linux-stable.git/arch/mips, branch v5.4.161 Linux kernel stable tree MIPS: Fix assembly error from MIPSr2 code used within MIPS_ISA_ARCH_LEVEL 2021-11-21T12:38:50+00:00 Maciej W. Rozycki macro@orcam.me.uk 2021-10-21T22:58:23+00:00 307c6f7287284366219750b6d9d89cb6aee85b9c commit a923a2676e60683aee46aa4b93c30aff240ac20d upstream. Fix assembly errors like: {standard input}: Assembler messages: {standard input}:287: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32' {standard input}:680: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32' {standard input}:1274: Error: opcode not supported on this processor: mips3 (mips3) `dins $12,$9,32,32' {standard input}:2175: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32' make[1]: *** [scripts/Makefile.build:277: mm/highmem.o] Error 1 with code produced from `__cmpxchg64' for MIPS64r2 CPU configurations using CONFIG_32BIT and CONFIG_PHYS_ADDR_T_64BIT. This is due to MIPS_ISA_ARCH_LEVEL downgrading the assembly architecture to `r4000' i.e. MIPS III for MIPS64r2 configurations, while there is a block of code containing a DINS MIPS64r2 instruction conditionalized on MIPS_ISA_REV >= 2 within the scope of the downgrade. The assembly architecture override code pattern has been put there for LL/SC instructions, so that code compiles for configurations that select a processor to build for that does not support these instructions while still providing run-time support for processors that do, dynamically switched by non-constant `cpu_has_llsc'. It went in with linux-mips.org commit aac8aa7717a2 ("Enable a suitable ISA for the assembler around ll/sc so that code builds even for processors that don't support the instructions. Plus minor formatting fixes.") back in 2005. Fix the problem by wrapping these instructions along with the adjacent SYNC instructions only, following the practice established with commit cfd54de3b0e4 ("MIPS: Avoid move psuedo-instruction whilst using MIPS_ISA_LEVEL") and commit 378ed6f0e3c5 ("MIPS: Avoid using .set mips0 to restore ISA"). Strictly speaking the SYNC instructions do not have to be wrapped as they are only used as a Loongson3 erratum workaround, so they will be enabled in the assembler by default, but do this so as to keep code consistent with other places. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: c7e2d71dda7a ("MIPS: Fix set_pte() for Netlogic XLR using cmpxchg64()") Cc: stable@vger.kernel.org # v5.1+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a923a2676e60683aee46aa4b93c30aff240ac20d upstream.

Fix assembly errors like:

{standard input}: Assembler messages:
{standard input}:287: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32'
{standard input}:680: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32'
{standard input}:1274: Error: opcode not supported on this processor: mips3 (mips3) `dins $12,$9,32,32'
{standard input}:2175: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32'
make[1]: *** [scripts/Makefile.build:277: mm/highmem.o] Error 1

with code produced from `__cmpxchg64' for MIPS64r2 CPU configurations
using CONFIG_32BIT and CONFIG_PHYS_ADDR_T_64BIT.

This is due to MIPS_ISA_ARCH_LEVEL downgrading the assembly architecture
to `r4000' i.e. MIPS III for MIPS64r2 configurations, while there is a
block of code containing a DINS MIPS64r2 instruction conditionalized on
MIPS_ISA_REV >= 2 within the scope of the downgrade.

The assembly architecture override code pattern has been put there for
LL/SC instructions, so that code compiles for configurations that select
a processor to build for that does not support these instructions while
still providing run-time support for processors that do, dynamically
switched by non-constant `cpu_has_llsc'.  It went in with linux-mips.org
commit aac8aa7717a2 ("Enable a suitable ISA for the assembler around
ll/sc so that code builds even for processors that don't support the
instructions. Plus minor formatting fixes.") back in 2005.

