P1023 external IRQ[4:6, 11] are not pin out, but the interrupts are
utilized by the PCIe controllers.  As they are not exposed as pins we
need to set them as active-high (internal to the SoC these interrupts
are pulled down).

IRQs[0:3,7:10] are pulled up on the board so we have them set as
active-low.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
  powerpc/p3060qds: Add support for P3060QDS board
  powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
  powerpc/85xx: Make kexec to interate over online cpus
  powerpc/fsl_booke: Fix comment in head_fsl_booke.S
  powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
  powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
  powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
  powerpc/86xx: Correct Gianfar support for GE boards
  powerpc/cpm: Clear muram before it is in use.
  drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
  powerpc/fsl_msi: add support for "msi-address-64" property
  powerpc/85xx: Setup secondary cores PIR with hard SMP id
  powerpc/fsl-booke: Fix settlbcam for 64-bit
  powerpc/85xx: Adding DCSR node to dtsi device trees
  powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
  powerpc/85xx: fix PHYS_64BIT selection for P1022DS
  powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
  powerpc: respect mem= setting for early memory limit setup
  powerpc: Update corenet64_smp_defconfig
  powerpc: Update mpc85xx/corenet 32-bit defconfigs
  ...

Fix up trivial conflicts in:
 - arch/powerpc/configs/40x/hcu4_defconfig
	removed stale file, edited elsewhere
 - arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
	added opal and gelic drivers vs added ePAPR driver
 - drivers/tty/serial/8250.c
	moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support

The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.

P3060QDS Board Overview:
Memory subsystem:
  - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
  - 128M Bytes NOR flash single-chip memory
  - 16M Bytes SPI flash
  - 8K Bytes AT24C64 I2C EEPROM
Ethernet:
  - 4x1G + 4x1G/2.5G Ethernet controllers
  - 2xRGMII + 1xMII, three VSC8641 PHYs on board
  - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB:  Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C:  Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The GE DTBs were not updated when the Gianfar driver was converted to an
of_platform_driver in commit b31a1d8b41513b96e9c7ec2f68c5734cef0b26a4. Update
the DTBs, adding the required TBI entries.

Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Adding new device tree binding file for the DCSR node.  Modifying device
tree dtsi files to add DCSR node for P2041, P3041, P4080, & P5020.

Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Standarize and document the FPGA nodes used on Freescale QorIQ reference
boards.  There are different kinds of FPGAs used on the boards, but
only two are currently standard: "pixis", "ngpixis", and "qixis".  Although
there are minor differences among the boards that have one kind of FPGA, most
of the functionality is the same, so it makes sense to create common
compatibility strings.

We also need to update the P1022DS platform file, because the compatible
string for its PIXIS node has changed.  This means that older kernels are
not compatible with newer device trees.  This is not a real problem, however,
since that particular function doesn't work anyway.  When the DIU is active,
the PIXIS is in "indirect mode", and so cannot be accessed as a memory-mapped
device.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add:
 - Setup dts node for USB
 - pin description and setup for SMC1 (serial interface)

Update and cleanup mgcoge_defconfig:
- enable: TIPC, UBIFS, USB_GADGET driver, SQUASHFS, HIGHRES timers
          POSIX_MQUEUE, EMBEDDED
- disable: EXT3, PPC_PMAC

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.

During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The P4080 silicon device tree was using PowerPC,4080 while the other
e500mc based SoCs used PowerPC,e500mc.  Use the core name to be
consistent going forward.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>