operating in hypervisor mode on a CPU
compliant to architecture 2.06 or later (currently server only).

We set it on POWER7 and have a boot-time CPU setup function that
clears it if MSR:HV isn't set (booting under a hypervisor).

Signed-off-by: Benjamin Herrenschmidt