Fix the problem by wrapping these instructions along with the adjacent
SYNC instructions only, following the practice established with commit
cfd54de3b0e4 ("MIPS: Avoid move psuedo-instruction whilst using
MIPS_ISA_LEVEL") and commit 378ed6f0e3c5 ("MIPS: Avoid using .set mips0
to restore ISA").  Strictly speaking the SYNC instructions do not have
to be wrapped as they are only used as a Loongson3 erratum workaround,
so they will be enabled in the assembler by default, but do this so as
to keep code consistent with other places.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: c7e2d71dda7a ("MIPS: Fix set_pte() for Netlogic XLR using cmpxchg64()")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mips: cm: Convert to bitfield API to fix out-of-bounds access 2021-11-17T08:48:44+00:00 Geert Uytterhoeven geert+renesas@glider.be 2021-10-29T09:58:16+00:00 3f698d97f7c5c55adb33d3cc78d96f8930aff770 [ Upstream commit 18b8f5b6fc53d097cadb94a93d8d6566ba88e389 ] mips_cm_error_report() extracts the cause and other cause from the error register using shifts. This works fine for the former, as it is stored in the top bits, and the shift will thus remove all non-related bits. However, the latter is stored in the bottom bits, hence thus needs masking to get rid of non-related bits. Without such masking, using it as an index into the cm2_causes[] array will lead to an out-of-bounds access, probably causing a crash. Fix this by using FIELD_GET() instead. Bite the bullet and convert all MIPS CM handling to the bitfield API, to improve readability and safety. Fixes: 3885c2b463f6a236 ("MIPS: CM: Add support for reporting CM cache errors") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 18b8f5b6fc53d097cadb94a93d8d6566ba88e389 ]

mips_cm_error_report() extracts the cause and other cause from the error
register using shifts.  This works fine for the former, as it is stored
in the top bits, and the shift will thus remove all non-related bits.
However, the latter is stored in the bottom bits, hence thus needs masking
to get rid of non-related bits.  Without such masking, using it as an
index into the cm2_causes[] array will lead to an out-of-bounds access,
probably causing a crash.

Fix this by using FIELD_GET() instead.  Bite the bullet and convert all
MIPS CM handling to the bitfield API, to improve readability and safety.

Fixes: 3885c2b463f6a236 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
MIPS: loongson64: make CPU_LOONGSON64 depends on MIPS_FP_SUPPORT 2021-11-17T08:48:41+00:00 Jackie Liu liuyun01@kylinos.cn 2021-09-13T06:19:08+00:00 56911ee5375fd331a32c9a16075eb63ee02c4873 [ Upstream commit 7f3b3c2bfa9c93ab9b5595543496f570983dc330 ] mach/loongson64 fails to build when the FPU support is disabled: arch/mips/loongson64/cop2-ex.c:45:15: error: implicit declaration of function ‘__is_fpu_owner’; did you mean ‘is_fpu_owner’? [-Werror=implicit-function-declaration] arch/mips/loongson64/cop2-ex.c:98:30: error: ‘struct thread_struct’ has no member named ‘fpu’ arch/mips/loongson64/cop2-ex.c:99:30: error: ‘struct thread_struct’ has no member named ‘fpu’ arch/mips/loongson64/cop2-ex.c:131:43: error: ‘struct thread_struct’ has no member named ‘fpu’ arch/mips/loongson64/cop2-ex.c:137:38: error: ‘struct thread_struct’ has no member named ‘fpu’ arch/mips/loongson64/cop2-ex.c:203:30: error: ‘struct thread_struct’ has no member named ‘fpu’ arch/mips/loongson64/cop2-ex.c:219:30: error: ‘struct thread_struct’ has no member named ‘fpu’ arch/mips/loongson64/cop2-ex.c:283:38: error: ‘struct thread_struct’ has no member named ‘fpu’ arch/mips/loongson64/cop2-ex.c:301:38: error: ‘struct thread_struct’ has no member named ‘fpu’ Fixes: ef2f826c8f2f ("MIPS: Loongson-3: Enable the COP2 usage") Suggested-by: Huacai Chen <chenhuacai@kernel.org> Reviewed-by: Huacai Chen <chenhuacai@kernel.org> Reported-by: k2ci robot <kernel-bot@kylinos.cn> Signed-off-by: Jackie Liu <liuyun01@kylinos.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 7f3b3c2bfa9c93ab9b5595543496f570983dc330 ]

mach/loongson64 fails to build when the FPU support is disabled:

arch/mips/loongson64/cop2-ex.c:45:15: error: implicit declaration of function ‘__is_fpu_owner’; did you mean ‘is_fpu_owner’? [-Werror=implicit-function-declaration]
arch/mips/loongson64/cop2-ex.c:98:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:99:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:131:43: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:137:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:203:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:219:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:283:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:301:38: error: ‘struct thread_struct’ has no member named ‘fpu’

Fixes: ef2f826c8f2f ("MIPS: Loongson-3: Enable the COP2 usage")
Suggested-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reported-by: k2ci robot <kernel-bot@kylinos.cn>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
MIPS: lantiq: dma: reset correct number of channel 2021-11-17T08:48:28+00:00 Aleksander Jan Bajkowski olek2@wp.pl 2021-09-14T21:20:59+00:00 f14eca60bf2308daf32bd62d7776acc76804dda0 [ Upstream commit 5ca9ce2ba4d5884cd94d1a856c675ab1242cd242 ] Different SoCs have a different number of channels, e.g .: * amazon-se has 10 channels, * danube+ar9 have 20 channels, * vr9 has 28 channels, * ar10 has 24 channels. We can read the ID register and, depending on the reported number of channels, reset the appropriate number of channels. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 5ca9ce2ba4d5884cd94d1a856c675ab1242cd242 ]

Different SoCs have a different number of channels, e.g .:
* amazon-se has 10 channels,
* danube+ar9 have 20 channels,
* vr9 has 28 channels,
* ar10 has 24 channels.

We can read the ID register and, depending on the reported
number of channels, reset the appropriate number of channels.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
MIPS: lantiq: dma: add small delay after reset 2021-11-17T08:48:27+00:00 Aleksander Jan Bajkowski olek2@wp.pl 2021-09-14T21:20:58+00:00 ca07aff2575d01bd7183ec513aa8274d1340e993 [ Upstream commit c12aa581f6d5e80c3c3675ab26a52c2b3b62f76e ] Reading the DMA registers immediately after the reset causes Data Bus Error. Adding a small delay fixes this issue. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit c12aa581f6d5e80c3c3675ab26a52c2b3b62f76e ]

Reading the DMA registers immediately after the reset causes
Data Bus Error. Adding a small delay fixes this issue.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
signal/mips: Update (_save|_restore)_fp_context to fail with -EFAULT 2021-11-17T08:48:24+00:00 Eric W. Biederman ebiederm@xmission.com 2021-10-20T17:43:51+00:00 625c3ed247e15bfe9e26294cbcf810f6a84d3812 commit 95bf9d646c3c3f95cb0be7e703b371db8da5be68 upstream. When an instruction to save or restore a register from the stack fails in _save_fp_context or _restore_fp_context return with -EFAULT. This change was made to r2300_fpu.S[1] but it looks like it got lost with the introduction of EX2[2]. This is also what the other implementation of _save_fp_context and _restore_fp_context in r4k_fpu.S does, and what is needed for the callers to be able to handle the error. Furthermore calling do_exit(SIGSEGV) from bad_stack is wrong because it does not terminate the entire process it just terminates a single thread. As the changed code was the only caller of arch/mips/kernel/syscall.c:bad_stack remove the problematic and now unused helper function. Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Maciej Rozycki <macro@orcam.me.uk> Cc: linux-mips@vger.kernel.org [1] 35938a00ba86 ("MIPS: Fix ISA I FP sigcontext access violation handling") [2] f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout") Cc: stable@vger.kernel.org Fixes: f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout") Acked-by: Maciej W. Rozycki <macro@orcam.me.uk> Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Link: https://lkml.kernel.org/r/20211020174406.17889-5-ebiederm@xmission.com Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 95bf9d646c3c3f95cb0be7e703b371db8da5be68 upstream.

When an instruction to save or restore a register from the stack fails
in _save_fp_context or _restore_fp_context return with -EFAULT.  This
change was made to r2300_fpu.S[1] but it looks like it got lost with
the introduction of EX2[2].  This is also what the other implementation
of _save_fp_context and _restore_fp_context in r4k_fpu.S does, and
what is needed for the callers to be able to handle the error.

Furthermore calling do_exit(SIGSEGV) from bad_stack is wrong because
it does not terminate the entire process it just terminates a single
thread.

As the changed code was the only caller of arch/mips/kernel/syscall.c:bad_stack
remove the problematic and now unused helper function.

Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Maciej Rozycki <macro@orcam.me.uk>
Cc: linux-mips@vger.kernel.org
[1] 35938a00ba86 ("MIPS: Fix ISA I FP sigcontext access violation handling")
[2] f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout")
Cc: stable@vger.kernel.org
Fixes: f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout")
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lkml.kernel.org/r/20211020174406.17889-5-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bpf, mips: Validate conditional branch offsets 2021-10-13T08:08:17+00:00 Piotr Krysiuk piotras@gmail.com 2021-09-15T16:04:37+00:00 1a0fe45501a273ac52252448e43f975f0c18811e commit 37cb28ec7d3a36a5bace7063a3dba633ab110f8b upstream. The conditional branch instructions on MIPS use 18-bit signed offsets allowing for a branch range of 128 KBytes (backward and forward). However, this limit is not observed by the cBPF JIT compiler, and so the JIT compiler emits out-of-range branches when translating certain cBPF programs. A specific example of such a cBPF program is included in the "BPF_MAXINSNS: exec all MSH" test from lib/test_bpf.c that executes anomalous machine code containing incorrect branch offsets under JIT. Furthermore, this issue can be abused to craft undesirable machine code, where the control flow is hijacked to execute arbitrary Kernel code. The following steps can be used to reproduce the issue: # echo 1 > /proc/sys/net/core/bpf_jit_enable # modprobe test_bpf test_name="BPF_MAXINSNS: exec all MSH" This should produce multiple warnings from build_bimm() similar to: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 209 at arch/mips/mm/uasm-mips.c:210 build_insn+0x558/0x590 Micro-assembler field overflow Modules linked in: test_bpf(+) CPU: 0 PID: 209 Comm: modprobe Not tainted 5.14.3 #1 Stack : 00000000 807bb824 82b33c9c 801843c0 00000000 00000004 00000000 63c9b5ee 82b33af4 80999898 80910000 80900000 82fd6030 00000001 82b33a98 82087180 00000000 00000000 80873b28 00000000 000000fc 82b3394c 00000000 2e34312e 6d6d6f43 809a180f 809a1836 6f6d203a 80900000 00000001 82b33bac 80900000 00027f80 00000000 00000000 807bb824 00000000 804ed790 001cc317 00000001 [...] Call Trace: [<80108f44>] show_stack+0x38/0x118 [<807a7aac>] dump_stack_lvl+0x5c/0x7c [<807a4b3c>] __warn+0xcc/0x140 [<807a4c3c>] warn_slowpath_fmt+0x8c/0xb8 [<8011e198>] build_insn+0x558/0x590 [<8011e358>] uasm_i_bne+0x20/0x2c [<80127b48>] build_body+0xa58/0x2a94 [<80129c98>] bpf_jit_compile+0x114/0x1e4 [<80613fc4>] bpf_prepare_filter+0x2ec/0x4e4 [<8061423c>] bpf_prog_create+0x80/0xc4 [<c0a006e4>] test_bpf_init+0x300/0xba8 [test_bpf] [<8010051c>] do_one_initcall+0x50/0x1d4 [<801c5e54>] do_init_module+0x60/0x220 [<801c8b20>] sys_finit_module+0xc4/0xfc [<801144d0>] syscall_common+0x34/0x58 [...] ---[ end trace a287d9742503c645 ]--- Then the anomalous machine code executes: => 0xc0a18000: addiu sp,sp,-16 0xc0a18004: sw s3,0(sp) 0xc0a18008: sw s4,4(sp) 0xc0a1800c: sw s5,8(sp) 0xc0a18010: sw ra,12(sp) 0xc0a18014: move s5,a0 0xc0a18018: move s4,zero 0xc0a1801c: move s3,zero # __BPF_STMT(BPF_LDX | BPF_B | BPF_MSH, 0) 0xc0a18020: lui t6,0x8012 0xc0a18024: ori t4,t6,0x9e14 0xc0a18028: li a1,0 0xc0a1802c: jalr t4 0xc0a18030: move a0,s5 0xc0a18034: bnez v0,0xc0a1ffb8 # incorrect branch offset 0xc0a18038: move v0,zero 0xc0a1803c: andi s4,s3,0xf 0xc0a18040: b 0xc0a18048 0xc0a18044: sll s4,s4,0x2 [...] # __BPF_STMT(BPF_LDX | BPF_B | BPF_MSH, 0) 0xc0a1ffa0: lui t6,0x8012 0xc0a1ffa4: ori t4,t6,0x9e14 0xc0a1ffa8: li a1,0 0xc0a1ffac: jalr t4 0xc0a1ffb0: move a0,s5 0xc0a1ffb4: bnez v0,0xc0a1ffb8 # incorrect branch offset 0xc0a1ffb8: move v0,zero 0xc0a1ffbc: andi s4,s3,0xf 0xc0a1ffc0: b 0xc0a1ffc8 0xc0a1ffc4: sll s4,s4,0x2 # __BPF_STMT(BPF_LDX | BPF_B | BPF_MSH, 0) 0xc0a1ffc8: lui t6,0x8012 0xc0a1ffcc: ori t4,t6,0x9e14 0xc0a1ffd0: li a1,0 0xc0a1ffd4: jalr t4 0xc0a1ffd8: move a0,s5 0xc0a1ffdc: bnez v0,0xc0a3ffb8 # correct branch offset 0xc0a1ffe0: move v0,zero 0xc0a1ffe4: andi s4,s3,0xf 0xc0a1ffe8: b 0xc0a1fff0 0xc0a1ffec: sll s4,s4,0x2 [...] # epilogue 0xc0a3ffb8: lw s3,0(sp) 0xc0a3ffbc: lw s4,4(sp) 0xc0a3ffc0: lw s5,8(sp) 0xc0a3ffc4: lw ra,12(sp) 0xc0a3ffc8: addiu sp,sp,16 0xc0a3ffcc: jr ra 0xc0a3ffd0: nop To mitigate this issue, we assert the branch ranges for each emit call that could generate an out-of-range branch. Fixes: 36366e367ee9 ("MIPS: BPF: Restore MIPS32 cBPF JIT") Fixes: c6610de353da ("MIPS: net: Add BPF JIT") Signed-off-by: Piotr Krysiuk <piotras@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Johan Almbladh <johan.almbladh@anyfinetworks.com> Acked-by: Johan Almbladh <johan.almbladh@anyfinetworks.com> Cc: Paul Burton <paulburton@kernel.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Link: https://lore.kernel.org/bpf/20210915160437.4080-1-piotras@gmail.com Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 37cb28ec7d3a36a5bace7063a3dba633ab110f8b upstream.

The conditional branch instructions on MIPS use 18-bit signed offsets
allowing for a branch range of 128 KBytes (backward and forward).
However, this limit is not observed by the cBPF JIT compiler, and so
the JIT compiler emits out-of-range branches when translating certain
cBPF programs. A specific example of such a cBPF program is included in
the "BPF_MAXINSNS: exec all MSH" test from lib/test_bpf.c that executes
anomalous machine code containing incorrect branch offsets under JIT.

Furthermore, this issue can be abused to craft undesirable machine
code, where the control flow is hijacked to execute arbitrary Kernel
code.

The following steps can be used to reproduce the issue:

  # echo 1 > /proc/sys/net/core/bpf_jit_enable
  # modprobe test_bpf test_name="BPF_MAXINSNS: exec all MSH"

This should produce multiple warnings from build_bimm() similar to:

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 209 at arch/mips/mm/uasm-mips.c:210 build_insn+0x558/0x590
  Micro-assembler field overflow
  Modules linked in: test_bpf(+)
  CPU: 0 PID: 209 Comm: modprobe Not tainted 5.14.3 #1
  Stack : 00000000 807bb824 82b33c9c 801843c0 00000000 00000004 00000000 63c9b5ee
          82b33af4 80999898 80910000 80900000 82fd6030 00000001 82b33a98 82087180
          00000000 00000000 80873b28 00000000 000000fc 82b3394c 00000000 2e34312e
          6d6d6f43 809a180f 809a1836 6f6d203a 80900000 00000001 82b33bac 80900000
          00027f80 00000000 00000000 807bb824 00000000 804ed790 001cc317 00000001
  [...]
  Call Trace:
  [<80108f44>] show_stack+0x38/0x118
  [<807a7aac>] dump_stack_lvl+0x5c/0x7c
  [<807a4b3c>] __warn+0xcc/0x140
  [<807a4c3c>] warn_slowpath_fmt+0x8c/0xb8
  [<8011e198>] build_insn+0x558/0x590
  [<8011e358>] uasm_i_bne+0x20/0x2c
  [<80127b48>] build_body+0xa58/0x2a94
  [<80129c98>] bpf_jit_compile+0x114/0x1e4
  [<80613fc4>] bpf_prepare_filter+0x2ec/0x4e4
  [<8061423c>] bpf_prog_create+0x80/0xc4
  [<c0a006e4>] test_bpf_init+0x300/0xba8 [test_bpf]
  [<8010051c>] do_one_initcall+0x50/0x1d4
  [<801c5e54>] do_init_module+0x60/0x220
  [<801c8b20>] sys_finit_module+0xc4/0xfc
  [<801144d0>] syscall_common+0x34/0x58
  [...]
  ---[ end trace a287d9742503c645 ]---

Then the anomalous machine code executes:

=> 0xc0a18000:  addiu   sp,sp,-16
   0xc0a18004:  sw      s3,0(sp)
   0xc0a18008:  sw      s4,4(sp)
   0xc0a1800c:  sw      s5,8(sp)
   0xc0a18010:  sw      ra,12(sp)
   0xc0a18014:  move    s5,a0
   0xc0a18018:  move    s4,zero
   0xc0a1801c:  move    s3,zero

   # __BPF_STMT(BPF_LDX | BPF_B | BPF_MSH, 0)
   0xc0a18020:  lui     t6,0x8012
   0xc0a18024:  ori     t4,t6,0x9e14
   0xc0a18028:  li      a1,0
   0xc0a1802c:  jalr    t4
   0xc0a18030:  move    a0,s5
   0xc0a18034:  bnez    v0,0xc0a1ffb8           # incorrect branch offset
   0xc0a18038:  move    v0,zero
   0xc0a1803c:  andi    s4,s3,0xf
   0xc0a18040:  b       0xc0a18048
   0xc0a18044:  sll     s4,s4,0x2
   [...]

   # __BPF_STMT(BPF_LDX | BPF_B | BPF_MSH, 0)
   0xc0a1ffa0:  lui     t6,0x8012
   0xc0a1ffa4:  ori     t4,t6,0x9e14
   0xc0a1ffa8:  li      a1,0
   0xc0a1ffac:  jalr    t4
   0xc0a1ffb0:  move    a0,s5
   0xc0a1ffb4:  bnez    v0,0xc0a1ffb8           # incorrect branch offset
   0xc0a1ffb8:  move    v0,zero
   0xc0a1ffbc:  andi    s4,s3,0xf
   0xc0a1ffc0:  b       0xc0a1ffc8
   0xc0a1ffc4:  sll     s4,s4,0x2

   # __BPF_STMT(BPF_LDX | BPF_B | BPF_MSH, 0)
   0xc0a1ffc8:  lui     t6,0x8012
   0xc0a1ffcc:  ori     t4,t6,0x9e14
   0xc0a1ffd0:  li      a1,0
   0xc0a1ffd4:  jalr    t4
   0xc0a1ffd8:  move    a0,s5
   0xc0a1ffdc:  bnez    v0,0xc0a3ffb8           # correct branch offset
   0xc0a1ffe0:  move    v0,zero
   0xc0a1ffe4:  andi    s4,s3,0xf
   0xc0a1ffe8:  b       0xc0a1fff0
   0xc0a1ffec:  sll     s4,s4,0x2
   [...]

   # epilogue
   0xc0a3ffb8:  lw      s3,0(sp)
   0xc0a3ffbc:  lw      s4,4(sp)
   0xc0a3ffc0:  lw      s5,8(sp)
   0xc0a3ffc4:  lw      ra,12(sp)
   0xc0a3ffc8:  addiu   sp,sp,16
   0xc0a3ffcc:  jr      ra
   0xc0a3ffd0:  nop

To mitigate this issue, we assert the branch ranges for each emit call
that could generate an out-of-range branch.

Fixes: 36366e367ee9 ("MIPS: BPF: Restore MIPS32 cBPF JIT")
Fixes: c6610de353da ("MIPS: net: Add BPF JIT")
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Acked-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/bpf/20210915160437.4080-1-piotras@gmail.com
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MIPS: BPF: Restore MIPS32 cBPF JIT 2021-10-13T08:08:17+00:00 Paul Burton paulburton@kernel.org 2019-12-05T18:23:18+00:00 7ed040244595db01e765d58d3fdc2d3817f55934 commit 36366e367ee93ced84fddb8fae6675e12985f5a4 upstream. Commit 716850ab104d ("MIPS: eBPF: Initial eBPF support for MIPS32 architecture.") enabled our eBPF JIT for MIPS32 kernels, whereas it has previously only been availailable for MIPS64. It was my understanding at the time that the BPF test suite was passing & JITing a comparable number of tests to our cBPF JIT [1], but it turns out that was not the case. The eBPF JIT has a number of problems on MIPS32: - Most notably various code paths still result in emission of MIPS64 instructions which will cause reserved instruction exceptions & kernel panics when run on MIPS32 CPUs. - The eBPF JIT doesn't account for differences between the O32 ABI used by MIPS32 kernels versus the N64 ABI used by MIPS64 kernels. Notably arguments beyond the first 4 are passed on the stack in O32, and this is entirely unhandled when JITing a BPF_CALL instruction. Stack space must be reserved for arguments even if they all fit in registers, and the callee is free to assume that stack space has been reserved for its use - with the eBPF JIT this is not the case, so calling any function can result in clobbering values on the stack & unpredictable behaviour. Function arguments in eBPF are always 64-bit values which is also entirely unhandled - the JIT still uses a single (32-bit) register per argument. As a result all function arguments are always passed incorrectly when JITing a BPF_CALL instruction, leading to kernel crashes or strange behavior. - The JIT attempts to bail our on use of ALU64 instructions or 64-bit memory access instructions. The code doing this at the start of build_one_insn() incorrectly checks whether BPF_OP() equals BPF_DW, when it should really be checking BPF_SIZE() & only doing so when BPF_CLASS() is one of BPF_{LD,LDX,ST,STX}. This results in false positives that cause more bailouts than intended, and that in turns hides some of the problems described above. - The kernel's cBPF->eBPF translation makes heavy use of 64-bit eBPF instructions that the MIPS32 eBPF JIT bails out on, leading to most cBPF programs not being JITed at all. Until these problems are resolved, revert the removal of the cBPF JIT performed by commit 716850ab104d ("MIPS: eBPF: Initial eBPF support for MIPS32 architecture."). Together with commit f8fffebdea75 ("MIPS: BPF: Disable MIPS32 eBPF JIT") this restores MIPS32 BPF JIT behavior back to the same state it was prior to the introduction of the broken eBPF JIT support. [1] https://lore.kernel.org/linux-mips/MWHPR2201MB13583388481F01A422CE7D66D4410@MWHPR2201MB1358.namprd22.prod.outlook.com/ Signed-off-by: Paul Burton <paulburton@kernel.org> Fixes: 716850ab104d ("MIPS: eBPF: Initial eBPF support for MIPS32 architecture.") Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Hassan Naveed <hnaveed@wavecomp.com> Cc: Tony Ambardar <itugrok@yahoo.com> Cc: bpf@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 36366e367ee93ced84fddb8fae6675e12985f5a4 upstream.

Commit 716850ab104d ("MIPS: eBPF: Initial eBPF support for MIPS32
architecture.") enabled our eBPF JIT for MIPS32 kernels, whereas it has
previously only been availailable for MIPS64. It was my understanding at
the time that the BPF test suite was passing & JITing a comparable
number of tests to our cBPF JIT [1], but it turns out that was not the
case.

The eBPF JIT has a number of problems on MIPS32:

- Most notably various code paths still result in emission of MIPS64
  instructions which will cause reserved instruction exceptions & kernel
  panics when run on MIPS32 CPUs.

- The eBPF JIT doesn't account for differences between the O32 ABI used
  by MIPS32 kernels versus the N64 ABI used by MIPS64 kernels. Notably
  arguments beyond the first 4 are passed on the stack in O32, and this
  is entirely unhandled when JITing a BPF_CALL instruction. Stack space
  must be reserved for arguments even if they all fit in registers, and
  the callee is free to assume that stack space has been reserved for
  its use - with the eBPF JIT this is not the case, so calling any
  function can result in clobbering values on the stack & unpredictable
  behaviour. Function arguments in eBPF are always 64-bit values which
  is also entirely unhandled - the JIT still uses a single (32-bit)
  register per argument. As a result all function arguments are always
  passed incorrectly when JITing a BPF_CALL instruction, leading to
  kernel crashes or strange behavior.

- The JIT attempts to bail our on use of ALU64 instructions or 64-bit
  memory access instructions. The code doing this at the start of
  build_one_insn() incorrectly checks whether BPF_OP() equals BPF_DW,
  when it should really be checking BPF_SIZE() & only doing so when
  BPF_CLASS() is one of BPF_{LD,LDX,ST,STX}. This results in false
  positives that cause more bailouts than intended, and that in turns
  hides some of the problems described above.

- The kernel's cBPF->eBPF translation makes heavy use of 64-bit eBPF
  instructions that the MIPS32 eBPF JIT bails out on, leading to most
  cBPF programs not being JITed at all.

Until these problems are resolved, revert the removal of the cBPF JIT
performed by commit 716850ab104d ("MIPS: eBPF: Initial eBPF support for
MIPS32 architecture."). Together with commit f8fffebdea75 ("MIPS: BPF:
Disable MIPS32 eBPF JIT") this restores MIPS32 BPF JIT behavior back to
the same state it was prior to the introduction of the broken eBPF JIT
support.

[1] https://lore.kernel.org/linux-mips/MWHPR2201MB13583388481F01A422CE7D66D4410@MWHPR2201MB1358.namprd22.prod.outlook.com/

Signed-off-by: Paul Burton <paulburton@kernel.org>
Fixes: 716850ab104d ("MIPS: eBPF: Initial eBPF support for MIPS32 architecture.")
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Hassan Naveed <hnaveed@wavecomp.com>
Cc: Tony Ambardar <itugrok@yahoo.com>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers: base: cacheinfo: Get rid of DEFINE_SMP_CALL_CACHE_FUNCTION() 2021-09-26T12:07:10+00:00 Thomas Gleixner tglx@linutronix.de 2021-08-31T11:48:34+00:00 2f7bfc07e38662077f802abe56715b5e92663364 [ Upstream commit 4b92d4add5f6dcf21275185c997d6ecb800054cd ] DEFINE_SMP_CALL_CACHE_FUNCTION() was usefel before the CPU hotplug rework to ensure that the cache related functions are called on the upcoming CPU because the notifier itself could run on any online CPU. The hotplug state machine guarantees that the callbacks are invoked on the upcoming CPU. So there is no need to have this SMP function call obfuscation. That indirection was missed when the hotplug notifiers were converted. This also solves the problem of ARM64 init_cache_level() invoking ACPI functions which take a semaphore in that context. That's invalid as SMP function calls run with interrupts disabled. Running it just from the callback in context of the CPU hotplug thread solves this. Fixes: 8571890e1513 ("arm64: Add support for ACPI based firmware tables") Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Will Deacon <will@kernel.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/871r69ersb.ffs@tglx Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 4b92d4add5f6dcf21275185c997d6ecb800054cd ]

DEFINE_SMP_CALL_CACHE_FUNCTION() was usefel before the CPU hotplug rework
to ensure that the cache related functions are called on the upcoming CPU
because the notifier itself could run on any online CPU.

The hotplug state machine guarantees that the callbacks are invoked on the
upcoming CPU. So there is no need to have this SMP function call
obfuscation. That indirection was missed when the hotplug notifiers were
converted.

This also solves the problem of ARM64 init_cache_level() invoking ACPI
functions which take a semaphore in that context. That's invalid as SMP
function calls run with interrupts disabled. Running it just from the
callback in context of the CPU hotplug thread solves this.

Fixes: 8571890e1513 ("arm64: Add support for ACPI based firmware tables")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/871r69ersb.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
MIPS: Malta: fix alignment of the devicetree buffer 2021-09-22T10:26:26+00:00 Oleksij Rempel o.rempel@pengutronix.de 2021-09-02T07:19:51+00:00 0ac2ecb915e8012145f8ed8a9d769ee5ff8e21be [ Upstream commit bea6a94a279bcbe6b2cde348782b28baf12255a5 ] Starting with following patch MIPS Malta is not able to boot: | commit 79edff12060fe7772af08607eff50c0e2486c5ba | Author: Rob Herring <robh@kernel.org> | scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9 The reason is the alignment test added to the fdt_ro_probe_(). To fix this issue, we need to make sure that fdt_buf is aligned. Since the dtc patch was designed to uncover potential issue, I handle initial MIPS Malta patch as initial bug. Fixes: e81a8c7dabac ("MIPS: Malta: Setup RAM regions via DT") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit bea6a94a279bcbe6b2cde348782b28baf12255a5 ]

Starting with following patch MIPS Malta is not able to boot:
| commit 79edff12060fe7772af08607eff50c0e2486c5ba
| Author: Rob Herring <robh@kernel.org>
| scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9

The reason is the alignment test added to the fdt_ro_probe_(). To fix
this issue, we need to make sure that fdt_buf is aligned.

Since the dtc patch was designed to uncover potential issue, I handle
initial MIPS Malta patch as initial bug.

Fixes: e81a8c7dabac ("MIPS: Malta: Setup RAM regions via DT")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>